Universal Tool UT8701, UT8893-60S, UT8719, UT8719K, UT8718 Operating Instructions Manual
...
PLEASE READ AND FOLLOW ALL WARNINGS
Read Operating Instructions
Always become familiar with all the
instructions and warnings before
operating any power tool.
Always Wear Approved
Eye Protection
Impact resistant eye protection
should meet or exceed the
standards as set forth in the United
States ANSI Z87.1, Occupational
and Educational Eye and Face
Protection. Look for the marking
Z87.1 on your eye protection to
insure that it is an approved style.
For further information, ANSI Z87.1,
Occupational and Educational Eye
and Face Protection, is available
from the American National
Standards Institute, Inc., 11 West
42nd Street, New York, NY 10036.
Hearing Protection is
Recommended
Hearing protection should be used
when the noise level exposure
equals or exceeds an 8 hour timeweighted average sound level of 85
dBA. Process noise, reflective
surfaces, other tools being
operated nearby, all add to the
noise level present in your work
area. If you are unable to determine
your noise level exposure, we
recommend the use of hearing
protection.
Avoid Prolonged Exposure to
Vibration
Tools can vibrate during use.
Prolonged exposure to vibration or
very repetitive hand and arm
movements, can cause injury.
Stop using any tool if discomfort,
tingling feeling or pain occurs. You
should consult your physician
before resuming use of the tool.
90 PSIG Maximum
This tool is designed to operate at
an air pressure of 90 pounds per
square inch gauge pressure (90
PSIG) maximum, at the tool. Use of
higher air pressure can, and may
cause injury. Also, the use of
higher air pressure places the
internal components under loads
and stresses they were not
designed for, causing premature
failure. The air supply should be
clean and dry, preferably
lubricated. For best results, drain
the moisture from your compressor
daily.
Universal Tool
A Division of Florida Pneumatic Manufacturing Corporation
851 Jupiter Park Lane, Jupiter, Florida 33458
Toll Free 1-800-327-9403
Read these instructions carefully before attempting to install, operate
or service this Florida Pneumatic product. Failure to comply with the
instructions could result in personal injury and/or property damage!
Retain these instructions for future reference.
devices as furnished by the manufacturer. Where an air tool is modified or
altered, the modifier shall provide the
safeguards to enable it to be safely used
in the operations intended and to comply
with any applicable provisions as
contained in ANSI B186.1.
Tool Installation
Pressure regulators shall be used to limit
air pressure to the rated pressure where
the supply pressure exceeds the tool’s
rated pressure. Air hoses and lines shall
be relieved of compressed air before
being disconnected or disjointed, unless
there is automatic valve closing protection at the joint being separated. Synthetic lubricants which can cause
deterioration of elastomer seals shall not
be used in air systems of air tools.
Tool Maintenance
It shall be the tool owner’s and/or
employer’s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools shall
be disconnected from their compressed
air supply before repairs are attempted.
Repairs shall be consistent with the
manufacturer’s recommended procedures. Tool, hoses and fittings shall be
replaced if unsuitable for safe operation.
It shall be the tool owner’s and/or
employer’s responsibility to keep required
rating markings and warnings on the tool
in legible condition.
FPMC
WARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals
known to cause cancer, birth defects or
reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement
and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals, work in a well-ventilated
area and work with approved safety
equipment such as those dust masks that
are specially designed to filter out
microscopic particles.
Safety Instructions
The following instructions are furnished
as general guidelines for use of your
pneumatic tool. They cannot comprehensively cover all possible or conceivable uses of the subject tool. For
additional information on the safe use
of air tools, we advise you to obtain a
copy of ANSI B186.1 Safety Code for
Portable Air Tools, available from the
following source:
American National Standards
Institute, Inc.
11 West 42nd Street
New York, NY 10036.
The use of the word “shall” in the
following instructions, indicates that
adherence to the particular requirement is necessary to conform to ANSI
B186.1.
Tool Application and Usage
Portable tools shall be used only for
the purposes intended in their design
and within the capacity for which they
were intended and rated. It shall be
the tool owner’s and/or employer’s
responsibility to instruct each operator
in the safe use of the tool. Tools shall
not be used without guards and safety
UT8893-26S & UT8893-60S
3/8-in. Straight Drill
Designed for continuous precision drilling for “Airframe Assembly” and “High
Volume Production” applications. Machined carbon fiber blades & carbon
steel motor parts allow “Oil Free” use; Highest precision engineering ensures
600,000 cycles of use ;Internal silencer baffle reduces noise pressure to 78
dBA; 0.9 HP motor ensures no slow down & clean break through.
Limited Warranty
Universal Tool warrants its tools to be free from defects in material and workmanship for one year from
the date of purchase. This warranty does not apply to tools which have been abused, misused,
modified or repaired by someone other than Universal Tool or its authorized service centers. If a
Universal Tool proves defective in material of workmanship within one year after purchase, return it to
any authorized service center or to Universal Tool, freight prepaid. Please enclose your name, address
and adequate proof of purchase date with a brief description of the defect. Universal Tool will, at its
option, repair or replace defective tools, free of charge. Repairs or replacements are warranted as
described above for the remainder of the warranty period. Universal Tool's sole liability and your
exclusive remedy under this warranty is limited to repair or replacemen
t of the defective tool. There are
no other warranties expressed or implied and Universal Tool shall not be liable for incidental, consequential or special damages, or any other damages, costs or expense of repair or replacement as described
above.
Specifications
UT8893-26S & UT8893-60S
3/8-in. Straight Drill
UT8893-26S UT8893-60S
Chuck Capacity 3/8" 3/8"
Free Speed (RPM) 2600 RPM 6000 RPM
Spindle Thread 3/8" x 24 TPI 3/8" x 24 TPI
Weight (lbs) 2.4 2.3
Length (in) 10-1/4" 10-1/4"
Average Air (CFM) 4.5 4.5
Rec Hose Size (in) 3/8" 3/8"
Inlet Size (NPT) 1/4" 1/4"
Max. Pressure 90 PSI 90 PSI
Loading...