Description
The Universal Tool Superhand Air File is designed to file small areas with restricted
access with ease. This reciprocating air file weighs just over two pounds for easy
one-handed operation. Features include a hanging bail for easier handling, a
thumb switch throttle for easy start-up, and a durable steel housing. Able to file
steel, plastic, wood and aluminum. It’s 1/4” stroke length makes quick work of most
jobs. Includes 4 assorted files: flat, round, triangular and bastard cut.
UT8862
SUPERHAND AIR FILE
PLEASE READ AND FOLLOW ALL WARNINGS
Read Operating Instructions
Always become familiar with all the
instructions and warnings before
operating any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection
should meet or exceed the
standards as set forth in the United
States ANSI Z87.1, Occupational
and Educational Eye and Face
Protection. Look for the marking
Z87.1 on your eye protection to
insure that it is an approved style.
For further information, ANSI Z87.1,
Occupational and Educational Eye
and Face Protection, is available
from the American National
Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used
when the noise level exposure
equals or exceeds an 8 hour timeweighted average sound level of 85
dBA. Process noise, reflective
surfaces, other tools being
operated nearby, all add to the
noise level present in your work
area. If you are unable to determine
your noise level exposure, we
recommend the use of hearing
protection.
Avoid Prolonged Exposure to
Vibration
Tools can vibrate during use.
Prolonged exposure to vibration or
very repetitive hand and arm
movements, can cause injury. Stop
using any tool if discomfort, tingling
feeling or pain occurs. You should
consult your physician before
resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at
an air pressure of 90 pounds per
square inch gauge pressure (90
PSIG) maximum, at the tool. Use of
higher air pressure can, and may
cause injury. Also, the use of
higher air pressure places the
internal components under loads
and stresses they were not
designed for, causing premature
failure. The air supply should be
clean and dry, preferably
lubricated. For best results, drain
the moisture from your compressor
daily.
PL-0258
Universal Tool
A Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate
or service this Florida Pneumatic product. Failure to comply with the
instructions could result in personal injury and/or property damage!
Retain these instructions for future reference.
Safety Instructions
The following instructions are furnished
as general guidelines for use of your
pneumatic tool. They cannot comprehensively cover all possible or conceivable uses of the subject tool. For
additional information on the safe use
of air tools, we advise you to obtain a
copy of ANSI B186.1 Safety Code for
Portable Air Tools, available from the
following source:
American National Standards
Institute, Inc.
11 West 42nd Street
New York, NY 10036.
The use of the word “shall” in the
following instructions, indicates that
adherence to the particular requirement is necessary to conform to ANSI
B186.1.
Tool Application and Usage
Portable tools shall be used only for
the purposes intended in their design
and within the capacity for which they
were intended and rated. It shall be
the tool owner’s and/or employer’s
responsibility to instruct each operator
in the safe use of the tool. Tools shall
not be used without guards and safety
devices as furnished by the manufacturer. Where an air tool is modified or
altered, the modifier shall provide the
safeguards to enable it to be safely used
in the operations intended and to comply
with any applicable provisions as
contained in ANSI B186.1.
Tool Installation
Pressure regulators shall be used to limit
air pressure to the rated pressure where
the supply pressure exceeds the tool’s
rated pressure. Air hoses and lines shall
be relieved of compressed air before
being disconnected or disjointed, unless
there is automatic valve closing protection at the joint being separated. Synthetic lubricants which can cause
deterioration of elastomer seals shall not
be used in air systems of air tools.
Tool Maintenance
It shall be the tool owner’s and/or
employer’s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools shall
be disconnected from their compressed
air supply before repairs are attempted.
Repairs shall be consistent with the
manufacturer’s recommended procedures. Tool, hoses and fittings shall be
replaced if unsuitable for safe operation.
It shall be the tool owner’s and/or
employer’s responsibility to keep required
rating markings and warnings on the tool
in legible condition.
FPMC
Rev. 8/98
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth
defects or reproductive harm. Some examples
of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement and
other masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals, work in a well-ventilated area and
work with approved safety equipment such as
those dust masks that are specially designed to
filter out microscopic particles.
UT8862
SUPERHAND AIR FILE
Parts Breakdown for UT8862
UT8862
SUPERHAND AIR FILE
Ref. Description Part #
Ref. Description Part #
1 Housing 9705001
2 Spring (2) 9705002
3 Filter 9705003
4 Retaining ring 9705004
5 Cap 9705005
6 Guide key 9705006
7 Hangar 9705007
8 Cylinder assembly (9-13) 9705008
9 Spring pin 9705009
10 Plug 9705010
11 Headless set screw 9705011
12 Cylinder 9705012
13 Piston 9705013
Universal Tool’s Limited Warranty
Universal Tool warrants their tools to be free from defects in material and workmanship
for one year from the date of purchase. This warranty does not apply to tools which
have been abused, misused, modified or repaired by someone other than Universal
Tool or their authorized service centers. If a Universal Tool tool proves defective in
material or workmanship within one year after purchase, return it to any authorized
service center or Universal Tool freight prepaid. Please enclose your name, address
and adequate proof of purchase and a short description of the defect. Universal Tool
will, at their option, repair or replace defective tools, free of charge. Repairs or
replacements are warranted as described above for the remainder of the original
warranty period. Universal Tool’s sole liability and your exclusive remedy under this
warranty is limited to repair or replacement of the defective tool. There are no other
warranties expressed or implied and Universal Tool shall not be liable for incidental,
consequential or special damages, or any other damages, costs or expense of repair
or replacement as described above.
Specifications
Replacement Parts for UT8862
File Size ................................................................................................. 4” x 1/4” Round Shaft
Free Speed ............................................................................................................... 9,000 SPM
Stroke length ....................................................................................................................... 1/4”
Weight ..........................................................................................................................2-1/4 lbs.
Length ......................................................................................................................................7”
Average air consumption .............................................................................................. 4 CFM
Recommended hose size .............................................................................................. 3/8” ID
Air inlet ........................................................................................................................ 1/4” NPT
Maximum operating pressure .....................................................................................90 PSIG
14 Valve nipple 9705014
15 Valve nipple ass’y (14,16) 9705015
16 O-Ring 9705016
17 Valve assembly 9705018
18 Valve body 9705019
19 O-Ring (2) 9705020
20 3mm Hex wrench 9705021
21 Hose assembly 9705022
22 3 Pk of Flat Mill Cut Files 5679
23 3 Pk of Round Single Cut 5680
24 3 Pk of Triangle Single Cut 5681
25 3 Pk of Flat Bastard Cut 5682
* 4 Pk Asstd. (1 ea. above*) 5683
- Always wear eye protection during use.
- Do not use excessive force while filing.
Loading...