Universal Scientific UNA900 User Manual
User Guide for UNA Module & Socket EVB
USI P/N 8500-002990-00
Department
MP
Date 2012/04/16
Version V1.1
The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
Content
1. FCC Regulations..................................................................................................1
2. RF Exposure Information..................................................................................2
3. Information of Installed Module.......................................................................3
4. Guide to Use .........................................................................................................4
1) Function of Socket EVB V21..........................................................................4
2) Configure the Socket EVB..............................................................................6
3) Insert the SIM card............................................................................................8
4) Place the Module...............................................................................................9
5) Connect the antenna......................................................................................10
6) Download setting.............................................................................................11
7) Manual control module model.....................................................................12
8) Rework list for PCM Codec...........................................................................13
The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
1. FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiated
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
2. RF Exposure Information
This Modular Approval is limited to OEM installation for mobile and fixed
applications only. The antenna installation and operating configurations of this
transmitter, including any applicable source-based time-averaging duty factor,
antenna gain and cable loss must satisfy MPE categorical Exclusion
Requirements of §2.1091.
The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons, must not be collocated
or operating in conjunction with any other antenna or transmitter, except in
accordance with FCC multi-transmitter product procedures.
The end user has no manual instructions to remove or install the device and a
separate approval is required for all other operating configurations, including
portable configurations with respect to 2.1093 and different antenna
configurations.
Maximum antenna gain allowed for use with this device is 2 dBi.
When the module is installed in the host device, the FCC ID label must be
visible through a window on the final device or it must be visible when an
access panel, door or cover is easily re-moved. If not, a second label must be
placed on the outside of the final device that contains the following text:
“Contains FCC ID: IXM-UNA900”.
The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
Frequency Stability covers operating
3. Information of Installed Module
Module Name
FCC ID
HW Version
SW Version
GSM Band
UMTS Band
GSM Feature
GPRS
EDGE
UMTS Feature
AT Command
UNA_900
IXM-UNA900
V2.1
MAUI.11A.W11.12.MP.V67.F1
GSM 850, E-GSM 900, DCS 1800, PCS 1900
FDD I, FDD VIII
Release 99
Release 6, Multi-slot class 12
Release 6, Multi-slot class 12
HSDPA, HSUPA (UMTS Release 6)
3GPP TS 27.007, 27.005
SIM/USIM
Interface
Operating Temperature
Operating Voltage
Support 3V and 1.8V
USB 2.0 high speed
temperature range of -20° to +50°C
3.5 ~ 4.2V
The information contained herein is the exclusive property of Universal Scientific Industrial Co., Ltd. and shall not be
distributed, reproduced, or disclosed in whole or in part without prior written permission of USI Co., Ltd.
Loading...