Universal Innovations Provence User Manual

Dear Customer,

We tried to achieve two targets when developing this product.
The  rst was to produce the best quality heater on the market.
The second was to produce the most cost-e ective heater.
We feel that we have achieved these two objectives however we
would be delighted to hear from you if you have any comments.

Thank you for purchasing one of the products in our
range. We wish you many enjoyable warm hours.

Yours Sincerely

Chairman

The Provence gas stove is made by Universal Innovations. It is made to an

exacting quality standard and is covered by the following guarantee:

THIS PRODUCT IS FULLY GUARANTEED FOR 2 YEARS,

REGARDING PROPER USE.

This guarantee does not a ect your statutory rights in any way.

HELPLINE Dublin Ireland

00 353 1 2873797 or at www.uigroup.ie

IF YOU NEED ANY ASSISTANCE PLEASE DO NOT HESITATE TO CONTACT US

DIRECTLY AT THE FACTORY. DO NOT BRING GOODS BACK TO PLACE OF

PURCHASE.

PROVENCE

Flueless Gas Stove

User Manual

manufactured by

manufactured by

Read these instructions before using the appliance.

When lighting for the  rst time, burn outdoors for 4 hours minimum to cure the synthetic coals.
(The coals give o an odour when curing).
The appliance must be installed and used in accordance with the regulations, which are currently in force.
The heater should be positioned on a level surface. Only use in a well ventilated area.
The minimum room size when using this appliance is 64 cubic metres with a minimum ventilation of
80 cm squared area.

To fi t a Butane Gas Regulator:

Attach regulator to end of hose and secure with hose clip.
Note: for ease of  tting hose, lubricate ribbed nipple of regulator with a soap solution.

To fi t a Butane Gas Cylinder:

(Ensure that the area is free from any unprotected combustible material or substance)

1. The changing and connection of LPG cylinders must be undertaken in a  ame free atmosphere.

2. Attach the regulator to the new cylinder. Ensure that the hose is not twisted or damaged in any way.

3. Use gas cylinders with a gas capacity of 7-15kgs.

4. In order to remove the regulator you must ensure that the regulator is in the “o ” position.

Before lighting:

1. Inspect the hose assembly. If the hose is cut or shows signs of excessive wear, or is leaking it must
be replaced prior to operation of the heater.

2. Ensure the heater is positioned with a minimum clearance above and beside
of 0.6metres from  ammable materials both ver tically and horizontally.

3. Ensure that the stove door is closed securely.

To Light Heater:

1. Fit battery type AA provided into ignition button (“+“ side up). See Fig.1.
Remove battery during periods of non-use to prevent battery leak.

2. Turn on gas supply at gas cylinder regulator.

3. Push control knob down and turn the control knob to the position and
at the same time, press sparker button to light the pilot.

4. If there is no spark check the battery type AA is correctly  tted. (the pilot  ame can be viewed at the
right hand side of the coal bed).

5. If pilot does not light turn control dial to position. Wait one minute and repeat step 3. Do not
continuously hold down the control knob as you may cause a build up of gas.

6. Once the pilot is lit hold down the control dial for at least 10 seconds until the main burner lights.
Operate the  re between the high and low  ame settings as required.

7. If the pilot and main burner do not stay lit on releasing the control knob, turn the control knob to
the ignition position and repeat steps 3 to 4.

8. The is a pilot setting only.

To Turn Off Heater:

1. Turn the control knob to position.

2. Turn o the gas at the cylinder regulator valve.

NOTE: The pilot light will remain alight until the cylinder regulator is turned o .

3. Disconnect the regulator from the cylinder when the heater is not in use.

4. Remember to remove battery during periods of non-use to prevent battery leak.

Important: Read all of the instruction Manual before using this appliance . This appliance must

be installed in accordance with such regulations as are in force. Installation to be carried out by a
competent person.

Warning: The guard (glass door) on this appliance is to prevent risk of  re or injury from burns and

no part of it should be permanently removed. IT DOES NOT GIVE FULL PROTECTION FOR YOUNG
CHILDREN OR THE INFIRM. For the full protection of young children or the in rm, we recommend a
 reguard conforming to BS 8423 be  tted.

Do not: Attempt to use the heater in high rise  ats, basements, bathrooms or bedrooms.
Do not: Use any other gas except Butane.
Do not: Attempt to clean the heater until it is turned o and fully cooled.
Do not: Use naked  ame to detect suspected gas leaks.
Do not: Allow children or pets to play near the heater.
Do not: Twist the  exible gas hose.
Do not: Touch the glass panel or front and sides of the unit while the heater is operating. Allow the

unit to cool down for one hour before touching the front or sides

Do not: Use in leisure vehicles such as caravans and auto caravans.
Do not: Position the appliance close to walls, furniture, hangings, net curtains, bed linen and other

in ammable materials as this would result in the risk of  re.
In the event of a gas leak. ie. If you smell gas, turn o the cylinder valve. Disconnect the cylinder, take
it outdoors and contact a competent service technician.

Warning:

Never attempt to light the unit if the hose is loose or damaged in any way. Also never attempt to light
the unit if you have reason to believe that the unit may be leaking gas. In the event of a gas leak turn
o the gas supply at the cylinder and have the unit fully checked by a competent person in accordance
with the instructions enclosed. We recommend servicing after every 1000 hours of use. Should you
need to change the gas bottle, con rm that the gas supply is turned o at the cylinder and that there
are no sources of ignition near before proceeding.

Do: Place heater on a  at, level and solid sur face at all times.
Do: Leak test the unit after long periods of storage.
Do: Wait for 3 minutes before relighting, if the burner  ame becomes extinguished during use.
Do: Ensure that all naked  ames are extinguished before  tting a new cylinder.
Do: Store gas cylinders outdoor, above ground level in a safe and secure environment.
Do: Make sure that the gas supply at the gas cylinder is turned o after use.
Do: Ensure that servicing of the unit is carried out by a competent person in accordance with the

instructions enclosed.

Do: Allow the unit to cool down for one hour before touching the front or sides.

Always: Follow any safety instructions supplied with gas cylinders.
Always: Keep unit well away from glass doors and windows to ensure no possibility of heat build up

and damage.

Always: We recommend servicing once a year or after a prolonged period of non-use.
Always: Ensure that there is no blockage of air ow. For example sooting and poor burning can be

caused by dirt, insects, cobwebs, blocking the air ow to/in the burner.

Cleaning:

Abrasive cleaners are not to be used. Clean unit with a damp cloth when fully cooled.

Gas Cylinders:

This unit is designed for use with a 7kg or 15kg (UK) and 11.4kg gas cylinder (Eire).

Do Not Bring Goods Back To Place Of Purchase.

For help, contact our website www.uigroup.ie or our factory helpline.

Helpline hours: 9am - 5pm Monday to Friday. Ph: (00 353) (1) 2873797.

GUARANTEE

USER INSTRUCTIONS

SAFETY INSTRUCTIONS

Technical and servicing information:

This appliance is designed for indoor use only using Butane gas at a supply pressure of 28-30
millibar and must be serviced by a fully quali ed and competent CORGI registered engineer in
accordance with the instructions included.
Please read all accompanying documentation carefully.

Technical Specifi cations:

Overall height: 840 millimetres approximately
Overall width: 570 millimetres approximately
Heat input: 3.0kW (Gross)
Gas consumption: 215 grams per hour at maximum setting
Gas category: I3B
Gas type & Supply pressure: Butane 28-30 mbar
Injector size: 0.82 mm
Cylinder sizes: 11.34kg cylinder (Eire) and 15kg or 7kg cylinder (U.K)
Hose: BS3212 length 40 cm
Destination Countries: GB & IE

The product is fully guaranteed for two years regarding proper use.
This guarantee does not a ect your statutory rights. For servicing contact your local gas
supplier. Servicing to be carried out by a quali ed, competent registered gas engineer before
the start of every heating season.

Call 0800 662 663 to speak to you nearest Calor retailer and to order gas.
Call [phone] if calling from ROI.
Visit calor.co.uk and click on ‘Order Gas’

For help on this product and our range of products see our website www.uigroup.ie or contact
the factory direct on our Helpline 00353 1 2873797.

Helpline hours are 9am to 5pm Monday to Friday.

We are located at: Universal Innovations Ltd.
Kilcoole Industrial Estate,
Kilcoole,
Co. Wicklow,
Ireland.

0086

ASSEMBLY INSTRUCTIONS - IN 3 EASY STEPS

If you require any further assistance please do not hesitate to contact us directly at the factory.

HELPLINE DUBLIN IRELAND: Ph: 00 353 1 2873797, Fax: [phone]

(place battery “+“ side up)

TECHNICAL & SERVICING INFORMATION PARTS LIST

HOW TO ORDER

Parts orders may be placed by contacting us directly at the factory at 00353 1 2873797, by post at
Universal Innovations, Kilcoole Industrial Estate., Kilcoole, Co. Wicklow, Ireland. Or by emailing

us at [e-mail]

Please include the following details:

• Model Name

• Serial Number

• Kilowatt Rating

• Month and Year of Purchase

• Name and Location of Retailer

• Your Name, Address and Contact Number

ALTHOUGH EVERY PRECAUTION HAS BEEN TAKEN TO ELIMINATE SHARP EDGES ALWAYS TAKE CARE WHEN

HANDLING METAL COMPONENTS.