Universal Remote UR3, SR3 User Manual

Universal Remote Control, Inc.
www.universalremote.com
UR3-SR3
Operating Manual
For Easy Clicker
1
This remote control is designed to operate most Digital and Analog Cable Boxes, as well as TVs, and a VCR or DVD player.
Introduction
Install two
AAA alkaline batteries
as shown here
1
Before you program or operate the remote control, you must install two new AAA alkaline batteries.
STEP1 Remove the battery compartment cover from the
back of your remote control.
STEP2 Check battery polarity carefully, and install the
batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.
Replacing Batteries
2
2
Button Functions
3
Programming the Remote Control.
4
A. Manual Pr
A. Manual Pr
ogramming
ogramming
The remote control can be programmed by entering a three­digit code number that corresponds to particular brands and models of equipment. The three-digit code numbers are listed in the code tables sections of this instruction manual.
*Note : In this section, when you are instructed to press a
[DEVICE] button, that means you should press either the CBL, TV, or DVD button, depending on which device you are programming the remote to operate.
3
STEP1 Turn on the equipment that you want the remote
control to operate Cable Box, TV and DVD(VCR).
STEP2 Press the [DEVICE] button and the [OK/SEL]
button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment
and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
*Note : You can verify that you have selected the correct
code by pressing the [MUTE] button. The equipment should turn on or off.
STEP4 Store the three-digit code by pressing the same
[DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
*Note : Try all the functions on the remote control. If any
of the functions do not operate as they should, repeat the instructions from Step 2 using the next three-digit code number from the same brand list.
B. Auto Sear
B. Auto Sear
ch Method
ch Method
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:
STEP1 Turn on the equipment that you want the remote
control to operate (Cable Box, TV, VCR, or DVD).
4
STEP2 Press the [DEVICE] button and the [OK/SEL]
button simultaneously for three seconds. The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on.
STEP3
Press the [CH] or [CH] button one at a time or
keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release the [CH] or [CH] button as soon as the equipment turns off.
*Note : You can verify that you selected the correct code
by pressing the [MUTE] button. The equipment should turn On or Off.
STEP4 Press the same [DEVICE] button to store the
code. The Device LED will blink twice to confirm that the code has been stored.
C.
C. TT
o find the Thr
o find the Thr
ee-Digit Code that W
ee-Digit Code that Wasas
PrProgrammed using the Auto Sear
ogrammed using the Auto Searchch
Method
Method
STEP1 Press the appropriate [DEVICE] button and the
[OK/SEL] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [INFO] button. The device LED will blink
a number of times indicating the number of each digit for the code. Each digit is separated by a one second interval of the LED being off.
Example : One blink, then three blinks, then eight blinks
indicates the code number 138.
*Note : Ten blinks indicates the number 0.
D.
D.
PrProgramming a Second TV to the DVD Button
ogramming a Second TV to the DVD Button
5
STEP1 Press the [DVD] button and the [OK/SEL] button
simultaneously for 3 seconds. The DVD LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [TV] button.
STEP3 Point the remote control toward the TV and enter the
three-digit code for your TV from the TV codes table.
STEP4 Store the three-digit code by pressing the [DVD]
button. The device LED will blink twice to confirm that the code has been stored.
E. Pr
E. Pr
ogramming for Advanced Functions.
ogramming for Advanced Functions.
In the CABLE device mode, the A,B,C,D and blank macro buttons can be programmed to act as a 'Macro' or Favorite Channel button. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed with ONE button press.
*Note : The A,B,C and D buttons are not programmable
if you have a Digital Cable Box made by Pace, Pioneer or Scientific-Atlanta.
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL] button
simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.
STEP3 Enter the the 2, 3 or 4-digit code for the channel you
want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example,
050), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered.
STEP4 Press the [CH
] button to store the channels that were selected. The [CBL] button will blink twice to confirm the storage of commands.
6
To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel.
To erase the Macro programming and return to the original function:
STEP1 Press the [CBL] button to select the CABLE mode.
STEP2 Press a [MACRO] button and the [OK/SEL] button
simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP3 Press the [CH] button to erase the functions stored
in the button. The CBL device LED will blink twice to confirm that the memory button has been erased.
FF.
.
Assigning the V
Assigning the V
olume and Mute keys to a
olume and Mute keys to a
Dif
Dif
fer
fer
ent Device
ent Device
By default, the VOL, VOLand MUTE keys operate through your TV. If you would like those keys to operate those functions on a different device, follow these steps.
STEP1 Press the [OK/SEL] button and [CBL] button
simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on.
STEP2 Press the [VOL
] button. The device LED will
blink.
STEP3 Press the [DEVICE] button corresponding to the
device that you would like the volume and mute buttons to control. The device LED will blink twice to confirm the programming.
Example : If you wish to have the volume and mute keys
operate your Cable Box, press the [CBL] button in Step3.
Loading...
+ 16 hidden pages