Univex IK - TF1 User Manual

Specifications and Main Features

  • Model Model Number is: IK – TF 1.
  • The camera works best with a DC supply of 12V or more while making sure it does not exceed 10%.
  • The total watts consumed are calculated to be 3.6W.
  • There are three separate pickup systems for RGB(micro prism system 3 CDD for each of the colors).
  • The camera/sensor takes the use of 1/3 IT CCD(Charge Coupled Device) which is known to perform under various angles and colors.
  • When scanning, the camera creates an image of 768 pixels sharp horizontally and 494 pixels vertically.
  • The scanning system utilizes a method of 2:1 interlace, it works exceptionally well together.
  • The camera functions at a hworking horizontal frequency of 15.734 kHz and a vertical of 59.94 Hz.
  • The camera is able to switch between an internal sync system and external one automatically depending on the conditions set – Switchable.
  • The resolution of the image captured goes up to 570 TV lines.
  • The camera has been tested to offer amazing sensitivity and works optimally above F8 standard at 2000 lx, 3000 K temperature.
  • The sensor is able to work optimally in room conditions and requires a low illumination of 10 lx or above accompanied by a F2.2 sensitivity rating at 3000K.
  • The signal to noise ratio achieved by the camera can reach up to an impressive 64 dB.
  • The camera lens lies on a C mounted sensor with a flange back allowance of approximately 17.526 mm in an airy environment.
  • With the Cameras most preferable temperature being anywhere between 32-104°F or 12-40C.
  • The cameras ambient Humidity with the best functionalities is 90% or less.
  • With a rough weight of 155 g(5.4702 oz) attached, the sensor is lightweight and can be easily used.
  • In regards to the sensor size, it measures around 1.73 inches approximately alongside height and depth.
  • The sensor is capable of switching its white balance on an automatic to manual setting and vice versa.
  • With the option to choose from manual setting to auto, the camera offers a variety of settings.
  • The camera shows an output signal of RGB; 752 unbalanced alongside a D-sub 15 pin connector .
  • Additionally, the camera has the option to use HD or VD and work through 2-5 volts while using a faxing negative system.
  • SYNC Working smartly has enables super vision capabilities while having a 2.0V+/- 1V working ratio.
  • HD, VD, INDEX: Vo Vi (p-p), Type Negative, Load Impedance: Greater than 10 kΩ
  • External Trigger Input: Low Level: Below 0.4V, High Level: 3.4 – 5V
  • IN: RS-232C Serial Data Interface; OUT: RS-232C Serial Data Interface
  • Optional Parts: EXC-TFO5B (RGB cable), etc.
  • There may be changes without notice in design and specifications.

Frequently Asked Questions

Q: What power supply is needed for the IK-TF1 camera?

A: You will need a DC12V supply which is about ± 10% for the IK-TF1 camera.

Q: What about the weight of the device?

A: The IK-TF1 weight is around 155 g which is equivalent to 5.4702 oz.

Q: Is it possible to use this camera in a house or neighborhood affecting any causes?

A: This particular camera may not be used in residential places due to it being a class A device which means it can affect surrounding devices negatively which the IK-TF1 does.

Q: What required is the lowest light that is applicable for the camera to function properly?

A: The minimum F2.2 for this camera is 10 lx having a sensitivity of +18 dB with a temperature of 3000K.

Q: Is the camera equipped with IK-TF1 automatic white balance feature?

A: The camera does have an AWB support but also manual adjustments can be applied for white balance which is useful for the manual shifting of the camera.

Q: What is the resolution of the camera?

A: The horizontal resolution of the camera is 570 TV lines as detailed in the specifications of the IK-TF1 model.

Q: What is the type of lens that can be used with this camera?

A: Ik-Tf1 model is able to use C mount lenses.

Q: What are temperatures in which the camera will work safely?

A: As per the specifications of IK-TF1 camera, the operating temperature starts from 32 degrees and can go up to 104 degrees Fahrenheit which means between 0 to around 40 degrees Celsius.

Q: How is the external sync input defined for the device?

A: Internal specifications allow the use of external sync input for IK-TF1 that receives HD or VD signal between 2 to 5 volts which are negative.

Q: Is the weight of the device important? What does this weight represent?

A: The approximate weight of the device is 155 grams and this means that the device is portable and suitable for other applications too.

User Manual

Page 1
Univex IK - TF1 User Manual
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Loading...