Universal Wireless Solutions Oracle Quick Setup Manual

Oracle limited LIFETIME WARRANTY

International Electronics Inc. (IEI) warrants this product to be free of defects in materials and workmanship, for its usable
lifetime. For a period of ONE YEAR following purchase, IEI will repair or replace the product free of charge, including parts,
labor, return shipping to you, and handling.

All repairs or replacements are at the discretion of the Manufacturer. This warranty excludes items that have been abused,
altered, incorrectly installed, or repaired by an unauthorized person. Changes or modifications not expressly approved by the
Manufacturer could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to
operate the equipment. This warranty is limited to the product only. No consequential damages are covered.

After the initial one year of operation, the limited lifetime warranty will cover parts, labor, and return shipping to you, with a
minimal handling charge specific to the product, as listed below:

Oracle Portable Intercom: $30.00

If you have installation or operation questions or are in need of warranty service, please contact our Product Support department
by email at [e-mail] or call 360-254-1564 Tuesday-Friday 7-5 Pacific Time. If the issue is not resolvable, a
manufacturer’s warranty repair order may be issued. To have the product(s) sent for warranty service. A Return Authorization
number will be issued for warranty service, which must be put on the outside of the package, to be received and handled
properly. Packages for warranty service may be sent to the following address. Packages with no RA# may not be accepted.

IEI

5913C NE 127th AVE, Suite 800

Vancouver, WA 98682

Please include a note describing the problem that you are having and a copy of your original sales receipt (within the first year).
If the warranty service is outside the first year, please include a check made out to IEI, based on the list of handling fees, shown
above. Please note that you may need to send multiple units for warranty service, testing, and upgrading, though only the
applicable fee for handling the failed unit(s) will be charged.
Please allow 2-4 weeks for service and return shipping. If an EXPEDITED repair/replacement is requested, a 100% surcharge
applies. In this case, please write EXPEDITED after the RA number. IEI will attempt to return expedited repair orders within
one week, except during holidays

Multiple Uses Include…

• Garage or Workshop

• Between Offices

• Back Porch or Pool

• Camping or Hunting

• Temporary Work Locations

• Oracle Gate System Compatibility

• Home O

ffice

• Motor Home or Guest Room

• Network Wide Conference Mode

Thank you for purchasing
the Reporter Wirefree
Intercom. This product has
been designed and
manufactured in the USA,
utilizing the highest quality
standards available.

Model# OPI-605.

Ver.

03/29/07

P

atents pending

With the Reporter Oracle
Portable Intercom, you can
talk up to 1000 feet,
completely wire free with a
900 MHz secure digital radio
link.

For privacy, your intercoms
form an exclusive network,
and respond only to other
intercoms in your network.

(Patent Pending)

Even conversations within
your network are secure, as
intercoms automatically pair
up, blocking all other
intercoms from listening in.

The Portable Intercom is
compatibl

e with other Oracle
Intercom units as well as the
Oracle Gate System.

Please read the instructions

carefully.

TM

Port^ble Intercom

Made With Pride In the USA. This product is covered by a

manufacturer’s full One Year Warranty.

FCC STATEMENT

This device complies with FCC part 15 rules. It may not cause harmful interference with other devices, and must accept interference from other devices.

FCC ID: JLFTRX

INTERCOM QUICK SETUP GUIDE

1) Remove the battery door from the bottom of each unit and place four fresh AA

Alkaline batteries in the battery pack. Use premium batteries for best
performance. Once the batteries are installed, the channel lights will begin to
flash in sequence.

2) To create an Intercom Network, stand the antennas up, then Press the LEARN
button for 1 second on each intercom. Note: all LEARN buttons must be
pressed within ten seconds of each other. The units will beep as they join the
Network. Additional Intercoms may be added to the network at any time by
pressing the LEARN button on one of the networked units and on the new unit.

3) Press and release the TALK button on an Intercom unit to verify that the
network is complete.

Using the Intercom

To talk, hold down the TALK button. All
intercom units in your network will receive
the signal. When somebody responds by
holding down the TALK button on a different
intercom unit, a secure channel is created
and other units will not hear the signal,
making your conversation secure.

Channel Selection

The default setting for the intercom is
Paging Mode, with all four Channel lights
flashing in sequence. Pressing the CHANNEL
button will set an intercom unit to one of four
secure channels. While on a channel, you can
only be heard by other units set to the same
channel or in paging mode.

Adjusting the speaker volume

Press the VOLUME button repeatedly to cycle
through the three volume levels.

Turning the intercom On or Off

An intercom may be turned off by holding
down the VOLUME button for five seconds. To
turn it back on, press any button.

Conference Mode

To put an intercom unit in Conference
mode, slide dipswitch #2 UP. This will
allow any number of units to join a
conversation, not just two.

Batteries

With average use, the batteries will last
up to one year

A double beep every

ten minutes will alert you that the
batteries are getting low.
If desired, the Intercom may also be
powered by a 12-volt DC transformer
(commonly available in most department
stores). In this case, both the power and
channel lights will remain on constantly.

Oracle System Compatibility

If you receive a CALL from the Oracle
Gate System, the Portable intercom Alert
light will illuminate as it chimes. The
CHANNEL/REMOTE button will open the
gate. See the Oracle Gate System manual
for complete information.

Portable Intercom Settings

Portable Intercom units are intended to
be an add-on accessory with limited
function and can only control the Primary
Gate Controller (#1). The default setting
is ON (towards the circuit board). OFF
(open) is away from the circuit board.

− sw1 is ON to disable Gate Status
Checking and OFF to display Gate
Status.

− sw2 is ON for secure mode, OFF
for intercom conference mode

DC Transformer LEARN button

Channel Select

Talk

(Power-ON,)

Volume/Sensitivity

(Power-OFF)

Radio Frequency Test Feature

When used with the Oracle PRO Gate Access Panel (GAP), you can test the quality of the
radio channel that units are transmitting on. Activate the oracle Pro units as normal and
enter the master PIN code, and then 01 on the keypad. The GAP will emit a number of
beeps as it tests the frequency, and then give a double-beep when it’s ready to report
the test results. The result will be 1-10 beeps, indicating the signal quality, with 6-10
beeps indicating an acceptable connection. To correct for unacceptable signal quality,
add repeaters, and/or move the units closer together.

Troubleshooting and Frequently Asked Questions

My intercom does nothing. What should I do?

If there are no lights illuminated, make sure four fresh AA alkaline batteries are all
installed correctly. The CHANNEL lights should flash. If you are using the optional
12-volt transformer, make sure it is plugged in. The POWER and CHANNEL lights
should be continuously on. If not, try another outlet.
If the units have power but do not communicate, they may need to form a network.
Press the LEARN button on each unit that needs to form a network and they will beep
in response. You may need to clear their memory and re-teach them (see Removing
from a Network, below).
If the units do not have the same channel light flashing, press the CHANNEL button
until both units are on the same channel or in Paging mode, with all channel lights
illuminated.

How do I Remove an Intercom from a Network?

Press and hold the Learn button, for fifteen seconds. It will beep when it has
cleared its memory and you can re-teach it to a new intercom. If an intercom signals,
while the Learn button is depressed, the procedure will have to be repeated.

Why is the intercom not getting the expected 1000 foot range?

To assure best range, make sure that the intercom unit’s antenna is VERTICAL. Cell
phones, cordless phones, or other radio devices may reduce the intercom’s range if
they are within a few feet of an intercom. Trees, metal, electrical wiring or other
electrical devices directly between units may also limit the range.

Why is there a double beep every ten minutes?

The intercom is indicating that the batteries are low and need to be replaced.

How do I use the Portable Intercom with Oracle Repeaters?

When using Oracle Repeaters to extend the range of an Oracle network, be sure to
clear the memory of the Portable Intercom by holding down the LEARN button for
15 seconds, before teaching it to the Repeater.

What kind of Wall Transformer can I use to Power my Intercom?

The Wirefree intercom is optimized for high quality AA batteries, but it may be
powered by an 9-12 volt, 500mA, DC transformer purchased separately (center­positive polarity on the round plug) like Radio Shack’s

12V/500mA AC-to-DC Power

Adapter

.