Universal Innovations Sahara X450 User Manual
X4 50 Barbecue
Photograph is not to scale. Specication
subject to change without prior notice.
• For outdoor use only.
• Read instructions before using the appliance. Failure to follow instructions could result in
death, serious bodily injury, and/or property loss.
• Warning: accessible parts may be very hot. Keep young children away.
• Do not move the appliance during use.
• Turn o the gas supply at the gas bottle after use.
• Any modication of the appliance, misuse, or failure to follow the instructions may be
dangerous and will invalidate your warranty. This does not aect your statutory rights.
• Retain these instructions for future reference.
• Leak test your barbecue annually. Check the hose connections are tight and leak test each
time you reconnect the gas bottle
WARNING
FOR YOUR SAFETY FOR YOUR SAFETY
IF YOU SMELL GAS:
1. Shut o gas to the appliance. 1. Do not store or use petrol or other ammable vapours or
2. Extinguish any open ame. liquids in the vicinity of this or any other appliance.
3. Open barbecue lid or hood. 2. A gas bottle not connected for use shall not be stored in the
4. If odour continues, discontinue use and vicinity of this or any other appliance.
contact your local dealer.
Universal Innovations
Manufactured by
www.uigroup.ie
Parts Supplied
Ref Description Illustration Qty Ref Description Illustration Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Large Wheel
Castor
Wheel
Cabinet
Base
Cabinet
Base Plate
Cylinder
Rack
Left + Right
Side Wall
Cabinet
Front Panel
Cabinet
Brace Plate
Heat Shield
Rear Cross
Bar
Front Cross
Bar
Sink + Hood
Assembly
2
2
1
1
1
1
1
1
1
1
1
1
Hose
Assembly
Left Side
Shelf
Right Side
Shelf
Vaporising
Bars
Cooking
Grill
Warming
Rack
Rotisserie
Motor
Bracket
Rotisserie
Handle
Bracket
Rotisserie
Motor
Rotisserie
Bar
Rotisserie
Skewers
Rotisserie
Handle
1
1
1
4
4
1
1
1
1
1
2
1
2
3
M6x12
Bolt
M6x16
Bolt
M6 Washer
M4x10
Bolt
35
4
4
8
Tools Required For Assembly
• Allen Key (supplied)
• Adjustable Spanner
Before You Start
• Check the contents of the box and make sure you have all the parts and ttings listed. If not,
contact our Helpline on 00 353 1 2873797 and we will be able to help you.
• When you are ready to start, make sure that you have plenty of space and a clean dry area
for assembly.
• Before cooking on this barbecue, turn the barbecue on at the medium to high temperature
and burn for 30 minutes to allow curing of vaporising bars and to burn o cleaning residue
materials.
Assembly
• Please lay out all nuts and bolts and check lengths before assembly. It is recommended that
the carton is cut open and spread out on the oor and used as a protective surface during
assembly. Refer to the assembly diagrams as necessary.
• Important - while every precaution has been made in the manufacture of this product, care
must be taken during assembly in case sharp edges are present.
• Remove all transit packaged parts from the inside of the grill body before assembling.
Important - follow gas leak test advice before use. Ensure all connections are tight and secure.
• This product is for OUTDOOR USE ONLY.
• NEVER use indoors, in an enclosed area or below ground level.
• This barbecue is intended for use with LPG bottled gas only. (A regulator of 28mbar must be
used for Butane gas or 37mbar for Propane gas).
• NEVER use an adjustable regulator with this barbecue.
Parts Supplied
Ref Description Illustration Qty Ref Description Illustration Qty
25
26
A
B
C
D
Rotisserie
Rotating
Sleeve
Grease Tray
1
1
Fixings Supplied
4
Assembly Step 1
Fit large wheels to the cabinet base using the pretted washers and R-clips. Fit castor wheels to
the cabinet base using 6 M6x12 bolts (Ref A).
Large Wheel
Castor Wheel
NOTE: Order of xings
on large wheels
M6x12 Bolts (Ref A)
M6x12 Bolts (Ref A)
M6x12 Bolt (Ref A)Cabinet Base
5
Assembly Step 2
Fit left and right side walls using 4 M6x12 bolts (Ref A) along the bottom of each wall. Note: make
sure large wheels are on the left hand side.
Left + Right Side Wall
M6x12 Bolt (Ref A)
M6x12 Bolts (Ref A)
1. Fix cabinet front panel at the six points as shown below using 6 M6x12 bolts (Ref A). Note: an
extra person will be needed to hold the door in position while tightening xings.
2. Fix cabinet brace plate to right side (behind big wheel) using 4 M6x12 bolts (Ref A).
Cabinet Front Panel
Cabinet Brace Plate
1.
2.
M6x12 Bolt (Ref A)
6
Assembly Step 3
7
Assembly Step 4
Turn barbecue cabinet base over (large wheels on left hand side). Position cabinet base plate and
cylinder rack as shown. Note: place cabinet base plate rst. Use 4 M6x16 bolts (Ref B) and 4 M6
Washers (Ref C) to secure cylinder rack and one side of cabinet base plate. Use 2 M6x12 bolts
(Ref A) to secure other side of base plate.
Cabinet Base
Plate
Cylinder Rack
M6x16 Bolts (Ref B)
M6 Washers (Ref C)
M6x16 Bolts (Ref B)
M6 Washers (Ref C)
M6x12 Bolts (Ref A)
Cabinet Base Plate
Cylinder Rack
M6x12 Bolt (Ref A) M6x16 Bolt (Ref B)
M6 Washer (Ref C)
Loading...