Univex duro 7510, duro 7512 Instruction Manual

INSTRUCTION 7510,7512

7510/12/1099

ED7

MANUAL

DURO SERIES Slicer

WE THANK YOU FOR YOUR PURCHASE OF OUR
MODEL 7510, 7512 SLICER.

SINCE 1948

7510/7512

TABLE OF CONTENTS

DESCRIPTION PAGE

Table of Contents 1
List of Illustrations 1
Introduction 3
Installation Instructions 3
Important Safety Warnings 3
Operating Instructions 4
Sharpening Instructions 4-5
Operator's Care of Slicer / Lubrication 5-6
Trouble Shooting Chart 8
Mechanics Maintenance 9
Repair, incl. Disassembly, Replacement and Reassembly 10-12
Replacement of Parts, List 13-26
Warranty Back Cover

LIST OF ILLUSTRATIONS

ILLUSTRATION PAGE

Figure 1 Overall View of Meat Slicer, Model 7510-7512 2
Figure 2 Lubrication Diagram, Model 7510-7512 7
Figure 3 Base and Knife Housing Assembly 13-14
Figure 4 Sharpening Assembly 15
Figure 5 Carnage Assembly, Model 7510 16
Figure 5A Carnage assembly, Model 7512 17
Figure 6 Carnage Ann and Slide Assembly 18
Figure 7 Slice Adjustment Assembly 19
Figure 8 Fence Assembly 20
Figure 9 Motor, Mount and Drive Assembly 115V, 50/60 21-22
Figure 9A Capacitor Panel 100V, 50/60HZ, 1PH 23
Figure 10 Motor, Mount and Drive Assembly 220V, 50HZ 24-25
Figure 10A Capacitor Panel 220-240 V, 50/60HZ, 1PH 26
Figure 11 Electrical Wiring Diagram (115V , 60/50HZ , 1PH) 27
Figure 11 A Electrical Wiring Diagram (220-240V, 50/60HZ, 1PH) 28
Figure 11B Electrical Wiring Diagram (100V, 50/60HZ, 1PH) 29

PAGE 1

OVERALL VIEW OF MEAT SLICER

MODEL 7510 - 7512

FIGURE 1

7510/7512

1 ON-OFF SWITCH 8 ADJUSTMENT SPACER
2 INDICATOR LIGHT 9 ELECTRIC CORD
3 CARRIAGE 10 CARRIAGE ARM KNOB
4 FENCE 11 CARRIAGE ARM
5 LAST SLICE DEVICE 12 REMOVABLE CHEESE SCRAPER
6 KNIFE SHARPENER 13 GRADUATED KNOB
7 KNIFE GUARD 14 SERIAL NAME PLATE (ON REAR)

PAGE 2

7510/7512

This manual contains instructions for the Installation, Operation, Care, Maintenance and Repair of the

guide is provided. A complete Replacement Parts list with identifying figures is also

carefully by the person making the installation for loose, damaged or broken parts. Detached parts and

fixtures should be checked against packing list to determine all are present. Any damages should be

After slicer has been inspected, wash slicer completely with warm water and mild soap.

The most efficient installation of your Univex slicer will depend upon the layout of your kitchen.

Locate your slicer where it will save steps for the operator and be sure to provide sufficient clearance

Slicer should be operated on a sturdy bench or table with the height determined to suit the operator. It

is most important that the forearm of the operator be at the proper level for ease and safety of

as well as for maximum production. This height is considered optimum when the carriage

of the slicer is at approximately the height of the operator's elbow when

standing.

Fig.

1B). Before making electrical connections, CHECK the

specifications on the name plate to make sure that they agree with those on

rovided for

safety. If you do not have a mating receptacle, have a qualified electrician

hands and fingers clear of the

knife. Never run slicer without the guard or other parts in place and securely fastened. Take extra care

to avoid accidents by keeping the knife guard and sharpening assembly cover ON at all times. When

use, the slice adjustment knob should be turned back to the closed position

for best results and for safety. Also remember to always

Do not

INSTRUCTION MANUAL

INTRODUCTION

Meat Slicing Machine. Disassembly, Replacement and Reassembly Instructions are included. A
trouble shooting
included to facilitate identification and ordering of replacement parts.

INSTALLATION INSTRUCTIONS:

INSPECTION

All Univex slicers are inspected and tested at the factory; however, they should be reinspected

reported to t he Carrier immediately, and any shortages of parts or fixtures reported to Univex
Corporation.

WARNING:

For SAFETY follow the cleaning instructions on page 5-6.

INSTALLATION:

around it for ease of maintenance and cleaning, as well as for efficient and safe use.

operation
handle (Figure 1 [11])

IMPORTANT

WARNING\CAUTION: Electrical wiring instructions are found in the wiring diagram fFig. 11.

11 A and Fig. 1

your electrical service. A grounding type three terminal plug is p
provide grounding provisions in accordance with local safety codes.

IMPORTANT SAFETY WARNINGS

The slicer knife is extremely sharp! Never touch the knife, always keep

the machine is not in
(beyond "0") so that the knife edge is not exposed.

Observe the cleaning instructions on Page 5-6
turn off slicer and disconnect the electrical supply cord.

When slicing, always work the carriage using only the carriage arm handle (Figure 1 [11]).
hold or push the carriage from any other place.

PAGE 3

7510/7512

The Univex slicer is designed to meet the Cook's demand for an efficient, sturdy slicer. The Univex

upward to the ON position.

allows for slice thicknesses ranging from

Dial graduations allow you to precisely set up specific slice

thickness for various needs. When not in use, always return knob back to its fully

is provided which can be locked out of the

iage back and

Always make sure the carriage is positively secured to the slicer by checking to see that the carriage

he carriage striking and

covers the knife edge completely except under the

sharpener cover and the forward edge where slicing will be performed. This forward

can be removed for cleaning by unscrewing the knife

For safety, keep the knife guard on at all times except when

This slicer is equipped with a knife having a concave or hollowed rear surface for superior slicing

gularly and properly in order to

produce not only the highest quality slices, but also to allow it to maintain its productivity. The knife

in design for simplicity and ease of

The following sharpening procedure will provide high quality sharpening results and

The knife's cutting area should be clean and free from food, especially grease. Grease will ruin the

OPERATION INSTRUCTIONS

slicer will give unfailing performance over a period of years, when operated and maintained
according to instructions contained herein.

START/STOP SWITCH

The slicer is started by pushing the start/stop toggle switch (Figure 1 [ 1 ])
A pilot light (Figure 1 [2]) is provided to indicate when the slicer is turned on.

SLICE ADJUSTMENT
WARNING:

Dial type knob adjustment (Figure 1 [13])
paper thin up to 5/8".

closed position (beyond "0") so that the knife edge is not exposed.

POSITIVE HOLD CARRIAGE
CAUTION:

A last slice gravity feed grip (Figure 1 [5])
way when not required. Do not use this last slice device to work the carr
forth. Use only the carriage arm handle (Figure 1 [11]).

arm knob (Figure 1 [10]) is fully tightened. Failure to do this could result in t
damaging the knife edge.

KNIFE GUARD
WARNING:

The knife guard (Figure 1 [7])

edge is covered by the edge of the fence, but only when the slice adjustment is
completely closed.

The knife guard (Figure 1 [7])
guard knob (Figure 3 [2]).
cleaning. Never operate the slicer with the knife guard removed.

SHARPENING INSTRUCTIONS

quality. Of course, any knife however superior must be sharpened re
sharpener (Figure 1 [6]) on this machine is a top mounted built -

use. It even has an automatic aligning feature.

WARNING:

should also be followed for safety considerations:

(1) WARNING: Keep away from the knife edge.
(2) Completely close the slice adjustment (beyond "0") so that the knife edge is not exposed.
(3)

ability of a grinding stone to sharpen an edge. The stone simply will not cut. If cleanin g is

PAGE 4

7510/7512

necessary, follow the procedure outlined on Page 5-6. Remem ber to unplug the electrical supply cord.

(4) Loosen sharpener lock pin (Figure 3 [4]) which bears against sharpener post, then lift sharpener assembly

(Figure 1 [6]) and rotate it 1/2 turn (180 degrees). Then seat it down over knife.

(5) Tighten sharpener lock pin (Figure 3 [4]). As the lock is tightened, it bears on the sharpener post and

automatically aligns the grinding and debumng stones to the precise orientations which are preset at our
factory.

(6) Turn slicer ON. Depress the sharpener button and hold in which will start the grinding wheel rotating. Run

until the beveled cutting surface cleans up. This can take from 30 seconds to several minutes depending on
how dull the blade was allowed to become. Release sharpener button.

(7) Turn slicer OFF and check for the formation of a very slight burr on the side of knife opposite the bevel

which indicates complete grinding of the bevel. This slight burr can be detected either visually of by picking
with a small piece of stiff paper.

(8) Turn slicer ON. Lightly press deburring (honing) button and hold for 1 to 2 seconds while you turn OFF the

slicer. Blade should now be completely sharpened and honed.

CAUTION: It is very important for best slicing results not to deburr the knife too lone or the keen edge will
be destroyed due to the formation of an undesirable second bevel on the opposite side. This condition tends to
be the primary cause of unsatisfactory slicing results.

(9) Turn slicer OFF. Loosen lock pin, ( Figure 3 [4]) then lift and return sharpener to its storage position. Tighten

lock pin.

(10) Clean slicer and knife according to the cleaning procedure on Page 5-6 in order to thoroughly remove

grinding debris.

OPERATOR'S CARE OF SLICER

CLEANING

WARNING: 1. Never touch the knife. Always keep your hands, fingers and arms clear of knife.

WARNING: 4. Remove carriage assembly (Figure 1 [11]) which may be washed in a sink. Use care in

2. Turn off slicer and DISCONNECT ELECTRICAL CORD (Figure 1 [9]) before cleaning.
Leave protective guard in place.

3. Turn slice adjustment knob (Figure 1 [13]) to the fully closed position (beyond "0") so that the
knife edge is not exposed.

washing the sharply pointed prongs on the last slice feed grip. (Figure 1 [5]) Wash this area
thoroughly. A small bristle brush is recommended. Use only warm water and mild soap. Rinse
carriage assembly with warm water and dry thoroughly using a clean soft cloth.

Never use detergents nor wash the slicer or any of its parts in a dishwashing machine or the
clear protective finish will be damaged.

PAGE 5

7510/7512

th. Under

no circumstances should the slicer be hose rinsed. It is recommended that the

cloth be folded over a thin wooden stick when cleaning between the fence plate

and pushing the long stud upward to lift the knife guard above surface of knife.

front and rear of the knife with a cloth using warm

water and mild soap. It is recommended that the cloth be folded over a thin

wooden stick as a further caution to avoid accidental contact with the knife.

oroughly with a clean soft

cloth.

ible with anodized

aluminum or the clear protective finish on the slicer will be damaged. Surfaces

Operator's attention is called to lubricating

three

should be

lubricated as necessary with petrogel. Distribute over surfaces by moving the grip and fence back and

WARNING:

5. Wash body of slicer using warm water and mild soap using a soft clo

and the knife.

WARNING:

6. Remove knife guard (Figure 1 [7]) by loosening knife guard knob (Figure 3 [2])

Then carefully lift and remove guard.

7. Remove Knife deflector (Fig. 3 [19]) by unscrewing Knife deflector screw (Fig.
3 [21]).

8. CAREFULLY wash the

Rinse with warm water applied with a cloth. Dry th

WARNING:

9. Following cleaning, a commercial non-toxic sanitizer may be wiped on the
clean surfaces with a soft clean cloth or sprayed as recommended on the
container labeling. It is important that the sanitizer be compat

should be wetted completely, but not to the point of running or puddling.

WARNING:

10. Replace the knife guard. Never leave the slicer without its knife gua rd installed.

11. Replace Knife deflector.

LUBRICATION

Lubrication instructions are given in Figure 2 on Page 7.
the slide bar (Figure 6 [4]) as needed for smooth carriage motion, but at least monthly with
drops of mineral oil.

Shafts to the last slice grip and to the auxiliary fence (Figure 5 [7,10]) (Figure 5A [8,12]

forth. Wipe excess petrogel, from shafts with a clean cloth.

PAGE 6

LUBRICATION INSTRUCTIONS

B OIL MONTHLY, THREE DROPS

MODEL 7510 - 7512 FIGURE 2

7510/7512

A PETROGEL, AS REQUIRED TO MAINTAIN
LIGHT FILM,

PAGE 7

MINERAL OIL.

TROUBLESHOOTING GUIDE

Motor running, blade

Product such as cheese old and

specified. Use care not to use

1

Clean knife and plastic scraper

Smearing or tearing

Knife dirty with hard dried on

Chill soft cheese for best slicing

7510/7512

TROUBLE POSSIBLE CAUSE REMEDY

7510/7512

1. Slicer will not

operate.

2.

not turning.

3. Slippage of knife

during slicing.

4. Motor stalls during

slicing.

1.1 Electrical service down.

1.2 Burned switch contacts.

1.3 Motor capacitor defective.

1.4 burned out motor

1.1 Check electrical service.
Replace fuse or reset circuit
breaker as necessary.

1.2 clean or replace.

1.3 replace.

1.4 Remove, test, repair or replace

2.1 Belt tension too tight 2.1 Readjust belt tension.
NOTE: Often after a long period of no use, such as in storage, the belt

flows and takes a set in the pulley ribs. A slight urging of the
knife with a wooden stick will get the slicer turning with no
further problems.

DO NOT USE HANDS TO TURN KNIFE.

3.1 Loose or broken belt.

3.2 Grease or oil on belt.

3.1 Adjust belt tension or replace

belt.

3.2 Clean pulleys with safety

approved cleaning solvent
on soft clean rag. Replace
belt.

4.1 Knife cutting edge to dull or

4.1 Sharpen using the procedure

improperly sharpened.

4.2

dried out.

4.3 Low voltage service.

4.4 Belt tension

excessive.

homing stone longer then the
or 2 seconds.

4.2 Reduce thickness of slice.

4.3 Have electrician check

service voltage.

4.4 Readjust belt tension.

5. Excessive noise. 5.1 Knife contacting the
knife guard.

5.2 Badly worn or frayed

belt.

5.3 Motor pulley and belt

misaligned.

5.4 Loose set screw in motor pulley

5.5 Dirty knife rubbin g against

plastic scraper

6.
when slicing soft
cheese.

6.1 Soft cheese is at room

temperatur e.

6.2

product.

5.1 Tighten knob which secures

guard.

5.2 Replace belt.

5.3 Realign motor pulley.

5.4 Tighten set screw.

5.5

6.1

results.

6.2 Clean knife thoroughly.

PAGE 8

7510/7512

tional tension is required, it may be obtained by turning

2. MOTOR:

Motor is pre

-

lubricated and requires no periodic maintenance or relubrication in normal kitchen

detergent oil may be

and turn

adjust its zero position, then tighten the two set screws. Actually, the

very slight lash or movement can be detected. Too much lash can result in the carriage striking and damaging

he knife edge. Too little lash results in binding and a loss of smoothness in carriage travel. Lash is adjusted

clockwise to reduce lash

during this lubrication sequence, be sure to check for free operation and

sharpening procedure, such as excessive honing, alert owner and operator.

MECHANIC'S MAINTENANCE

Every year a mechanic or service technician should perform the following inspection and carry out the respective
maintenance as required:

FOR SAFETY, TURN OFF SLICER AND DISCONNECT ELECTRICAL CORD.

1. BELT DRIVE: This drive features a multi-ribbed high performance belt for long trouble-free service. Inspect
belt for proper tension. If glazed or excessively worn, replace. A tensioning device automatically allows for

normal belt wear-in and stretching. However, if addi
adjustment nuts (Figure 9/10 [18]) clockwise on take up rod (Figure 9/10 [24]) which will further compress
the tensioning spring. As a guideline, the compressed length of the spring should be approx imately 7/8".

usage. Provision for re-lubrication in extreme duty applications is provided by means of oiling orifices at
both shaft end and opposite ends of motor. A light weight electric motor oil or #10 non­used.

3. SLICE ADJUSTMENT: Check, by turning the slice adjustment knob (Figure 3 (271) to make sure that the
fence is closing completely (below "0" on knob) and that knife edge is not exposed. If fence is not closing all

the way such that the edge of the knife is exposed, proceed to loosening the lock nut (Figure 7 [29])
the slice adjustment stop screw (Figure 7 [28]) so the knob can be turned further enough to allow the knife
edge to not be exposed. Now re-tighten the lock nut (Figure 7 [29]). Loosen the two set screws in the slice
adjustment knob (Figure 3 [26]) and re­closed or zero set position on the knob should be in the red colored zone of the knob's dial.

4. CARRIAGE: Check for free smooth operation of auxiliary fence, last slice device and for smooth travel of
carnage arm (Figure 6 [19]) Check for excess backlash between slice bearing (Figure 6 [ 14]) and carriage

slide (Figure 6 [7]). The correct lash (clearance) required for smooth carriage operation is obtained when a

t
by loosening locknut (Figure 6 [10]) and turning brass rubbing screw (Figure 6 [11])
and counterclockwise to increase lash. Tighten locknut while holding rubbing screw stationary with a
screwdriver so it does not move. Grease only the side of the carriage slide (Figure 6 [7]) on which this brass
rubbing screw slides.

5. LUBRICATION & FUNCTION CHECK: General lubrication should be performed in accordance with the
lubrication instructions in Figure 2.

movement of related parts as well as for excessive wear and looseness of various parts. Be sure to check all
handles and knobs for tightness.

6. KNIFE: Check knife edge to see that it has been properly sharpened. If there is any evidence of incorrect

PAGE 9

7510/7512

(including disassembly, replacement and reassembly.)

Always turn off slicer and disconnect electrical cord before doing any maintenance or repair on the slicer. Keep
guards on all times. Keep slice adjustment fully closed so knife edge is not exposed. Keep sharpener assembly also
in place so top of knife edge is not exposed.

DRIVE BELT

1. Disconnect electrical power cord.

2. Remove four rubber suction feet (Figure 3 [37]) that secure bottom cover (Figure 3 [36]) to slicer.

3. Remove nuts (Figure 9 [18]) from tensioning take-up rod (Figure 9 [24]) so motor can be pivoted to give belt
slack. Be careful not to lose tensioning spring (Figure 9 [19]).

4. Note the position of the belt on the pulley to insure proper installation of new belt.

5. Unwrap belt from motor pulley.

6. Reinstall rubber feet (Figure 3 [37]) and place slicer upright (operating position).

7. Loosen sharpener lock pin (Figure 3 [4]). Lift and remove sharpening unit. Set aside.

8. Remove knife guard knob (Figure 3 [2]) and carefully remove knife guard (Figure 3 [14]).

9. Using caution to avoid the sharp knife edge, remove the four screws (Figure 3 [12]) that secure the knife
Carefully remove knife and set aside with its flat side down, flush on a bench so the edge is not exposed.

10. Note the position of the belt on the pulley to insure proper installation of new belt.

11. Unwrap and remove drive belt from the knife pulley (Figure 3 [10]).

REPAIR INSTRUCTIONS

12. Wrap replacement belt on knife pulley and motor pulley. Do not reinstall knife at this time.

13. Reinstall spring and nuts on tensioning take up rod (Figure 9 [24]) and tighten. It is important to make sure
that the belt is aligned on both pulleys.

14. Belt tension is correct when the spring is compressed to an overall length of 7/8".

15. Connect electrical power and operate slicer to check that belt and pulleys are running true.

16. Disconnect electrical power cord.

17. Reinstall bottom cover and secure with the four suction feet.

18. Using caution, reinstall knife and secure with four screws.

19. Reinstall knife guard and secure with knife guard knob.

20. Reinstall sharpener and secure with lock pin.

PAGE 10

7510/7512

KNIFE (Removal Figure 3)

that secure knife

1. Disconnect electrical power cord.

2. Loosen sharpener lock pin (Figure 3 [4]), then lift and remove sharpening unit. Set aside.

3. Remove knife guard knob (Figure 3 [2]) and carefully remove knife guard (Figure 3 [14]).

4. Using caution to avoid the sharp knife edge, remove the four screws (Figure 3 [12])

(Figure 3 [15]).

5. Carefully remove knife and set aside with its flat side down flush on a bench so the edge is not

exposed.

6. Reinstall new knife in the reverse procedures outlined above.

7. Even though a new knife is very sharp, the sharpening procedure specified on pages 4 and 5 should

be performed to true the new knife's bevel to the slicer.

WARNING: Worn knife should be disposed of in a safe, responsible way, showing concern for other

KNIFE SEAL (Figure 31

1.

Remove knife per above instruction.

2. Unscrew and remove knife insert stud (Figure 3 [16]). Maintain shims that may have been used in

assembly.

3. Using a small screwdriver, carefully pry and remove the knife seal (Figure 3 [11]) from the knife

pulley (Figure 3 [10]).

4. Apply light film of mineral oil on outer diameter and lip of rubber seal.

5. Clean recess in pulley.

6. Drive seal into recess in pulley using care to avoid damage to seal. Seal should be seated uniformly.

7. Check knife insert stud (Figure 3 [16]) for small sharp burrs that may have been raised during its

removal. Remove burrs if present with a fine-toothed file. If burrs are not removed, they will destroy
the seal very quickly.

9. Reinstall knife insert stud and shims that may have been present. Apply three drops of mineral oil to

the seal/stud interface.

11. Reinstall knife, guard and sharpener in the reverse procedure outlined above.

who may handle it. It is recommended that the edge of the knife be wrapped several time
with heavy tape and that a caution (CAUTION, SHARP EDGE) be written on both sides
of the knife.

PAGE 11

7510/7512

SHARPENING STONES

1. Disconnect electrical cord.

2. Unscrew sharpener lock pin (Figure 3 [4]).

3. Lift up sharpening assembly (Figure 1 [6]) and remove from slicer.

4. Using an open end wrench, unscrew cover knob (Figure 4 [1]). It is recommended that a piece of tape or paper

be temporarily wrapped around knob prior to unscrewing it so as to protect its finish.

5. Gently remove lever cover (Figure 4 [2]) off of mounting block (Figure 4 [26]). Perform this step slowly taking

care to remove cover evenly from the two locating pins (Figure 4 [9]) on which it fits snugly.

6. Unscrew nut (Figure 4 [21]) and remove along with washer and sharpening stone (Figure 4 [23]).

7. Install new sharpening stone. Flat face should be toward the outside.

8. Re-attach washer and nut.

9. Honing (deburring) stone (Figure 4 [14]) is removed by first unscrewing lock screw (Figure 4 [19]) from

thimble (Figure 4 [18]).

10. Gently remove thimble taking care to not lose the small ball bearing and spring (Figure 4 [16 & 17]) which are

inside.

11. Unscrew nut (Figure 4 [15]) and remove along with washer and honing stone (Figure 4 [14 & 20]).

12. Install new honing stone with the flat face toward the inside.

13, Re-attach washer, nut, and thimble.

14. Re-attach cover and reinstall in the reverse procedures (5. through 1,).

REPLACEMENT OF PARTS LISTS

Replacement parts for the Food Slicing Machine are shown in the following Figures. When ordering replacement
parts, always include the model and serial numbers of the machine in addition to the specific part number.

PAGE 12

7510/7512

BASE AND KNIFE HOUSING ASSEMBLY

MODEL 7510 - 7512

FIGURE 3

ILLUS. NO. PART NO. DESCRIPTION QTY.

1. 7510012 WASHER, KNIFE 1

2. 7510015 KNOB, KNIFE GUARD 1

3. 7510013 NUT KNIFE 1

4. 7510150 LOCK PIN, SHARPENER 1

5. 7510001 BACK KNIFE GUARD (MODEL 7510) 1
7512001 BACK KNIFE GUARD (MODEL 7512) 1

6. 7510156 WASHER, KNIFE SHIM AS REQ;

7. 7510002 SHAFT, KNIFE 1

8. 7510158 WASHER, KNIFE SHIM AS REQ.

9. 7510004 SPACER 1

10. 7510154 PULLEY, KNIFE 1

11. 6509012 BUSHING, KNIFE 1

12. 6509014 SCREW, BLADE 3

13. 8512240 SCRAPER, BLADE 4

14. 7510011 KNIFE GUARD (MODEL 7510) 1
7512011 KNIFE GUARD (MODEL 7512) 1

15. 7510009 BLADE (MODEL 7510) 1
7512009 BLADE (MODEL 7512) 1

16. 7510008 INSERT, KNIFE 7510 1
7512008 INSERT, KNIFE 7512 1

17. 1012167 BALL BEARING 2

18.

RESERVED

19. 7510022 KNIFE DEFLECTOR 1

20. 8512206 LOCATING PIN 1

21. 7510023 KNIFE DEFLECTOR SCREW 1

22. 7510019 SLICER BODY 1

23. 8512208 GRADUATED KNOB BUSHING 1

24. 8512210 FRONT WHEEL 1

25. 6509098 SET SCREW 1

26. 8512214 SET SCREW 2

27. 7510084 GRADUATED KNOB 1

28. 8512211 REAR WHEEL 1

29. 8512209 RIVET 2

30. 7120009 ON-OFF SWITCH 1

31. 7120009 SWITCH JAM NUT (PART OF SWITCH)

32. 7120011 SWITCH GUARD 1

33. 7120009 SWITCH JAM NUT (PART OF SWITCH)

34. 7120014 INDICATOR LIGHT 115V 1
7120041 INDICATOR LIGHT 220V 1

35. 4400081 SCREW, DOME DRIVE, NO.6 X 5/16 1

36. 7120026 BOTTOM COVER 1
7120126 BOTTOM COVER, 100 V ONLY 1

37. 7510094 RUBBER SUCTION FEET 4

38. 7510014 KNIFE GUARD SHAFT 1

39. 7510021 WASHER, FLAT 2

40. 8512525 LOCK WASHER, EXTERNAL TOOTH M10 2

41. 7510020 SCREW, HEX SOCKET HD M10-1.25 X 25MM 2

42. 7120130 SPACER 100 V ONLY 4

43. 8512326 STUD 100V ONLY 4

44. 4400338 LABEL, DURO (NOT SHOWN) 1

PAGE 13

7510/7512

BASE AND KNIFE HOUSING ASSEMBLY

MODEL 7510 - 7512

FIGURE 3

PAGE 14

7510/7512

SHARPENER ASSEMBLY

MODEL 7510 - 7512

FIGURE 4

ILLUS NO. PART NO. DESCRIPTION QTY.

7510151A SHARPENER ASSEMBLY WITH CONER
1 6509153 KNOB, COVER 1
2 6509151 COVER, SHARPENER 1
3 6509150 NUT, COVER SPACER 1
4 6509149 SPACER. COVER 1
5 6509125 WASHER, SET PIN 1
6 6509137 SCREW 1
7

RESERVED
8 7510120 SET PIN, SHARPENER 1
9 8512728 PIN, SHARPENER CASTING 2

10 6509147 BOLT, SHARPENER GUIDE 2
11 6509127 SPRING 2
12 6509128 BUSHING 2
13 6509129 STUD, HONING STONE 1
14 6509130 STONE, HONING 1
15 6509131 NUT 1
16 6509134 SPRING 2
17 6509133 BALL 2
18 6509135 BUTTON, DEPRESS 2
19 6509136 SET SCREW, DEPRESS BUTTON 2
20 6509132 WASHER, HONING STONE 1
21 6509143 NUT, SHARPENING STONE 1
22 8512516 WASHER, SHARPENING STONE 1
23 6509142 STONE, SHARPENING 1
24 6509141 STUD, SHARPENING STONE 1
25 6509126A MOUNT, STONE 1

PAGE 15

7510/7512

CARRIAGE ASSEMBLY

MODEL 7510

FIGURE 5

ILLUS. NO. PART NO. DESCRIPTION QTY.

1. 8512432 SPACER, ADJUSTMENT 1

2. 8512436 STUD, ADJUSTMENT SPACER 1

3. 6509153 KNOB 3

4. 8512433* BUSHING ADJUSTMENT SPACER 2

5. 8512426 LAST SLICE DEVICE 1

6. 6509054 KNOB, LAST SLICE DEVICE 1

7. 8512428 SHAFT, LAST SLICE DEVICE 1

8. 8512427** BUSHING, LAST SLICE DEVICE 2

9. 8512425 CARRIAGE 1

10. 8512434 SHAFT, ADJUSTMENT SPACER 1

11. 8512431 NYLON TIP 2

12. 6509059 WASHER 1

13. 6509058 BOX NUT 1

14. 1200079 LOCKWASHER 1

15. 8512439 CARRIAGE STUD SCREW 1

16. 8512438 NYLON TIP 1
* Illus 4, 8512433 cannot be purchased separately it is part of illus 1,8512432.
** Illus 8, 8512427 cannot be purchased separately it is part of illus 5, 8512426.

PAGE 16

CARRIAGE ASSEMBLY

ILLUS. NO.

PART NO.

DESCRIPTION

QTY. 1. 8512432

SPACER, ADJUSTMENT

1

9. 8512427**

BUSHING, LAST SLICE DEVICE

1

1

1

1

1

1

1

1

1

19. 6509057

STUD, CARRIAGE

1

* Illus 4,

851

2433

cannot be purchased separately it is part of illus

1, 8512432.

** Illus

9, 8512427

cannot be purchased separately it is part of .illus

5, 8512925.

MODEL 7512

FIGURE 5A

2. 8512436 STUD, ADJUSTMENT SPACER 1

3. 6509153 KNOB 3

4. 8512433* BUSHING ADJUSTMENT SPACER 2

5. 8512925 SUPPORT, LAST SLICE DEVICE 1

6. 8512924 KNOB, LAST SLICE DEVICE 1

7. 8512926 LAST SLICE DEVICE 1

8. 8512428 SHAFT, LAST SLICE DEVICE 2

10. 8512425 CARRIAGE

11. 8512438 NYLON TIP, ADJUSTMENT SPACER

12. 8512434 SHAFT, ADJUSTMENT SPACER

13. 8512431 NYLON TIP, LAST SLICE DEVICE

14. 8512927 STUD, CARRIAGE

15. 8512229 SCREW, FLAT HEAD

16. 6509058 BOX NUT, M10-1.5

17. 1200079 LOCKWASHER

18. 8512439 WASHER, SPECIAL 1

7510/7512

PAGE 17

7510/7512

HANDLE, CARRIAGE ARM

CARRIAGE ARM AND SLIDE ASSEMBLY

MODEL 7510 - 7512

FIGURE 6

ILLUS. NO. PART NO. DESCRIPTION QTY.

1. 6509036 WASHER, SLIDE BAR RUBBER 2

2. 7510337. SPRING, SLIDE BAR (7512 ONLY) 2
6509035 SPRING, SLIDE BAR (7510 ONLY) 2

3. 8512229 SCREW, M5-0.8 X 12MM FL HD SLT 2

4. 7510434 BAR, CARRIAGE SLIDE 1

5. 7510326** BUSHING, CARRIAGE ARM 2

6. 7510325 SUPPORT, CARRIAGE ARM 1

7. 7510339 SLIDE, CARRIAGE 1

8. 6509041 WASHER, CARRIAGE SLIDE 2

9. 6509040 BOLT, CARRIAGE SLIDE 2

10. 9512299 BUSHING ECCENTRIC 1

11. 1053510 SCREW, CAP M6-1.0 X 25MM HX HD 1

12. 8512308 SCREW, BEARING LOCKING 1

13. 6509028 WASHER, M8 2

14. 6509031 BEARING 2

15.

16.

RESERVED
RESERVED

17. 6509037 WASHER 2

18. 6509042 BOLT, CARRIAGE 1

19. 7510043 CARRIAGE ARM 1

20. 6509044 KNOB, CARRIAGE ARM 1

21. 6509045

22. 6509046 SCREW, CARRIAGE ARM HANDLE 2

23. 8512325 ANCHOR, CARRIAGE 1

24. 8512326 STUD, CARRIAGE ANCHOR 1

** Illus, 5 7510326 cannot be purchased separately it is pan of illus 6, 7510325.

1

PAGE 18

7510/7512

SLICE ADJUSTMENT ASSEMBLY

MODEL 7510 - 7512

FIGURE 7

ILLUS. NO. PART NO. DESCRIPTION QTY.

1. 7510067 SCREW, SLICE CONTROL ATTACHMENT 2

2. 8512527 SCREW, SLICE CONTROL ATTACHMENT 1

3. 8512526 JIB 1

4. 8512525 WASHER, TOOTHED 2

5. 7510065 SCREW, JIB ATTACHMENT 2

6. 7512076 BOLT, TAPER SUPPORT (7512 ONLY) 1
7510076 BOLT, TAPER SUPPORT (7510 ONLY) 1

7. 8512839 NUT 2

8. 8512522 WASHER 1

9. 6509071 STUD, CRANK 1

10. 8512511 BLOCK, SLICE ADJUSTMENT MOVING 1

11. 8512512 SHAFT, SLICE CONTROL 1

12. 7510073 STUD, JIB ATTACHMENT 1

13. 8512326 STUD 1

14. 6509131 NUT 1

15. 7510061 SPRING 1

16. 8512518 SCREW, SPRING ATTACHMENT 1

17. 6509028 WASHER 2

18. 8512501 PIN, ECCENTRIC 1

19. 8512502 GEAR 1

20. 8512503 WASHER 1

21. 8512504 SCREW, GEAR ATTACHMENT 1

22. 8512510 SHAFT, GRADUATED KNOB 1

23. 6509086 WASHER, FLEXIBLE 1

24. 8512507 WORM GEAR 1

25. 8512506 BALL 1

26. 8512508 ROLL PIN 1

27. 8512505 BALL STUD 1

28. 8512529 SCREW, SLICE ADJUSTMENT STOP 1

29. 8512530 NUT 1

30. 7510060 SLICE CONTROL GUIDE UNIT 1

PAGE 19

7510/7512

FENCE ASSEMBLY

MODEL 7510 - 7512

FIGURE 8

ILLUS. NO PART NO. DESCRIPTION QTY.

1. 7510079 FENCE (MODEL 7510) 1

7512079 FENCE (MODEL 7512) 1

2.

SHIMS AS REQ

3. 1200300 ROLL PIN 3/16 X 2 1

4. 7510077 BRACKET, FENCE MOUNTING (MODEL 7510) 1

7512077 BRACKET, FENCE MOUNTING (MODEL 7512) 1

5. 8512326 SET SCREW 1

6. 6509081 NUT, ACORN 2

7 6509082 WASHER 2

8. 6509080 STUD, FENCE 2

PAGE 20

7510/7512

MOTOR. MOUNT AND DRIVE ASSEMBLY

MODEL 7510 - 7512

(115V, 50/60HZ, 1PH) (100V, 50/60HZ, 1PH)

FIGURE 9

ILLUS. NO. PART NO. DESCRIPTION QTY.

1. 6090000 MOTOR, 1/3 HP, 115V, 50/60HZ, 1PH 1

2. 4400085 TUBING, CORD 15 FT

3. 1200076 WASHER NO. 10 11

4. 7120034 BRACKET, LEFT 1

5. 4400183 LOCKWASHER N0.8 4

6. 1200058 NUT 8-32 5

7. 7510099 BOLT, MOTOR PIVOT 10.MM SPECIAL 1

8. 7120006 SPACER 2

9. 7510157 BRACKET, MOTOR PIVOT 1

10. 1200261 LOCK WASHER 2

11. 1200260 SCREW, SOCKET HD. CAP 2

12. 4400127 WASHER, RUBBER 1

13. 7120033 BRACKET, RIGHT 1

14. 7510252 NUT, 10MM ELAS STOP 1

15. 7512155 BELT, POLY RIB (7512 ONLY) 1
7510153 BELT, POLY RIB (7510 ONLY) 1

16. 6509156 PULLEY, MOTOR 1

17. 6509098 SET SCREW 1

18. 1200060 NUT, JAM 10-32 2

19. 6509104 SPRING 1

20. 7120022 BRACKET, BELT TENSION 1

21.* 6509041 WASHER, CARRIAGE SLIDE 1

22.* 6509040 BOLT, CARRIAGE SLID 1

23. 4400188 GROMMET, RUBBER 1

24. 4400023 ROD, BELT TENSIONING 1

FOR 115V, 50/60HZ, 1PH ONLY

SEE FIGURE 8A FOR 100V, 50/60HZ, 1PH

3. 1200076 WASHER NO. 10 4

25. 4400065 LOCK WASHER NO. 10 1

26. 7120017 NUT M5-0.8 5

27. 4400101 CLAMP, CABLE 1

28. 4400053 CORD, ELECTRIC 1

29. 1012042 STRAIN RELIEF 1

30. 7120001 CAPACITOR - 20 MFD., 370V. 1

31. 4400024 CLAMP, CAPACITOR 1

32. 7120008 BOOT, CAPACITOR 1

33. 6509113 STUD, M5-0.8 X 40MM 2

34. 6509161 STUD, M5-0.8 X 25MM 1

FOR CANADA ONLY

35. 4400240 CIRCUIT BREAKER 3.5 .AMP 1

36. 4400227 LABEL, RESET 1

* ILLUS NO. 21 & 22 ARE SAME PART AS ILLUS NO. 8 & 9 IN FIGURE 6

PAGE 21

7510/7512

MOTOR. MOUNT AND DRIVE ASSEMBLY

MODEL 7510 - 7512

(115V, 50/60HZ, 1PH) (100V, 50/60HZ, 1PH)

FIGURE 9

PAGE 22

TRANSFORMER / CAPACITOR PANEL

1

1

1

1

1

1

2

1

1

100V,50/60HZ,1PH

FIGURE 9A

7510/7512

ILLUS. NO. PART NO. DESCRIPTION

3 1200076 WASHER, NO. 10 8
12 4400191 WASHER, RUBBER 4
25 4400065 WASHER, LOCK NO. 10 5
26 7120017 NUT, M5-0.8 4
27 4400101 CLAMP, CABLE
28 4400053 CORD, ELECTRICAL
29 1212042 STRAIN, RELIEF
30 7120001 CAPACITOR, 20MFD, 370V, 50/60HZ, 115V
31 4400024 BRACKET, CAPACITOR
32 7120008 BOOT, CAPACITOR
33 6509113 STUD. M5-0.8 X 40MM
34 6509161 STUD. M5-0.8 X 20MM
35 7100117 TRANSFORMER
36 1200060 NUT, HEX 10-32 7
37 7100118 BRACKET, TRANSFORMER / CAPACITOR 1
38 400414 WASHER, FENDER 1/4 ID 2
39 200012 SCREW, PPHD 10-32 X 1/2 4

QTY

PAGE 23

7510/7512

1

1

1

1

1

1

1

1

1

1

1

1

1

3

1

1

1

1

MOTOR. MOUNT AND DRIVE ASSEMBLY

MODEL 7510 - 7512 220-240V, 50/60HZ, 1PH

FIGURE 10

ILLUS. NO. PART NO. DESCRIPTION QTY.

1. 6090002 MOTOR 1/3HP, 220-240V, 50/60HZ, 1PH 1

2. 4400085 TUBING, CORD 1.5FT

3. 1200076 WASHER NO. 10 2

4. 7120034 BRACKET, LEFT 1

5. 4400183 LOCKWASHER NO. 8 1

6. 1200058 NUT 8-32 2

7. 7510099 BOLT, MOTOR PIVOT 10.MM SPECIAL 1

8. 7120006 SPACER 2

9. 7510157 BRACKET, MOTOR PIVOT 1

10. 4400005 LOCK WASHER 2

11. 7510251 SCREW, SOCKET HD. CAP 2

12. 4400127 WASHER, RUBBER 1

13. 7120033 BRACKET, RIGHT

14. 7510252 NUT, 10MM ELAS STOP

15. 7512155 BELT, POLY RIB (7512 ONLY)
7510153 BELT, POLY RIB (7510 ONLY)

16. 6509156 PULLEY, MOTOR

17. 6509098 SET SCREW

18. 1200060 JAM NUT 10-32 2

19 6509104 SPRING

20. 7120022 BRACKET, BELT TENSION

21.* 6509041 WASHER, CARRIAGE SLIDE

22.* 6509040 BOLT, CARRIAGE SLID

23. 4400188 GROMMET, RUBBER

24. 4400023 ROD, BELT TENSIONING

25. 4400065 LOCK WASHER NO. 10

26. 7120017 NUT M5

27. 4400101 CLAMP, CABLE

28. 8800210 CORD. ELECTRIC

29. 1012042 STRAIN RELIEF

30 6509161 STUD, M5-0.8 X 25MM

* ILLUS NO. 21 & 22 ARE SAME PART AS ILLUS NO. 8 & 9 IN FIGURE 6

PAGE 24

7510/7512

MOTOR. MOUNT AND DRIVE ASSEMBLY

MODEL 7510 - 7512

220-240V, 50/60HZ, 1PH

Figure 10

PAGE 25

7510/7512

CAPACITOR PANEL 220-

240V, 50/60HZ, 1PH

Figure. 10A

ILLUS. NO. PART NO. DESCRIPTION QTY.

1 7120052 PANEL, CAPACITOR 1
2 1200076 WASHER, FLAT NO. 10 8
3 1200415 SCREW, HEX HD 10-32 X 1 1/4 4
4 6509113 STUD, M5-0.8 X 40MM 3
5 1200430 WASHER, LOCK N0.6 2
6 1200429 NUT, HEX 6-32 2
7 1814062 WASHER, FLAT M5 3
8 4400065 WASHER, LOCK NO. 10 3

9 7120017 NUT, HEX M5-0.8 3
10 7120055 RELAY 1
11 1200093 WASHER, FLAT N0.6 2
12 4400204 SCREW, PAN HD 6-32 2
13 7120051 CAPACITOR, 5UF, 370V, 50/60HZ. 1
14 7120056 CAPACITOR / RESISTER 100K 1
15 7120008 BOOT, CAPACITOR 2
16 1200060 NUT, HEX 10-32 4
17 4400224 BRACKET, CAPACITOR 220V 2

PAGE 26

WIRING DIAGRAM

MODEL 7510 - 7512

115V, 50/60 HZ, 1PH

FIGURE 11

7510/7512

IMPORTANT
Before making electrical connections, check the specifications on the data plate to assure they agree

with those of your electrical service.
Whenever cleaning or maintenance is being performed DISCONNECT electrical cord.

PAGE 27

WIRING DIAGRAM
MODEL 7510 - 7512

220-240V, 50/60HZ, 1PH

FIGURE 11A

7510/7512

IMPORTANT
Before making electrical connections, check the specifications on the data plate to assure they agree

with those of your electrical service.

Whenever cleaning or maintenance is being performed DISCONNECT electrical cord.

PAGE 28

WIRING DIAGRAM
MODEL 7510 - 7512
100V, 50/60HZ, 1PH

FIGURE 11B

7510/7512

* CAUTION: Installations with 50HZ electrical supplies should have black motor lead connected to
110V output terminal ONLY. Connection to higher voltage outputs could cause motor failure. The
transformer has been wired at the factory for 50HZ operation at 110V output. If you have 60HZ
electrical supply the black motor lead can be switched to 115V output terminal for optimal slicer
performance.

* * The black motor lead should ONLY be connected to 120V output when the supply voltage is
consistently at 90V or less (50 or 60HZ).

IMPORTANT
Before making electrical connections, check the specifications on the data plate to assure they agree

with those of your electrical service
Whenever cleaning or maintenance is being performed DISCONNECT electrical cord.

PAGE 29