Universal Furniture 988634, 987634, 987635, 988635 Assembly Instruction Manual

Assembly Instruction General Side/Arm Chair 987634/635&988634/635

2 SET

#1

#4

#5

#3

#2

A

B
C

Parts List

UPHOLSTERY SEAT
WITH SEAT FRAME

BACK FRAME

WRENCH

Hardware List

BOLT+SPRING WASHER+FLAT WASHER--1/4" Dia

4 SETS

1 PC

2 PCS

1 PC

3" L

QTY

QTY

#6

ARM

1 pair

1-3/4" L

D

FOR BOTH
SIDE CHAIR
&
ARM CHAIR

ONLY
ARM CHAIR

BOLT+SPRING WASHER+FLAT WASHER--1/4" Dia

WOOD SCREW

BOLT+SPRING WASHER+FLAT WASHER--1/4" Dia

2 SETS
2 SETS

1-3/4" L

2-1/2" L

BOLT+SPRING WASHER+FLAT WASHER--1/4" Dia

4 SETS

1 PC

FRONT LEG

1-1/2" L

NO.

THANK YOU FOR PURCHASING THIS QUALITY PRODUCT. BE SURE TO CHECK ALL PACKING MATERIAL

CAREFULLY FOR SMALL PARTS THAT MAY HAVE COME LOOSE INSIDE THE CARTON DURING SHIPMENT.
CAUTION: (1) THESE PARTS ARE CUMBERSOME AND HEAVY. THIS PRODUCT CAN BEST BE ASSEMBLED WITH
THE ASSISTANCE OF ONE OR MORE PERSONS IN ORDER TO PREVENT PERSONAL INJURY AND TO INSURE
PARTS ARE NOT DAMAGED DURING THE ASSEMBLY PROCESS. IF DIRTY, CLEAN FINISHED PARTS WITH MILD
DISHWASHING LIQUID AND WATER SOLUTION APPLIED ON DAMP CLOTH. CLOTH SHOULD NOT BE
EXCESSIVELY WET. POLISH FINISH WITH SOFT CLOTH AND AN INDUSTRY RECOGNIZED FURNITURE POLISH.

(2) TO PREVENT DAMAGE TO YOUR FLOOR OR CARPET, PLEASE CHECK THE BOTTOM OF EACH PIECE
OF FURNITURE FOR STAIN RESIDUE AND ROUGH SURFACES AND ALSO CHECK FOR STAPLES OR NAILS LEFT
AFTER REMOVING THE PACKAGING MATERIAL. THE MANUFACTURER WILL NOT BE HELD RESPONSIBLE IF
PREVENTATIVE STEPS ARE NOT TAKEN PRIOR TO INSTALLATION.

(3) UNPACK AND DISPOSE OF ALL PACKING MATERIAL BUT BE CAREFUL NOT TO THROW AWAY ANY
ASSEMBLY PARTS OR HARDWARE. READ THE INSTRUCTION SHEET AND PARTS LIST CAREFULLY. REMOVE
ALL STAPLES AND SCREWS USED FOR PACKAGING CAREFULLY USING PLIERS AND OR SCREWDRIVERS TO
PREVENT INJURY AND SCRATCHING OR DAMAGING FLOORING.

(4) DURING NORMAL USE EVERYDAY, SCREWS, BOLTS, NUTS AND WOODEN PLUGS MAY LOOSEN UP.
THEY SHOULD BE PERIODICALLY INSPECTED AND RE-TIGHTENED TO PREVENT DAMAGE TO THE FURNITURE
AND (OR) PERSONAL PROPERTY OR CAUSE INJURY. ALWAYS CHECK TO BE SURE ALL HARDWARE ON THIS
LIST AND THE ABOVE MENTIONED COMPONENTS IS ATTACHED TO THE FURNITURE PROPERLY AND KEPT
TIGHTENED AT ALL TIMES.

Parts and Hardware List:

ASSEMBLY STEPS:

TOOLS REQUIRED: WRENCH # 4 (See Hardware List). AND PHILLIPS HEAD SCREWDRIVER (NOT PROVIDED)
NOTE: FIRST READ THE CHAIR LEVELING INSTRUCTIONS. THIS IS AN ADDITIONAL ASSEMBLY SHEET FOUND INSIDE THE

CARTON. PLACE ALL CHAIR PARTS ON A CLEAN, CUSHIONED AREA TO PREVENT SCRATCHING THE FURNITURE.

ASSEMBLY PROCEDURES:

1. PLACE THE UPHOLSTERED SEAT CUSHION (A) UPSIDE DOWN ON A CLEAN, SOFT SURFACE.

2. REMOVE THE PLASTIC COVER ON THE UPHOLSTERED SEAT (A). ASSEMBLE THE BACK FRAME (B) TO THE

BACK RAIL OF THE SEAT FRAME (A) USING ----- # 1 (BOLT + SPRING WASHER + FLAT WASHER).

3. ATTACH THE REAR CORNER BLOCKS OF THE SEAT FRAME (A) TO THE BACK LEGS AND FRAME

(B) USING ----- # 2 (BOLT+ SPRING WASHER + FLAT WASHER).

4. ASSEMBLE FRONT CORNER BLOCKS OF SEAT FRAME WITH THE FRONT LEGS (C) USING ----- #3 (BOLT +

SPRING WASHER + FLAT WASHER). THEN TIGHTEN ALL BOLTS COMPLETELY USING THE WRENCH # 4.

5. (FOR THE ARM CHAIR ONLY) ATTACH THE END OF BOTH ARMS (D) TO THE BACK POST (B) USING

SCREWS----- # 5 . NEXT ATTACH THE ARM POST (D) TO THE SIDE RAIL OF THE SEAT FRAME (A) USING -----

Assembly Instruction General Side/Arm Chair 987634/635&988634/635

ONLY ARM CHAIR

C

A

#3

#2

#1

#5

#6

D

B

#6 (BOLT + SPRING WASHER + FLAT WASHER).

6. AFTER MAKING SURE ALL BOLTS ARE ATTACHED AND HAND TIGHTENED, TURN THE CHAIR OVER.

7. LEVEL THE CHAIR FOLLOWING “CHAIR LEVELING INSTRUCTION”. THIS IS AN ADDITIONAL ASSEMBLY

INSTRUCTION SHEET FOUND INSIDE THE CARTON.

8. MAKE SURE THE CHAIR IS LEVEL AND THEN TIGHTEN ALL BOLTS COMPLETELY USING THE WRENCH

SUPPLIED.