1 2
The RF30 Remote
WELCOME
The RF30 Remote
CONTNETS
LOCATION OF
CONTROLS
Keypad Layout 3
GETTING
STARTED
Overview 4
Battery Installation 4
Activating Component Commands 5
Light Button 6
BASIC SETUP
Overview 7
Pre-Programmed Code Method 7
Learning Method 15
Transmitting (Busy Signal) Icon. 19
Child Lock Feature 19
CUSTOMIZING
YOUR RF30
WITH SPECIAL
ADVANCED
FEATURES
Customizing the LCD Touch Screen 20
Favorite Channel Setup 23
MacroPower
TM
Setup 26
SimpleSound
TM
Setup &
Other ‘Punch Throughs’ 30
Setting Backlight Options 32
Hiding & Adding Pages 33
Recalling Pre-programmed
Setup Code Numbers 35
Cloning other RF30s 36
ERASING
COMMANDS
Overview 38
Erasing Learned Button,
Macro or Favorite
Channel Commands 38
Re-setting RF30 to Original
Factory Default Settings 40
THE OPTIONAL
POWERBLASTER
TM
PowerBlaster
TM
41
PREPROGRAMMED
CODE TABLES
Pre-Programmed Code Tables 44
NOTE 64
PREPROGRAMMED
CODE NOTES
Pre-Programmed Code Notes 43
OTHER
INFO
FAQ 65
Warranty 66
Specifications 66
simplify your home
entertainment experience.
The Quick Setup DVD
Program Guide supplied
with the RF30 will assist you
in programming your remote
by guiding you through an
easy step-by-step process.
This Owner’s Manual is
designed as a companion
reference source to the
DVD Guide, should you need
to refer back to a particular
section, or review certain
instruction detail not covered in the DVD. However,
if you are unable to watch
the DVD Guide for some
reason, everything you need
to know about programming
the RF30 is contained in this
Manual.
Congratulations on
purchasing Universal
Remote Control’s
MASTERCONTROLTMRF30
Pre-programmed and Learning
Remote Control! You now
have the power to control
your entire home
entertainment system with
one easy-to-use remote.
The RF30 can be used with
thousands of audio/video
Components because of the
extensive code library
pre-programmed into the
remote. And, the RF30’s
impressive lineup of special
advanced features can
automate and customize the
operation of your system in
many ways. So... get ready
to sit back, relax and
Congratulations!
MASTERCONTROL™ RF30 Owner’s Manual
© 2006 Universal Remote Control, Inc.
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: (914) 835-4484 Fax: (914) 835-4532
The information in this manual is copyright protected. No part of this manual
may be copied or reproduced in any form without prior written consent from
Universal Remote Control, Inc. UNIVERSAL REMOTE CONTROL, INC. SHALL
NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS /
OMISSIONS MADE IN THIS MANUAL. The information in this manual may be
subject to change without prior notice. MASTERCONTROL, PowerBlaster,
MacroPower, and SimpleSound are trademarks of Universal Remote Control,
Inc. All other brand or product names are trademarks or registered trademarks
of their respective companies or organizations.
TV 45
CABLE 48
DVD 50
VCR 52
AUDIO 54
SAT 57
CD 58
LDP 60
TAPE 61
AUX 62
3 4
Keypad Layout
LOCATION OF CONTROLS
Overview & Battery Installation
GETTING STARTED
Getting Started-Overview
This is what MASTERCONTROLTMRF30 is all about!
The RF30 is designed to operate up to 15 different
Audio/Video Components and is pre-programmed to
operate virtually all brands of TV, VCR, DVD and CD
Players, Cable Set Top Boxes, Satellite Receivers, TiVo
and other DVRs, Audio Components, Tape Decks,
Multimedia PCs, XM Radio, Ipod, X-Box, Lighting Controls
and other custom installation products. It also offers an
impressive lineup of special features designed to provide
you with many time-saving conveniences and enhance
your overall entertainment experience. However, we
strongly recommend that you fully complete all of the
Basic Setup steps before proceeding to customize your
RF30 with any of the special advanced features.
The very first step is to
insert the four AAA batteries that are included in the
package into the battery
compartment located in the
back of the remote. Just
press the tab and lift off the
cover. Please be sure to
insert the batteries correctly
as you see in the diagram.
Remember, there is a
positive and negative end
to each battery and you can
tell by the + (positive) and –
(negative) symbols. Once
the batteries are correctly
installed, replace the cover.
Now you’re ready to start!
Battery Installation
LIGHT
BUTTON
PAGE
BUTTONS
changes the page of
buttons displayed
PAGE
NUMBERS
SCREEN
BUTTONS
MAIN
BUTTON
takes you to the main menu
FUNCTION
BUTTONS
Touch the
Screen to use
the Screen
Buttons
65
Activating Component Commands
GETTING STARTED
LIGHT BUTTON
GETTING STARTED
Once you’ve programmed
RF30 for your Components,
all you have to do to operate a specific Component is
first, press the MAIN button.
This will display Page 1 of
the MAIN menu on the LCD
touch screen. Page 1 of the
MAIN menu displays seven
Components, plus FAV
(Favorite Channel). Then,
simply select the
Component you want to
operate by pressing the
desired Component display
button on the LCD Touch
Screen. As an example, if
you press the TV display
button, the display label at
the top of the screen will
change from MAIN to TV,
and all the buttons on RF30
will work your TV. To oper-ate
another Component,
simply press the MAIN
button again to return to
Page 1 of the MAIN menu
and select the next
Component you want to
operate.
If you don’t see the
Component you want to
control on Page 1 of the
MAIN menu, just use the
PAGE (
) ( ) display buttons
at the bottom of the screen
to bring up Page 2 of the
MAIN menu which displays
an additional eight
Components.
Each Component is provided
with four pages of prelabeled command display
buttons (or space for additional command display buttons). Once again, simply
use the PAGE (
) ( ) display
buttons to take you to the
next command page, or
return you to the previous
command page.
Activating Component Commands –
Simple, Easy, Intuitive
Light Button
The fully backlit keypad makes the RF30 easy to use in the
dark or dim lighting conditions. Simply press the LIGHT
button to backlight all the keypad buttons and LCD touch
screen. To turn off the backlight, press the LIGHT button
again, or just wait ten seconds (the backlight automatically
shuts itself off). Lights out!
Try it out!
TV DISPLAY
BUTTON
FAV
BUTTON
PAGE
BUTTONS
MAIN
BUTTON
LIGHT
BUTTON
7 8
Overview &
Pre-Programmed Code Method
BASIC SETUP
Pre-Programmed Code Method
BASIC SETUP
STEP 1:
The pre-programmed 3-digit
codes are found in the back of
this Manual on page 44. The
codes are listed by Component
category (i.e., TV, VCR, DVD,
etc.), then by brand name. For
instance, if you want to locate
a code for a Sony TV, first
locate the TV category, and
then look for the Sony brand.
Once you have located the
3-digit code (or in some cases,
several code numbers) for the
Component that you want to
operate with your RF30, write
them ALL down on a piece of
note paper. It’s important that
you write down all the codes
because only one code is going
to work for you.
STEP 2:
Now, turn on the Component
you want to program... let’s say
your TV to start. Look up your
TV’s manufacturer setup code
from your reference list.
STEP 3:
Press and hold the MAIN and ENT
(Enter) buttons at the same time
for approximately 3 seconds, until
the word “SETUP” is displayed at
the top of the LCD touch screen.
This signals that you are now in
setup mode.
Pre-Programmed Code Method
Basic Setup - Overview
There are two ways to program the RF30:
• The Pre-Programmed Code Method
• The Learning Method
The Pre-Programmed Code Method allows you to set up
all the buttons at once, so it’s the fastest and easiest of
the two methods. The Learning Method allows you to
transfer functions from other remotes (old or new), one
button at a time.
IMPORTANT:
You now have 30 seconds to perform
the next step while you are in SETUP
mode. If you don’t press a button
within 30 seconds, SETUP will disappear from the screen, signaling that
you have exited setup mode and you
will need to start over.
MAIN
BUTTON
ENTER
BUTTON
9 10
Pre-Programmed Code Method
BASIC SETUP
Pre-Programmed Code Method
BASIC SETUP
STEP 4:
Press the P-PRO button to select
the Pre-Programmed Method.
The screen will then display the
seven Components (and FAV) on
Page 1 of the MAIN menu.
To display Page 2 of the MAIN
menu that lists an additional
eight Components, simply press
the ( or ) Page buttons at the
bottom of the screen.
STEP 5:
Press the Component button
you want to program. For
example: If you want to setup
the TV Component button,
press the TV Component button. The display at the bottom
of the LCD screen will flash
“FROM - TABLE”.
STEP 6:
In this step you verify the type
of component you plan to
operate with this component
button. For example: If you plan
to operate the TV component
with the TV button, simply press
the TV button once again.
However, if for example you are
setting up AUX to operate a
second DVD Player, you would
first need to press AUX in Step
5, and then DVD in Step 6.
DEVICES
FAV
BUTTON
P-PRO
BUTTON
12
Pre-Programmed Code Method
BASIC SETUP
11
Pre-Programmed Code Method
BASIC SETUP
STEP 7:
Point the RF30 toward the
Component you want to
program, (in this example, TV),
and punch in the 3-digit code
that you wrote down for that
specific Component. Use the
Number buttons 0-9 on the
remote to punch in the code.
If the 3-digit code number that
you just punched in is correct,
the Component will turn off. If
the Component does not turn
off, continue entering code
numbers from your list until the
Component turns off. Some
brands have several possible
code numbers.
STEP 8:
When the Component turns off,
press the ON button to turn the
Component back on. Now you
can test the Volume and
Channel buttons (for TV), or
PLAY and STOP (for VCR and
DVD) to make sure they all
work. If any of the buttons do
not work properly, you need to
find a new correct code. For
example, maybe your Sony TV
turned off with code number 147,
but the volume controls did not
work properly. If this is the case,
try the next code number listed
for that Component until you find
a perfect match.
ON
BUTTON
VOLUME
BUTTONS
CHANNEL
BUTTONS
PLAY
BUTTON
STOP
BUTTON
UP & DOWN
BUTTONS
NUMBER
BUTTONS
NOTE:
If the Component fails to turn off after you have entered
all the code numbers listed for your brand, you can scan
through all the other code numbers that are pre-loaded
into the RF30 for that Component (in this case TV) by
using the UP or DOWN buttons on the screen. (There is
a chance that your Component was actually manufactured
by another brand.) However, most of the code tables are
so large that it is usually faster to use the Learning Method
on Page 15.
13 14
Pre-Programmed Code Method
BASIC SETUP
Pre-Programmed Code Method
BASIC SETUP
STEP 9:
Once you have found the right
code, save the code number by
pressing the SAVE button that
appears on the LCD screen.
The LCD screen will blink
“SAVED” two times, signaling
that the code number has been
successfully saved.
STEP 10:
Exit SETUP mode by pressing
the MAIN button two times.
When the LCD screen displays
MAIN, you are back in normal
operating mode.
SAVE
BUTTON
MAIN
BUTTON
NOW, PROGRAM THE REST OF YOUR
COMPONENTS BY REPEATING STEPS
1 THROUGH 9. IN MOST SYSTEMS,
YOU CAN FINISH BASIC SETUP IN
JUST A FEW MINUTES AND PUT ALL
YOUR OLD REMOTES AWAY.
IF YOU ARE STILL MISSING COMMANDS TO CONTROL ANY OF YOUR
COMPONENTS, USE THE LEARNING
METHOD ON PAGE 15.
15 16
Learning Method
BASIC SETUP
Learning Method
BASIC SETUP
MAIN
BUTTON
ENTER
BUTTON
LEARN
BUTTON
STEP 1:
Line-up the RF30 with the other
remote control, head-to-head,
one or two inches apart.
STEP 2:
On the RF30, press and hold the
MAIN and ENT (Enter) buttons
at the same time for approximately three seconds, until the
word “SETUP” is displayed at
the top of the LCD touch screen.
This signals you are now in
SETUP mode.
STEP 3:
Press the LEARN button on the
LCD screen. The top of the
screen will change to “LEARN”
and display the seven
Components (and FAV) from
Page 1 of the MAIN menu.
To display Page 2 of the MAIN
menu that lists an additional
eight Components, simply press
the ( or ) Page buttons at the
bottom of the screen.
STEP 4:
Select the Component you want
to teach commands to by
pressing that Component button
on the LCD screen (in this
example, TV). The top of the
screen will change to “TV”.
IMPORTANT:
You now have 30 seconds to perform
the next step while you are in SETUP
mode. If you don’t press a button
within 30 seconds, SETUP will disappear from the screen, signaling that
you have exited setup mode and you
will need to start over.
NOTE: If you want to teach any command to a Component button, press the
Component button once the top of the
screen displays “MAIN”, by pressing the
PAGE button. The top of the screen will
change to "READY". Then go to STEP 6.
The RF30 can actually ‘learn’ commands from other remote
controls (old or new), one-button-at-a-time, so it will never
become obsolete. RF30 is the last remote you’ll ever need!
Just follow these simple steps:
Learning Method
17 18
Learning Method
BASIC SETUP
Learning Method
BASIC SETUP
STEP 5:
Press any button on the RF30
that you want to teach a
command to. The top of the
screen will change to "READY"
and the bottom of the screen will
display the button you pressed.
STEP 6:
Press and hold the button on the
other remote control that you
want to ‘teach’ to the RF30 until
the LCD display on the RF30
changes to either “GOOD” or
“FAILD”. If the “GOOD” label
appears on top of the display
and “SAVED” flashes on the bottom, you were successful. If
the “FAILD” label appears on
top of the display, try ‘teaching’
the same button to the RF30
once again by repeating STEPS
5 and 6.
STEP 7:
Now, continue to teach the RF30
any other commands from your
old remotes by repeating STEPS
4 through 6 (to go back to STEP
4, simply press MAIN once).
STEP 8:
Once you have completed
teaching all the button
commands to the RF30, return to
normal operation by pressing the
MAIN button twice.
Test all your new commands. If
any of them don’t work, try the
Learning Method again, following these suggestions:
• Move to another room. Plasma
TVs, sunlight, halogen or quartz
lighting can interfere with the
learning process.
• Even though the old remote
seems to be working fine, put in
fresh alkaline batteries.
• Gradually vary the distance
between the remote controls.
Try 1”, 2” and so on, up to
4 feet.
• Try tapping the button on your
old remote instead of pressing
and holding it during the
learning process.
Some additional Information
regarding the Learning Process:
• Learned functions override any
existing pre-programmed
functions on the remote control.
• All buttons can be learned
except for the PAGE, MAIN and
LIGHT buttons.
• Learned functions are
automatically erased when a
new function is learned on the
same button.
• Learned functions are retained
even after a different Setup
Code Number is programmed
into the remote.
• To return to an original preprogrammed function, a learned
function must be erased.
NOTE: If you don’t see the display button
you would like to teach on the LCD
screen, use the (
or ) PAGE buttons at
the bottom of the screen.The only
buttons you can’t teach are the PAGE and
MAIN buttons.
19 20
Transmitting (Busy Signal) Icon
CUSTOMIZING
Customizing the LCD Touch Screen
CUSTOMIZING
STEP 1:
Press and hold the MAIN and
ENT (Enter) buttons at the same
time for approximately 3 seconds,
until the word “SETUP” is
displayed at the top of the LCD
touch screen. This signals that
you are now in setup mode.
STEP 3:
Press the TEXT button. The
screen will display the list of
Components and “EDIT” will
appear at the top of the screen.
STEP 4:
Navigate to the Component and
page where there is a button
label you want to EDIT, selecting
between the FAV, MAIN,
COMPONENT; then using the
PAGE button.
STEP 2:
Press the EDIT button. The LCD
display will change to the EDIT
menu.
IMPORTANT:You now have 30 seconds to
perform the next step while you are in
SETUP mode. If you don’t press a button
within 30 seconds, SETUP will disappear
from the screen, signaling that you have
exited setup mode and you will need to
start over.
NOTE: If you wish to change the name of
a Component button, press the Page (
)
button twice.The top of the display will
change to MAIN, and you can navigate to
MAIN page 1 or page 2 before going on
to Step 5.
When a command is being transmitted, an icon will appear
in the upper right corner of the LCD screen. This indicates
that a signal is being sent. This is particularly useful when
setting up Macros and FAVs, since it flashes with every step
of a sequence of commands.
Transmitting (Busy Signal) Icon
After you’ve finished all your basic setup, you can choose
to make operation easier by customizing the RF30 just the
way you want, using the Special Advanced Setup Features
described in this section.
Customizing Your RF30 with Special
Advanced Features
You can easily edit or change the name of any of the
display buttons (including Favorite Channels) on the LCD
screen by following these steps:
Customizing the LCD Touch Screen
CHILD LOCK FEATURE
This ‘child-lock’ feature prevents the unauthorized use of
the remote control by children. It blocks all operations of
the remote control.
To Activate:
Press the +10 and ENT (Enter) buttons simultaneously for
3 seconds. The bottom of the LCD will blink “LOCKED” three
times and then display “LOCKED”.
To Return to Normal Operation:
Press the +10 and ENT (Enter) buttons simultaneously again
for 3 seconds. The LCD will display the last use mode.
21 22
Customizing the LCD Touch Screen
CUSTOMIZING
Customizing the LCD Touch Screen
CUSTOMIZING
STEP 5:
Press the button you wish to
edit. The first character space
of your button label will start to
blink.
STEP 6:
Change the character by using
any of the number keys. Each
press of the same number button selects the next character of
that number’s group, as shown
in the diagram below.
STEP 7:
Once the character you want
appears, move to the next space
by pressing the Right cursor button.
STEP 8:
When you are finished editing
the button, press the button you
edited and “SAVED” will flash at
the bottom of the display.
To change any other button
labels on the same Component,
press the next button, then
repeat steps 6-8. If you wish to
edit a button on another
Component, press the MAIN button once, then repeat Steps 4-8.
STEP 9:
Once you’ve finished editing buttons, press the MAIN button four
times to return to normal operation.
UP CURSOR
Button deletes all text
LEFT CURSOR
Moves blinking
character left
DOWN CURSOR
deletes the currently
blinking character
RIGHT CURSOR
Moves blinking
character right
BLINKING
CHARACTER
23 24
Favorite Channel Setup
CUSTOMIZING
Favorite Channel Setup
CUSTOMIZING
This is one of RF30’s most desirable features. Once it’s set up,
you can select up to 40 favorite channels with the press of a
button - without the need to remember or type in a channel
number. Let the channel surfing begin!
To access Favorite Channel listings, press the MAIN button
to bring up Page 1 of the MAIN menu. Then press the FAV
(Favorite Channel) button on the LCD touch screen. The
screen changes to a list of favorite TV channels. Each button
can be set to instantly select the channel on your TV. There
are five pages of eight favorite channel buttons for a total of
40. Simply touch the PAGE buttons to display the other pages
of favorite channels.
To setup a Favorite Channel button, follow these steps:
Favorite Channel Setup
PAUSE
BUTTON
DEVICE
BUTTONS
STEP 1:
Press and hold the MAIN and
ENT (Enter) buttons at the same
time for approximately 3
seconds, until the word “SETUP”
is displayed at the top of the LCD
touch screen. This signals that
you are now in setup mode.
STEP 2:
Press the FAV display button.
The top of the display will show
“FAV”. The bottom of the display
will flash “SELECT”
STEP 3:
Use the Page buttons until you
locate the name (i.e., ABC, CBS,
NBC) of the favorite channel you
want to setup.
STEP 4:
Press the favorite channel
button you want to setup. The
top of the screen will change to
show the channel name. The
bottom of the screen displays
“STEP0”, indicating that you
have not entered the channel
number yet.
STEP 5:
Press either the TV, SAT or
CABLE Component button (select
the Component you use to enter
channel numbers).
STEP 6:
Press each of the number
buttons for the channel.
IMPORTANT:You now have 30 seconds to
perform the next step while you are in
SETUP mode. If you don’t press a button
within 30 seconds, SETUP will disappear
from the screen, signaling that you have
exited setup mode and you will need to
start over.
Note: If a number is repeated when setting the channel (for example, channel
“33” or “522’), it is usually best to set a
half second delay in between the identical numbers by pressing the (II) PAUSE
button. Each press of the PAUSE button
increases the delay by a half second.
NOTE: Some brands of television require
an ENT (Enter) command after the channel numbers.
FAV
BUTTON
25 26
Favorite Channel Setup
CUSTOMIZING
MacroPower Setup
CUSTOMIZING
SAVE
BUTTON
MacroPowerTMSetup
MacroPowerTMis a unique feature that enables you to turn
all of your Components ON or OFF, at the same time, simply
with the press of one button. We call that a “Macro”.
What would normally take multiple remotes and button
pushes, the RF30 can accomplish with the press of one
button. In addition to the Power ON or OFF buttons, any of
the Display buttons (on any Component or Page) can be set
to be Macro buttons as well. Feel the power!
To setup a Power ON macro button that will turn ON several
components at the same time (for example, TV, VCR and
CABLE), follow these easy steps:
STEP 7:
Press the LIGHT button after you
enter the channel number. A
new screen appears displaying
SAVE, UNDO or EXIT.
STEP 8:
To save the channel you
entered, press the SAVE button.
The UNDO button lets you erase
the last entry. The EXIT button
erases all entries for this button.
STEP 9:
When you are finished setting
up Favorite Channel buttons,
press the MAIN button twice to
return to normal operation.
STEP 1:
Press and hold the MAIN and
ENT (Enter) buttons at the same
time for approximately 3
seconds, until the word “SETUP”
is displayed at the top of the LCD
touch screen. This signals that
you are now in setup mode.
STEP 2:
Press the MACRO button on the
LCD screen. The top of the
screen will display “MACRO”.
The bottom of the display will
flash “SELECT”.
STEP 3:
Press the ON button. “ON” will
display at the top of the LCD
screen. “STEP0” will display at
the bottom of the screen
indicating that no macro steps
have been entered yet.
STEP 4:
Press the first component
button you want the Macro to
turn on (in this example, TV)
and “TV” will display at the top
of the screen and “STEP 1” at
the bottom.
STEP 5:
Then, press the ON button to
confirm the command and
“STEP 2” will display at the
bottom of the screen. (NOTE:
Whenever a button is pressed,
another Macro step is counted
and displayed at the bottom of
the screen.)
STEP 6:
Now, press the MAIN button to
return to the Main Component
listing. (“STEP 3” will display at
the bottom of the screen.)
IMPORTANT:You now have 30 seconds to
perform the next step while you are in
SETUP mode. If you don’t press a button
within 30 seconds, SETUP will disappear
from the screen, signaling that you have
exited setup mode and you will need to
start over.
27 28
MacroPower Setup
CUSTOMIZING
MacroPower Setup
CUSTOMIZING
STEP 7:
Press the second component
that you want the Macro to turn
on (in this example, VCR) and
“VCR” will display at the top of
the screen. (“STEP 4” will
display at the bottom of the
screen.)
STEP 8:
Then, press the ON button to
confirm the command. (“STEP
5” will display at the bottom of
the screen.)
STEP 9:
Now, press the MAIN button to
return to the Main Component
listing. (“STEP 6” will display at
the bottom of the screen.)
STEP 10:
Press the third component that
you want the Macro to turn on
(in this example, CABLE) and
“CABLE” will display at the top
of the screen. (“STEP 7” will
display at the bottom of the
screen.)
STEP 11:
Then, press the ON button to
confirm the command. (“STEP
8” will display at the bottom of
the screen.)
You can also program delays in
between commands by pressing
the (II) PAUSE button. Each
press adds half a second to the
delay.
STEP 12:
Press the LIGHT button to end
your macro. A new screen will
appear:
STEP 13:
If you are satisfied with your
macro, press SAVE. The UNDO
button lets you erase the last
step. The EXIT button erases all
the macro steps.
STEP 14:
Press the MAIN button twice to
return to normal operation.
SAVE
BUTTON
UNDO
BUTTON
EXIT
BUTTON
NOTE: Don’t worry about the number of
steps. Each macro button can store up to
190 steps, so you are not likely to run out
of steps!
29 30
MacroPower Setup
CUSTOMIZING
SimpleSound Setup &
Other ‘Punch Throughs’
CUSTOMIZING
Advanced Macro Options:
SETTING UP A POWER OFF MACRO:
Simply follow the same steps as outlined above, except
press the OFF button in place of the ON button.
SETTING A COMPONENT BUTTON AS MACRO:
If you wish to set one of the Component buttons as a
macro, in STEP 3, press the Page ( button twice. The top
of the display will change to MAIN, and you can navigate
to MAIN page 1 or page 2. Press the Component button
you want to set as a Macro button. The top of the screen
will display the button label you selected. Select the
Component and Page that has a button you want in your
Macro using the MAIN, Component and Page buttons.
Simply press the button(s) with the command(s) you want
in your Macro. Then complete and save the Macro by
following STEPs 12 and 13 as outlined above.
PROGRAMMING A “RESS & HOLD” MACRO:
Another option for Component button macros is to only
send the macro if the button is pressed and held. This is
setup by entering a delay as the first step of the macro.
The amount of delay determines how long the user must
press the button before the macro is sent. The advantage
of this option is that a normal press of the COMPONENT
button will simply switch Components without sending
the macro command.
SimpleSoundTMSetup & Other ‘Punch Throughs’
SimpleSoundTMis a dynamic feature that gives you total
volume control over all the Components in your system,
even those without their own built-in volume control, such
as TiVo, DVD and VCR... saving you the hassle and
inconvenience of constantly needing to switch between
Component modes on the remote. With SimpleSound
TM
,
you can set the RF30’s volume control buttons to always
control the sound in your system, even when you’re in
VCR or DVD mode, without switching back to AUDIO or TV.
Even more exciting, SimpleSound
TM
is what is called a
‘Punch Through’ feature and is not limited strictly to volume
control. Click and enjoy!
PUNCH
VOLUME
BUTTON
STEP 1:
In a basic home entertainment
system, the sound may come
from your TV. In a more
advanced system, the sound
may come from your audio
Component such as a Surround
Sound Receiver or Home
Theatre system. So, first, you
need to identify which
Component you want to use in
your system for sound.
STEP 2:
Press and hold the MAIN and
ENT (Enter) buttons at the same
time for approximately 3 seconds,
until the word “SETUP” is
displayed at the top of the LCD
touch screen. This signals that
you are now in setup mode.
STEP 3:
From the LCD screen Setup
menu, press the PUNCH button.
STEP 4:
Then press the VOL (Volume)
button. The screen will display
“VOL” at the top. This sets up
the group of three buttons
(Volume Up, Volume Down and
Mute) in one action!
IMPORTANT: You now have 30
seconds to perform the next step
while you are in SETUP mode.
If you don’s press a button within
30 seconds, SETUP will disappear from the screen, signaling
that you have exited setup mode
and you will need to start over.
31 32
SimpleSound Setup &
Other ‘Punch Throughs’
CUSTOMIZING
Setting Backlight Options
CUSTOMIZING
MAIN
BUTTON
UP & DOWN
CURSOR
HIGH
CONTRAST
LOW
CONTRAST
The bottom of the display flashes
“PUNCH TO”. Press the button
for the Component that doesn’t
have volume control commands
yet (i.e.,DVD). This is the
Component you are going to
PUNCH TO for the volume and
mute commands.
NOTE: If you want to PUNCH TO the MAIN
Component, press the POWER OFF button
at this time.
STEP 5:
The bottom of the display will
then flash “PUNCH FROM”. Now
select the Component that has
the volume commands you want
to use (i.e.,TV for systems using
the TV speakers, AUDIO for
systems with surround sound
receivers). The bottom of the
display will flash “SAVED”.
STEP 6:
Repeat STEPS 4-5 until all your
Components operate the volume
perfectly.
STEP 7:
Press the MAIN button twice to
return to normal operating mode
and test your SimpleSound
TM
settings.
Simply perform the steps outlined
above, but in STEP 4, press one
of the control options (CH, PLAY or
VOD).
NOTE:The Punch Through feature is not
limited to volume and can also be applied
to channel selection or other functions. If
you find yourself switching to a particular
Component frequently to use a group of
controls, consider using Punch Through for
another group, as listed here:
VOL - Volume Up,Volume Down and
Mute
CH - Channel Up, Channel Down,
Previous Ch and Channel (0-9)
buttons.
PLAY - Play, Stop, Pause, Rewind and
Fast Forward
VOD - Guide, Menu, Info, Exit, Up,
Down, Left, Right, Select
Setting Backlight Options
You can customize the backlighting feature to suit your
specific preferences by following these simple steps:
Adjusting Length of Backlight Time
You can adjust the amount of time that the RF30 backlight
stays on by entering the SETUP mode and proceeding to
page two (using the PAGE (
button), then pressing the
LIGHT button on the display (not the Backlight button).
Then enter the amount of time you would like the light to
stay on using the number pad (0-99 seconds). After making
your selection, press the SAVE button.
Adjusting Contrast
You can make the text darker by pressing both the MAIN
and cursor UP buttons at the same time. To make the text
appear lighter, press both the MAIN and cursor DOWN
buttons at the same time.
Turning OFF Backlighting
If you don’t want backlighting at all (this extends battery
life), press the ON button that appears on the screen. The
ON will change to OFF. Press the SAVE button. Exit the
setup mode by pressing the MAIN button.
33 34
Hiding & Adding Pages
Pages CUSTOMIZING
Hiding & Adding Pages
CUSTOMIZING
Hiding and Adding Pages
Each of your RF30 Components actually contains five
pages. However, only four pages are visible in the factory
default setting. One page is hidden in each Component.
If you wish to use the hidden page, you can ADD it. If you
don’t want to use some of the existing pages, you can HIDE
them. You can add or hide pages on Components OR on
your favorite channel pages using this simple process:
NOTE: Be sure to program your Macros before you hide pages with
potential macros in them. You can’t access hidden pages during
macro setup. However, after you finish Macro setup, you can hide
pages without affecting operation of your macros.
STEP 1:
Press and hold the MAIN and
ENT (Enter) buttons at the same
time for approximately 3 seconds, until the word ”SETUP” is
displayed at the top of the LCD
touch screen. This signals that
you are now in setup mode.
STEP 2:
Press the EDIT button on the
LCD screen.
STEP 3:
Press the PAGE button once the
screen changes to EDIT mode.
STEP 4:
“PAGE” appears at the top of the
screen. Now, you can navigate to
any page, using the MAIN,
COMPONENT, FAV, and PAGE
buttons.
STEP 5:
When you select a page, the top
of the screen indicates whether
you want to “ADD?” or “HIDE”
the page displayed. When you
want to change a page’s visibility
(i.e., either ADD or HIDE),
simply press the LIGHT button.
STEP 6:
You can continue to ADD or
HIDE pages on other devices
by repeating Steps 4 and 5.
STEP 7:
When you are finished adding
and hiding pages, press the
MAIN button four times to return
to normal operation.
IMPORTANT:You now have 30 seconds
to perform the next step while you are
in SETUP mode. If you don’t press a
button within 30 seconds, SETUP will
disappear from the screen, signaling
that you have exited setup mode and
you will need to start over.
EDIT
BUTTON
PAGE
BUTTON
PAGE
BUTTONS
COMPONENT
BUTTON
FAV
BUTTON
MAIN
BUTTON
This page is hidden.To ADD
it, press the LIGHT button
This page is visible.To HIDE
it, press the LIGHT button.
35 36
Recalling Pre-Programmed
Setup Code Numbers
CUSTOMIZING
Cloning Other RF30s
CUSTOMIZING
Recalling Pre-Programmed Setup Code
Numbers
In case you didn’t write down the Pre-Programmed Code
Numbers that you used to set up your RF30, you can easily
recall them using this simple process:.
Cloning Other RF30s
If you are fortunate enough to own more than one RF30,
you’ll be happy to know that you can easily copy and
transfer all the setup from one RF30 to another. Just follow
these easy steps:
STEP 1:
Press and hold the MAIN and
ENT (Enter) buttons at the same
time for approximately 3 seconds,
until the word “SETUP” is
displayed at the top of the LCD
touch screen. This signals that
you are now in setup mode.
STEP 2:
Press the RECAL button on the
LCD screen. Each of the four
screen pages will display the
Component name and its
corresponding code number.
STEP 3:
Write down the code numbers
as they appear for future
reference. Page 43 of this
manual provides a convenient
space for you to record your
code numbers.
STEP 4:
Return to normal operation by
pressing the MAIN button twice.
IMPORTANT:You now have 30 seconds to
perform the next step while you are in
SETUP mode. If you don’t press a button
within 30 seconds, SETUP will disappear
from the screen, signaling that you have
exited setup mode and you will need to
start over.
STEP 1:
For both the programmed RF30
that you want to clone, and
unprogrammed RF30, press and
hold the MAIN and ENT (Enter)
buttons at the same time for
approximately 3 seconds, until
the word “SETUP” is displayed
at the top of their respective LCD
touch screens. This signals that
both remotes are now in setup
mode.
STEP 2:
Press a PAGE button on each
remote to bring up Page 2 of
Setup and display the CLONE
button.
STEP 3:
Press the CLONE button on each
remote.
IMPORTANT:You now have 30 seconds to
perform the next step while you are in
SETUP mode. If you don’t press a button
within 30 seconds, SETUP will disappear
from the screen, signaling that you have
exited setup mode and you will need to
start over.
NOTE: Use the ( or ) page buttons to
display any of the four pages of
Components and their code numbers.
37 38
Cloning Other RF30s
CUSTOMIZING
Erasing Learned Buttons, Macros or
Favorite Channels
ERASING COMMANDS
Erasing Commands - Overview
You can erase an individual button with a learned
command, a macro or a favorite channel. You can erase an
ENTIRE Component’s learned command or macro buttons.
You can also erase ALL your learned commands on all
Components or all your macros or favorite channels
everywhere.
If you really want a fresh start, it is possible to reset
everything to the factory default settings.
Erasing Learned Buttons, Macros or Favorite Channels
STEP 4:
Align the two RF30s head-tohead,
about an inch apart.
STEP 5:
Press the RECV display button
on the unprogrammed RF30 that
you want to setup by cloning.
STEP 6:
Press the SEND display button
on the programmed RF30 that
you want to clone.
STEP 7:
Press the START button on the
unprogrammed RF30, and then
press the START button on the
programmed RF30 that you want
to clone.
STEP 8:
Return to normal operation by
pressing the MAIN button twice.
NOTE: Cloning typically takes about 40
seconds. After successful cloning is completed, the newly cloned RF30 will flash
“GOOD”.
STEP 2:
Press the ERASE button on the
LCD screen.
STEP 3:
Press either the LEARN, MACRO
or FAV button. The following
screen appears:
ALL - Erases ALL of the specified
(Learned, Macro or FAV buttons
everywhere in the RF30)
DEVICE - Erases all learned or
Macro buttons in a single
Component (NOTE: This option
is not available for FAVs.)
KEY - Erases one button only.
STEP 1:
Press and hold the MAIN and
ENT (Enter) buttons at the same
time for approximately 3 seconds,
until the word “SETUP” is
displayed at the top of the LCD
touch screen. This signals that
you are now in setup mode.
IMPORTANT:You now have 30 seconds to
perform the next step while you are in
SETUP mode. If you don’t press a button
within 30 seconds, SETUP will disappear
from the screen, signaling that you have
exited setup mode and you will need to
start over.
39 40
Erasing Learned Buttons, Macros or
Favorite Channels
ERASING COMMANDS
Re-setting RF30 to Original
Factory Default Settings
ERASING COMMANDS
STEP 4:
If you press ALL, the RF30
displays a “SURE?” button.
After the SURE button is pressed,
all the buttons will be erased.
If you press DEVICE, a list of
Components will appear. Press
the Component button that you
wish to erase. The bottom of the
screen will flash ERASE twice,
then ERASED.
If you press KEY, you’ll have to
navigate to the Component and
Page you want using the MAIN,
COMPONENT and PAGE buttons.
Press a button to erase it. The
bottom of the display will flash
ERASE twice, then ERASED.
STEP 5:
To return to normal operating
mode, press the MAIN button
four times
STEP 1:
press and hold both the MAIN
and the STOP buttons for 10
seconds.
STEP 2:
After 10 seconds, the RESET
screen appears. Press the ALL
button. The RF30 will display a
“SURE?” button. Press the
SURE button to erase all of your
settings and return to the factory
default setup.
MAIN
BUTTON
STOP
BUTTON
SURE
BUTTON
SURE
BUTTON
Re-setting RF30 to Original
Factory Default Settings
If you want to start with a clean slate, you can re-set the
RF30 its original factory default settings by performing the
following steps.
NOTE: This process will essentially erase EVERYTHING you
have programmed into the RF30.
41 42
‘Barroer -Free’ RF control
THE POWER BLASTER
‘Barroer -Free’ RF control
THE POWER BLASTER
The Optional PowerBlaster
TM
(for ‘barrier-free’ RF control)
[Sold separately]
Of all the fabulous RF30 features, this is probably the most
exciting. When used in combination with the optional
PowerBlaster
TM
, the RF30 becomes an amazing remote
control powerhouse that sends multi-directional RF (Radio
Frequency) signals that pass through walls, doors and
floors - both indoors and outdoors.
This changes everything! It enables you to control
Components that are completely out-of-sight, up to 100’
away. The PowerBlaster
TM
picks up RF30’s radio frequency
signals from any direction, regardless of distance, so RF30
doesn’t need to be pointed directly at any Component.
Just imagine - no more pointing! Now you can close your
entertainment center doors, hide your Components, and
still control them with ease. Control outdoor speakers on
your patio. Control your Components anywhere!
One of the best things about this is - nothing has to be
done to the RF30 for this feature to work. Every time you
press a button on the RF30, it sends both a standard IR
(Infrared Command) AND an RF (Radio Frequency) signal.
If you install the PowerBlaster
TM
kit, it will automatically
receive RF30’s radio signals and translate them into the
infrared commands that control your Components.
The RF30 sends radio signal to the PowerBlaster
TM
, which
is a radio receiver.
The PowerBlaster
TM
converts radio signals to standard
infrared commands and sends them out via a built-in front
blaster to Components in the same cabinet space.
Self-adhesive “flashers” (included in the PowerBlaster
TM
kit)
affix to the front panels of your Components. The flashers
relay infrared commands to Components out-of-sight of the
PowerBlaster’s front blaster. The flashers plug into
PowerBlaster’s rear flasher line output jacks. Each flasher
has a 10’ cable to easily reach Components on nearby
shelves.
NOTE: The RF30's radio signals will not control Components
directly. You must have a PowerBlaster
TM
to receive the
RF30's radio signals. Components that came with “no
pointing” radio remote controls cannot be operated by the
RF30 unless the Component can be switched to standard IR
(Infrared Control) via its internal menus. Some remote
control ceiling fans are radio only and cannot be operated
by the RF30.
43 44
Pre-Programmed Code Notes
PRE-PROGRAMMED CODE NOTES
Pre-Programmed Code Tables
PRE-PROGRAMMED CODE TABLES
Pre-Programmed Code Notes
Record the three digit codes for your system here:
Pre-Programmed Code Tables
The RF30’s Pre-Programmed code library is divided into
categories (TV, VCR, AUX, etc.). Each category actually
includes many types of Components. For example, the VCR
category includes TV/VCR combo units.
Within each category, the code numbers are listed in rows by
brand (Sony, Panasonic, B & K, etc.). Some brands have more
than one three digit code for you to try. Just circle the correct
row and refer to it while you setup (step by step instructions
for using Pre-Programmed codes are found on page 7).
TV TVs, Plasmas, Projectors and Monitors
CABLE Cable TVs and Web TVs
DVD DVD Players and TV/DVD Combos
VCR VCRs and TV/VCR Combos
AUDIO Amps, Preamps, A/V Receivers and XM Radios
SAT Satellite Receivers
CD CD Players and CD Changers
DVR TiVo, Replay and other DVR’s
LDP Laser Disc Players
LIGHT Lighting System and Dimmers
TAPE Tape Decks
AUX Multimedia PCs, Xbox, iPod Controls
and Custom Installation Products
PHONO Phonographs
AUDIO
DVD
CD
SAT
TV
VCR
CABLE
AUX
LIGHT
TAPE
PHONO
TV2
VCR2
DVR
LDP
XM RADIO
IPOD
X-BOX
46
CODE TABLES
TV
BRAND CODE NUMBERS
45
BRAND CODE NUMBERS
TV
CODE TABLES
ADMIRAL 072 081 161 160
ADVENT 247
AKAI 197 146 248
A MARK 112 143
AMPRO 167 073 157 183
AMSTRAD 052
ANAM 043 054 056 080 112 131
AOC 197 004 112 058
APEX DIGITAL 006 310
AUDIOVOX 076 273
BARCO 233
BLAUPUNKT 088
BROKSONIC 238
CAIRN 201
CANDLE 197 002 003 004
CAPEHART 058
CETRONIC 043
CITIZEN 197 002 003 004 043 101 103 143
CLASSIC 043
CONCERTO 004
CONTEC 043 050 051
CORONADO 143
CRAIG 043 054
CROWN 043 143
CURTIS MATHES 197 101 004 143
CXC 043
DAEWOO 004 016 043 044 076 103 114 125 127 143
DAYTRON 004 143
DELL 319 320 321
DREAMVISION 235 345
DWIN 177 257
DYNASTY 043
DYNATECH 062
EIKI 187
ELECTROHOME 143 024 076 196
EMERSON 028 048 043 155 005 197 004 047 050 051 076 096 143 151
153 154
FISHER 007 057
EPSON 324
ESA 323
FUJITSU 198 246 346
FUNAI 028 043
FUTURETECH 043
GATEWAY 242 268
GE 160 144 165 073 197 008 009 034 056 074 130 155 161 004
091 157 183
GOLDSTAR 113 116 102 004 106 112 119 127 143
HALL MARK 004
HANNSPREE 381
HITACHI 011 163 166 004 009 010 012 023 075 143 158 072
HP 316 327 378
HYUNDAI 337 338
INFINITY 164
INFOCUS 230 330 333
INSIGNIA 350
JBL 164
JCPENNEY 004 024 197 008 009 030 065 101 143 156 160
JENSEN 013
JVC 038 034 070 083 145 199 210 240 241
KEC 043
KENWOOD 197 070
KLOSS 002 059
KMC 143
KTV 043 197 143 154
LG 113 116 102 004 106 112 119 127 143 243 284 363 365
LODGENET 072
LOEWE 164
LOGIK 072
LUXMAN 004
LXI 166 007 015 052 081 160 164
MAGNAVOX 164 059 197 003 060 061 004 063 064 127 022 160 094 239
226 273
MARANTZ 197 164 184
MATSUI 164
MAXENT 242
MEMOREX 007 072 004
METZ 088
MGA 197 004 024 028 042
MINERVA 088
MITSUBISHI 109 124 024 004 028 040 042 146 191
MTC 197 004 062 101
NAD 015 025
NEC 132 130 134 197 040 016 024 056 019 236 237 262 272
NIKEI 043
NUVISION 351
ONKING 043
ONWA 043
OPTONICA 019 081
OPTOMA 265 270
ORION 096
PANASONIC 034 056 080 092 164 208
PHILCO 197 003 059 060 064 164 004 024 056 063
PHILIPS 164 005 093 038 197 003 004 059 127 184 206 239 259
PIONEER 135 025 197 018 023 116 190 234 335
POLAROID 138 268 328 353 354 356 388
PORTLAND 004 143
PROSCAN 144 160 161 165 167
PROTON 004 131 058 143 171 173 193
QUASAR 034 056 092
RADIO SHACK 019 004 143 043 127
RCA 160 165 065 156 144 161 197 004 024 056 152 023 074 333
REALISTIC 007 019 043 047
ROCTEC 186
RUNCO 168 169 178 179 180 181 182 183 073 157 340
SAMPO 197 058 004 202
SAMSUNG 050 089 101 105 004 127 143 160 228 229 258
SANYO 166 007 020 053 057 082 187
SCEPTRE 276
SCOTT 028 043 004 048 143
SEARS 015 030 004 007 028 057 143 094 160 082 165 166
SELECO 189 200 205 227
SHARP 081 019 014 170 028 029 004 022 143 175 251
SIEMENS 088
SIM2 189 200 205 227
SIGNATURE 072
SOLE 231 232
SONY 070 139 147 126 185 194 085 213 277 279
SOUNDESIGN 028 004 003 043
SPECTRICON 112
SSS 004 043
48
CODE TABLES
BRAND CODE NUMBERS
47
BRAND CODE NUMBERS
TV
CODE TABLES
SUPRE MACY 002
SVA 328
SYLVANIA 197 003 059 060 063 064 164 044 160 127
SYNTAX OLEVIA 376
TANDY 081
TATUNG 056 062
TECHNICS 034 080
TECHWOOD 004
TEKNIKA 002 003 004 024 028 043 072 101 143
TELEFUNKEN 037 046 086 087
TELERENT 072
TERA 172
TMK 004
TOSHIBA 015 138 030 007 040 062 101 325
TOTEVISION 143
UNIVERSAL 008 009
VIDEO CONCEPTS 146
VIDIKRON 174 184 188 192 340
VIDTECH 004
VIEWSONIC 242
VIZIO 386 387
WARDS 004 008 009 019 028 060 061 063 064 072 074 143 164 034
WESTING HOUSE 076 280
WINBOOK 339
YAMAHA 197 004
YORK 004
YUPITERU 043
ZENITH 073 072 095 103 157 183 243 284
ZONDA 112
ABC 004 103 003 039 042 046 053
ADELPHIA 043 074
ADVANCED NEWHOUSE 043
ALTRIO 043
AMERICAST 099
ARCHER 005 007 014
ARMSTONG 074
AT&T BROADBAND 074
ATLANTIC BROADBAND 043 074
BELL SOUTH 099
BLUE RIDGE 043 074
BRESNAN 074
BRIGHT HOUSE 043 110
BUCKEYE COMM 074
CABLEVISION 043 074 108
CENTURION 092
CENTURY 007
CHARTER 043 074
CITIZEN 007
COGECO 074
COMBANO 080 081
COMCAST 043 074 110
COMSAT 074
COX DIGITAL 043 074
DIGICABLE 101
EAGLE 020 030 040
EASTERN 057 066
ECHOSTAR 106
ELECTRICORD 032
GEMINI 008 054
GENERAL ELECTRIC 072
GENERAL INSTRUMENT 074 103 104
GNC 099
GOLDEN CHANNEL 030
HAMLIN 049 050 055
HITACHI 103 055
INSIGHT 074
JERROLD 074 004 103 002 003 008 009 010 069
MAGNAVOX 010 012 064 079 095 094
MASSILLON 074
MEDIA ONE 107
MEDICOM 074
MEMOREX 052
MITSUBISHI 102
MOTOROLA 074 110 109 111
MOVIE TIME 028 032
MOXI 111
NCTC 074
NSC 015 028 038 071
OAK 031 037 053
PACE 043 074
PANASONIC 044 047
PARAGON 052
PHILIPS 006 012 013 020 085 095
PIONEER 043 103 034 051 063 076 105
PRUCER 059
PULSAR 052
RCA 047
RCN 074
RECOTON 098
CABLE / WEBTV
50
CODE TABLES
BRAND CODE NUMBERS
49
BRAND CODE NUMBERS
CABLE / WEBTV
CODE TABLES
REGAL 049 050
REGENCY 057
RODGERS 043
SAMSUNG 030
SCIENTIFIC ATLANTA 043 011 003 041 042 045 046
SEREN 043
SERVICE ELECTRIC 074
SHAW 074
SIGECOM 043
SONY 096 108
SPRUCER 047 078
STARCOM 002 004 008 009
STARGATE 008 030 097 104
SUSQUEHANNA 043 074
TIME WARNER 043 074
TOCOM 039 040 056
TOSHIBA 052
UNITED CABLE 004 053
UNIVERSAL 005 007 014 032 035
VIDEOTRON 043
VIEWSTAR 012 015 018 086 087 088 089
WIDE OPEN WEST 043 099
ZENITH 052 060 093 100
AIWA 146
ALPINE 098
APEX DIGITAL 087 111 115 112 116
ARCAM 122
CAMBRIDGE AUDIO 215
CARY AUDIO DESIGN 174
CLASSE 167
COBY 258
DENON 007 080 173
FUNAI 143
GATEWAY 175
GE 026 027
GO VIDEO 137 218 220 221 222
HARMAN KARDON 084 140
HITACHI 101
ILO 268
INTEGRA 142 180
JVC 012
KENWOOD 151
KISS 179 279
KLH 135
KRELL 104
LEXICON 148
LG 091 057 074
LITEON 264 265
MAGNAVOX 066 096
MALATA 267
MARANTZ 083 095
MERIDIAN 153
MITSUBISHI 017
MYRYAD 102 134
NAD 088 155
NAKAMICHI 103
ONKYO 076 035 180
OPPO 266
PANASONIC 021 042 138 139 144 150
PHILIPS 066 083 095 105 166
PIONEER 023 092 099 107 108 131
POLAROID 233 234 237
PRIMARE 193 194
PROCEED 086
PROSCAN 026 027
RCA 026 027
PJTECH 269
ROTEL 204
SAMSUNG 056 070 119 165 170 137 159
SANSUI 154
SANYO 147
SENSORY SCIENCE 222 223
SHARP 094
SONY 033 118 145 126 191
SYLVANIA 143
SYMPHONIC 143
TAG MCLAREN 156
TATUNG 102
TEAC 270
THOMPSON 026 027
THULE 177
TOSHIBA 035 034 130 141 164 188
VENTURER 149
DVD
52
CODE TABLES
BRAND CODE NUMBERS
51
BRAND CODE NUMBERS
DVD
CODE TABLES
VINC 161
YAMAHA 042 089 166 195 197
ZENITH 057 074 091
DVD-TV/DVD Combos
AIWA 146
FUNAI 143
SAMSUNG 165
SYLVANIA 143
SYMPHONIC 143
TOSHIBA 130
DVD-TV/DVD/VCR Combos
MAGNAVOX 143
PANASONIC 144
SYLVANIA 143
TOSHIBA 164
DVD-DVD/VCR Combos
GO VIDEO 137 218
PANASONIC 150
PHILIPS 105 (VCR Functions for VCR 067)
POLAROID 234
SAMSUNG 137 159
SANSUI 154
SONY 145 191
TOSHIBA 141
ZENITH 091 (VCR Functions for VCR171)
DVD-DVD Recorders
GATEWAY 175
GO VIDEO 220 221 222
ILO 268
KISS 279
LITEON 265
PANASONIC 139
SENSORY SCIENCE 222
SONY 191
TOSHIBA 188
VCR
AIWA 034 161
AKAI 016 146 043 046 124 125 142
AMPRO 072
ANAM 031
AUDIO DYNAMICS 012 023 039 043
BROOKSONIC 035 037 129
CANON 028 031
CAPEHART 108
CRAIG 003 040 135
CURTIS MATHES 031 041
DAEWOO 111 116 117 119 005 007 010 065 108 110 112
DAYTRON 108
DBX 012 023 039 043
DYNATECH 034 053
ELECTROHOME 059
EMERSON 006 029 035 017 025 027 031 034 036 037 046 101 129 131
138 153 162 116
FISHER 003 010 008 009
FUNAI 034
GE 031 072 147 063 107 109 144
GO VIDEO 132 136 155 040 115
GOLDSTAR 101 106 114 013 020 012 123
HARMAN KARDON 012 045
HITACHI 004 026 150 018 034 043 063 137 160 013
INSTANTREPLAY 031
JCL 031
JCPENNEY 012 013 015 040 066 101
JENSEN 043
JVC 048 043 130 150 055 060 012 031 050 152 166
KENWOOD 014 048 034 047
LG 101 106 114 013 020 012 123
LLOYD 034
LXI 034 003 009 017 106
MAGIN 040
MAGNAVOX 067 031 034 068 041 156 164
MARANTZ 067 069 012 031 156
MARTA 101
MATSUI 027 030
MEI 031
MEMOREX 101 003 010 014 031 034 053 072 102 134 139
MGA 045 046 059
MINOLTA 013 020
MITSUBISHI 059 061 151 013 020 045 046 051 142 049 168
MTC 034 040
MULTITECH 024 034
NEC 012 023 039 043 048
NORDMENDE 043
OPTONICA 053 054
ORION 025
PANASONIC 066 070 145 083 133 140 157 163 074 167
PENTAX 013 020 031 063
PHILCO 031 034 067
PHILIPS 031 067 034 101 054 071 156
PILOT 101
PIONEER 021 013 048
PORTLAND 108
PULSAR 072
QUARTZ 002 014
QUASAR 066 145 075
RADIO SHACK 123
54
CODE TABLES
BRAND CODE NUMBERS
53
BRAND CODE NUMBERS
VCR
CODE TABLES
RCA 107 109 144 147 158 041 145 013 020 140 034 040
REALISTIC 003 008 010 014 031 034 040 053 054 101
RICO 058
RUNCO 148
SALORA 014
SAMSUNG 102 104 113 115 112 120 032 040 066 107 109 122 125
SANSUI 022 043 048 135
SANYO 003 010 007 014 134 102
SCOTT 017 037 112 129 131
SEARS 003 008 010 014 081 013 101 009 017 073 112
SHARP 149 054 031 159 165
SHINTOM 024
SIGNATURE 034
SONY 056 057 058 077 052 003 078 076 031 149 154
SOUNDESIGN 034
STS 013
SYLVANIA 031 034 059 067
SYMPHONIC 034
TANDY 010 034
TATUNG 039 043
TEAC 034 039 043
TECHNICS 031 070
TEKNIKA 031 019 034 101
THOMAS 034
TMK 006
TOSHIBA 112 131 079 008 059 047 082 013 042 081
TOTEVISION 040 101
UNITECH 040
VECTOR RESEARCH 012
VICTOR 048
VIDEO CONCEPTS 012 034 046 141
VIDEOSONIC 040
WARDS 003 013 017 024 031 034 040 053 054 131
YAMAHA 012 034 039 043
ZENITH 072 080 056 048 101 034 058
VCR-TV/VCR Combos
DAEWOO 005 117
EMERSON 153
FUNAI 034
GOLDSTAR 101 123
HITACHI 034
JCPENNEY 101
LG 101 123
LLOYD 034
MAGNAVOX 034 067
MEMOREX 101
PANASONIC 070 167
PHILIPS 034 067
RADIO SHACK 123
RCA 034
SEARS 101
SONY 057 154
SYLVANIA 067
SYMPHONIC 034
THOMAS 034
ZENITH 034
AUDIO
ADC 007
ADCOM 082 092 225 161 269 355 356 366
AIWA 170 018 104 202 203 213 211 188
AKAI 138 189
AMC 125 126 127 128 258 281 282 038
AMEND 054
AMX 196
ANGSTROM 142
ANTHEM 335 336 337 338 339
ARCAM 141 418 419
ATLANTIC TECHNOLOGY 342
AUDIO ACCESS 147
AUDIO ALCHEMY 135
AUDIO DESIGN 194 221 011
AUDIO EASE 021 196 207
AUDIO FILE 071
AUDIO MATRIX 167
AUDIO SOURCE 273
AUDIO TECHNICA 134
B & K 096 097
BOSE 070 170 224 347 409 459 460 532
BOSTON ACOUSTICS 447
BRYSTON 023
CAMBRIDGE AUDIO 522
CARVER 006 028 061 071 201 214 226 180 185 022 029 077 284
CASIO 076
CHIRO 140
CINEMA SOUND 034 134
CITATION 148 272
CLARION 026
CLASSE 537
COMPAQ 382
CURTIS MATHES 076
DELPHI 415 515
DENON 002 034 109 215 229 230 027 037 234 259 330 340 341 349
350 400 401 402 444 564
EAD 466
EIGER 149
ELAN 057 290
ENLIGHTENED AUDIO 099 098
ESCIENT 368 381 451 452 453 454
FANFARE 352
FISHER 047 214 180 182 297
FLEXTRONICS 378
FOSGATE 062 231
FOSGATE AUDIONICS 342
GE 056 260
GOLDSTAR 008
HAFLER 174
HARMAN KARDON 231 233 254 153 154 118 121 227 277 317 318 365
HITACHI 020
IMERGE 371
INKEL 197
INTEGRA 354 438
JAMO 398
JBL 263
JCPENNEY 076 216
JEFF ROWLAND 206
JENSEN 058
JVC 240 163 191 114 266 279 291
56
CODE TABLES
BRAND CODE NUMBERS
55
BRAND CODE NUMBERS
AUDIO
CODE TABLES
KENWOOD 026 066 145 146 181 190 197 192 182 199 151 222 180 005
280 374 550
KINERGETICS 220 140
KLH 331
KOSS 216 573
KRELL 150 072 376 384
KYOCERA 007
LEXICON 120 235 236 237 357 358 359 360 361 362 363 364
LINN 124 377
LUXMAN 137 139 052 165 115 004 009
LXI 076 056
MAGNAVOX 086 164 152 208
MARANTZ 006 028 031 040 063 185 186 251 265 119 289 296 492
MCINTOSH 238 286
MCS 076
MERIDIAN 100 012 013
MITSUBISHI 242 243 204
MONDIAL 157 158 042 043 081 112
MYRYAD 276 293
NAD 186 113 283 478 479
NAKAMICHI 111 244 245 172 183 287
NEC 176
NIRO 343
NILES 403
ONKYO 017 046 064 107 108 187 079 080 090 179 209 270 275 438
OPTIMUS 026 041 138
OUTLAW 342
PANASONIC 032 195 219 177 292 383 516
PARASOUND 129 130 132 261 294 295 333 334
PHAST 196
PHILIPS 249 250 251 063 119
PIONEER 014 033 039 044 045 050 069 159 168 116 035 078 198 480
POLKAUDIO 029 515
PRIMARE 464
PROCEED 144 268
RCA 010 048 117 156 067 288
REALISTIC 019 056 073 075 095
REQUEST 351
REVOX 162
ROTEL 074 083 085
RUSSOUND 379 391 392
SAMSUNG 016 571
SANSUI 040 048 110 119 065 228
SANYO 047 059
SCOTT 019 091
SEARS 076
SHARP 026 094 131 175 181
SHERWOOD 024 038 055 102 103 105 106 051 030 447
SONY 018 093 223 247 248 160 166 015 101 184 218 271 353 369
372 380 417 421
SOUNDESIGN 036
SOUNDMATTERS 375
SOUNDSTREAM 084 088
SSI 068
SUMO 171
SUNFIRE 344 345 346 494
TAEKWANG 138
TEAC 005 019 049 111 212 217
TECHNICS 122 176 193 219 178 177 200 257 262
THETA DIGITAL 136
TOSHIBA 060 087 198 278
WARDS 180
YAMAHA 026 253 169 067 173 205 264 232 089 264 274 285 332 373
432 433
ZENITH 143 210
AUDIO-XM Radios & Tuners
BOSE 170 532
DELPHI 415 515
FANFARE 352
KENWOOD 550
POLKAUDIO 515
SONY 380
AUDIO
58
CODE TABLES
CD
BRAND CODE NUMBERS
57
BRAND CODE NUMBERS
SAT/DVR
CODE TABLES
SAT
CABLEVISION / VOOM 148
DIRECTV 173
ECHOSTAR / DISH 122 167 168
EXPRESSVU 122
GENERAL ELECTRIC 151 106 150
GENERAL INSTRUMENT 148
GOI 122
HITACHI 139 140
HTS 122
HUGHES 161 162 068 154 165 166 108 117
JVC 122
LG 170
MAGNAVOX 136
MEMOREX 136
MITSUBISHI 068 154
MOTOROLA 148
NEXT LEVEL 148
PANASONIC 142 160
PANSAT 172
PAYSAT 136
PHILIPS 152 153 156 068 154 136 108 117
PROSCAN 151 106 150
RADIOSHACK 148
RCA 151 106 150
SAMSUNG 123 155 163 169 175
SKY 164
SONY 103
STAR CHOICE 148
TOSHIBA 127 068 154 157 158
UNIDEN 136
ZENITH 159
DVR-PVR, TIVO
DISH 122
ECHOSTAR 122
HUGHES 108 117
HUMAX 117 118
JVC 122
PHILIPS 108 090 117
RCA 109
REPLAY NETWORKS 075
SONY 104 105
TIVO 090 117 118
TOSHIBA 117
ADCOM 062 042
AIWA 059 065 088 089 105 122 170 187
AKAI 085 195 202
AMC 231 232
AMEND 118
ARCAM 238
AUDIO ACCESS 119 147
AUDIO EASE 165
AUDIO TECHNICA 046
BSR 037 057
CALIFORNIA AUDIO 103 008
CAPETRONIC 063
CARRERA 057 080
CARVER 185 041 044 050 086 107 130 134 135 138 139 203 204 167
CASIO 111 182
CLARINETTE 182
CREEK 159
CROWN 035
DENON 002 123
EMERSON 042 069 102
FISHER 050 185 134 008
FRABA 111
GENEXXA 010 069 102
GOLDSTAR 080
HAITAI 093
HARMAN KARDON 018 033 047 208
HITACHI 042 175
INKEL 130 143 144
JCPENNEY 014 061 092 141
JENSEN 158
JVC 004 022 136 163 213 214 242 243
KENWOOD 185 007 023 055 071 072 142 137 254
KOSS 061
KRELL 241
KYOCERA 005
LOTTE 102
LUXMAN 011 028 070 076 249 252
LXI 059
MAGNAVOX 044 107
MARANTZ 027 041 044 051 077 107 209 246
MCINTOSH 212 247
MCS 014 073 092
MEMOREX 010
MISSION 044 107
MITSUBISHI 179
MITSUMI 153
MODULAIRE 182
MONDIAL 147
MYRYAD 244 155
NAD 006 005 067 178
NAKAMICHI 217 218 219 095
NEC 014 062
NIKKO 046
NSM 044 107
ONKYO 030 038 039 168 169
OPTIMUS 010 050 057 058 081 082 083 085 093 195
PANASONIC 103 201 172 008 068 248
PARASOUND 233 240
PHILIPS 041 044 107 246 253
PIONEER 010 020 025 056 174 175 176
60
CODE TABLES
BRAND CODE NUMBERS
59
BRAND CODE NUMBERS
CD
CODE TABLES
PROCEED 239
PROTON 044 107 228
QUASAR 103 008
RADIO SHACK 182
RCA 017 042 150
REALISTIC 042 050 051 102 181 182 187
ROTEL 044 107 161 178 250
SAE 044 107
SANSUI 044 069 107 128 171 190 125
SANYO 050
SCOTT 069 102
SHARP 026 031 051 066
SHERWOOD 003 019 051 096 112 115 119 166
SIGNATURE 033
SONY 048 081 097 126 133 177 225 226 164
SOUNDESIGN 251
SUMO 155
SYLVANIA 044 107
SYMPHONIC 052 181
TAEKWANG 195 085
TANDY 010
TEAC 015 034 036 051 052 101 131 140 079
TECHNICS 060 103 200 172 184 008 068
TECHWOOD 076
THETA DIGITAL 234 235
TOSHIBA 006 067 091 160 148
VECTOR RESEARCH 080
VICTOR 004 022 114 124
WARDS 185 033
YAMAHA 024 046 054 186 183 245
YORX 182
LDP
DENON 206 207
FUNAI 120
KENWOOD 152 013
MAGNAVOX 032 121
MARANTZ 211
MITSUBISHI 121
NAD 121
OPTIMUS 049 013
PANASONIC 113
PHILIPS 032
PIONEER 106 117 121
RADIO SHACK 120
RCA 002
REALISTIC 049
RUNCO 127
SANYO 075
SHARP 152 013
SONY 053 110
TECHNICS 113
THETA DIGITAL 032
TOSHIBA 152 106
YAMAHA 043 129
62
CODE TABLES
BRAND CODE NUMBERS
61
BRAND CODE NUMBERS
TAPE / PHONO / LIGHT
CODE TABLES
TAPE
AIWA 015 071 100 114
CARVER 006 008 027 024 036
DENON 105 227 229
FISHER 064
GOLDSTAR 011
HARMAN KARDON 233
JVC 106 116 239 240
KENWOOD 005 013 023 026 064 145 146 181 190
LINN 124
LUXMAN 035 137 139
MAGNAVOX 027
MARANTZ 014 027 056 065 087
MCINTOSH 238
MITSUBISHI 242 243
NAD 029 048
NAKAMICHI 244 245 025
ONKYO 002 012 016 017 018 019 115
OPTIMUS 026 054 055
PANASONIC 007 010 032 088 195
PHILIPS 027 087
PIONEER 003 039 047 050 066 098 222
QUASAR 007 088
SANSUI 027 113 119 224
SHARP 026 057 131 175 181
SHERWOOD 038 004 028 030 033 034
SONY 020 022 052 084 089
TEAC 009 059 212
TECHNICS 007 010 076 088 109 122 193
TOSHIBA 112
VICTOR 106
YAMAHA 021 026 031 067 040
PHONO
JVC 004
KENWOOD 005
PIONEER 003
YAMAHA 001 002
LIGHT
LITE-TOUCH 208 212
LUTRON 158 159 077
X-10 183 093
3M 152
AIWA 164
APPLE 401
ARCHER 155
AURORA MULTIMEDIA 220
AUTON 191
BOSE 409
CELADON 221
CRESTRON 213 214 215 216 217 218
DELL 261 262
DMX 156
DRAPER SCREEN 204
DREAMVISION 097
DWIN 080 253
EVERQUEST 206
EXTRON 151
FAROUDJA 184
FUJI 209
GATEWAY 261 262
HAUPPAUGE 294 295
HP 261 262
HUNTERDOUGLAS 219
JERROLD 153
JVC 185
KENSINGTON 406
KENWOOD 185
KEYSPAN 297
MAKITA 186 201
MICROSOFT 408 107
MINDPATH 205
NILES 160 187
NSM 161
PIANO DISC PLUS 085
POLKAUDIO 162
RUSSOUND 081
SCIENTIFIC ATLANTA 163 156
SIMA 082
SOLO ELECTRONICS 207
SOMFY 078 079
SONY 164 165 166 261 262
STARCOM 153
TURBOSCAN 167
VELODYNE 203
XANTECH 168 169 170 171 172 188 189
AUX-Media PC Controls
DELL 261 262
GATEWAY 261 262
HAUPPAUGE 294 295
HP 261 262
KEYSPAN 297
SONY 261 262
TOSHIBA 261 262
WINBOOK 261 262
AUX - XBox Controls
MICROSOFT/XBOX 408 107
AUX-iPod Controls
APPLE/iPod 401
AUX
64
NOTES
NOTES
63
BRAND CODE NUMBERS
AUX
CODE TABLES
BOSE 409
KENSINGTON 406
NOTES
6665
Frequently Asked Questions
OTHER INFO
Frequently Asked Questions
What is a “macro” button?
A “macro” is a button on the RF30 that you setup to make
a lot of things happen when you press it. For example, to
watch a DVD in most home theaters requires several
remote controls and many button presses (power up the
TV, power up the surround sound, power up the DVD
player, set the TV to the correct video input, set the
surround sound to the correct audio input and finally;
press play on the DVD player remote control).
Instead of pressing all of those buttons one at a time, the
RF30 enables you to setup one button that does all those
steps automatically with one press. For more information
on how and why you should setup macro buttons, watch
the Quick Setup DVD Program Guide or refer to pages
26-29 in this Manual.
If the batteries run out, will I lose my settings?
No. The RF30 stores all of your settings in non-volatile
FLASH memory. You could remove the batteries for
months, replace them at your convenience, and the RF30
would still remember your settings.
Who can I call for more answers?
The Universal Remote Control Technical Support and
Customer Service staff are ready to answer any questions
you might have.
Call us at 1-914-835-4484
Monday - Friday, 9AM to 6PM (EST)
Warranty
Universal Remote Control’s MastercontrolTMRF30 is
covered against any manufacturers defects or
workmanship for a period of one year from the date of
purchase if purchased from an authorized Universal
Remote Control dealer. Units purchased from online
auction sites or other unauthorized resellers have no
warranty. This warranty does not cover the following
items:
- Damage from misuse, neglect, or acts of nature
- Products that have been modified or incorporated
into other products
- Products purchased more than 12 months ago
- Units purchased from unauthorized dealers or
companies
Specifications
Learning Capability - 1200 IR commands at standard
frequencies (15kHz to 100kHz)
Macro Capability - 658 Macros of up to 190 steps each
IR Range (Line of Sight via Infrared): 30-50 feet, depending
on the environment
RF Range (radio frequency): 50 to 100 feet, depending
upon the environment
RF Frequency: 418MHz
Weight: 7.1 oz. (with batteries)
Size: 8.5”x 2.5”x 1”
Batteries: Four AAA Alkaline batteries included
LCD Size: 1.38” x 1.88”
Warranty/ Specifications
OTHER INFO
500 Mamaroneck Avenue
Harrison, NY 10528
Phone: 1-914-835-4484
FAX: 1-914-835-4532
www.universalremote.com
OCE-0046C_rev01
Loading...