Universal Electronics 8881 R User Manual

www.insigniaproducts.com

Getting Started NS-32E859A11/NS-42E859A11

Remote control

# Button Description

(power)

Press to turn on your TV. Press again to put your TV in standby mode. When your TV is in standby mode, power still flows through it. To

completely disconnect power, unplug the power cord.

DVD

Press to control a DVD player. You must program the remote control before this button works. For more information, see “Programming your universal Insignia remote control” on page 27.

TV Press to put the remote in TV mode.

APPS Press to open the Apps screen in the on-screen menu.

TiVo Press to open the on-screen menu.

GUIDE

Press to open the program guide. For more information, see “Displaying additional information” on page 35.

SELECT Press to confirm selections or changes.

! " # $

Press to move left, right, up, or down in on-screen menus.

ZOOM

Press to select the aspect ratio. For more information, see “Adjusting the video settings” on page 40.

EXIT Press to close the on-screen menu.

(thumbs down)

Press to decrease the thumbs rating by 1 thumb. In the channel list, press to remove a highlighted channel from the

favorite list. In the on-screen keyboard, press to switch to lowercase letters.

VOL+/VOL– Press to increase or decrease the volume.

FAV

Press to open the favorite channel list. For more information, see “Setting up the channel and favorite channel lists” on page 63 and “Viewing a favorite channel” on page 64.

MUTE Press to mute the sound. Press again to restore the sound.

/SLOW

Press to enter slow motion playback in TV VOD mode (watching Netflix and CinemaNow) or when using a DVD player, Blu-ray player, or DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

Press to turn the video window on or off. For more information, see “Turning the video window on or off” on page 43.

(replay)

Press to jump back eight seconds in TV VOD mode (watching Netflix and CinemaNow) or when using a DVD player, Blu-ray player, or DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

(pause)

Press to pause playback in TV VOD mode (watching Netflix and CinemaNow) or when using a DVD player, Blu-ray player, or DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

www.insigniaproducts.com

NS-32E859A11/NS-42E859A11 Getting Started

(fast-reverse)

Press to fast-reverse in TV VOD mode (watching Netflix and CinemaNow) or when using a DVD player, Blu-ray player, or DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

(stop)

Press to stop playback in TV VOD mode (watching Netflix and CinemaNow) or when using a DVD player, Blu-ray player, or DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

$ (play)

Press to start playback in TV VOD mode (watching Netflix and CinemaNow) or when using a DVD player, Blu-ray player, or DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

CLEAR Press to clear character input in the on-screen keyboard.

AUDIO

Press to select Audyssey Dynamic Volume, SRS TruSurround HD, Audio Only, Treble, Bass, or Balance. For more information, see “Manually adjusting audio settings” on page 44.

PICT

Press to adjust the video settings. For more information, see “Adjusting the video settings” on page 40.

STB

Press to control a set-top box. You must program the remote control

before this button works.

For more information, see “Programming your

universal Insignia remote control” on page 27.

AUX

Press to control auxiliary devices, such as amplifiers or

receivers. You

must program the remote control before this button works. You need to program the remote control to control connected devices. For more information, see “Programming your universal Insignia remote control” on page 27.

INPUT

Press to open the input source list, then press ! or " to cycle through the available input sources. For more information, see “Selecting the video input source” on page 33.

LIVE In menu mode, press to return to full-screen video TV mode.

INFO

Press to display TV status information, such as the channel number, channel name (if available), or signal source. For more information, see “Displaying additional information” on page 35.

In the channel list, press to rename the highlighted channel. For more information, see “Setting up the channel and favorite channel lists” on page 63.

MENU Press to open the on-screen menu.

(thumbs up)

Press to increase the thumbs rating by 1 thumb. In the channel list, press to add a highlighted channel to the favorite list. In the on-screen keyboard, press to switch to uppercase letters.

VOD

Press to access the VOD (video on demand) on-screen menu to watch video services offered through your connected TV, such as Netflix, CinemaNow, etc.

# Button Description

CH!/CH"

Press to change channels. For more information, see “Selecting a channel” on page 34.

LIST/DVR

Press to see the list of all the recorded programs in a DVR/STB that is set up with your remote control. You need to program the remote control to control connected devices. For more information, see “Programming your universal Insignia remote control” on page 27.

LAST Press to go to the last viewed channel in TV mode.

(advance)

Press to jump forward to the next segment in TV VOD mode (watching Netflix and CinemaNow) or when using a DVD player, Blu-ray player, or DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

(fast-forward)

Press to fast-forward in TV VOD mode (watching Netflix and CinemaNow) or when using a DVD player, Blu-ray player, or DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

(record)

In DVR mode, press to record a program. You need to program the remote control to record from the DVR. For more information, see “Programming your universal Insignia remote control” on page 27.

A B C D

Provides an enhanced interface for attached device (such as a DVR), Internet applications, and TiVi search features.

Numbers

Press to enter channel numbers, the parental control password, or characters.

When programming the remote control, press to enter device and programming codes.

SLEEP/—

Press to enter a digital sub-channel number in Live TV mode. In other modes, press to set the sleep timer. You can select

Cancel, 5,

10, 15, 30, 60, 90 minutes and 2, 3, 4 hours. For more information, see

“Setting the sleep timer” on page 76.

ENTER

Press to confirm selections or changes.

Press to turn closed captioning on or off. For more information, see “Using closed captioning” on page 71.

# Button Description

www.insigniaproducts.com

Getting Started NS-32E859A11/NS-42E859A11

Using the remote control

Installing the remote control batteries

To install the remote control batteries:

1 While pressing the release button on the battery

compartment cover on the back of the remote, lift the cover off the remote.

2 Insert two AA batteries into the battery compartment.

Make sure that you match the + and – symbols on the batteries with the + and – symbols in the battery compartment.

3 Replace the battery cover.

Making connections

Connecting the power

To connect the power:

• Plug the power cord on back of your TV into a power outlet.

Cautions

• Batteries should not be exposed to excessive heat, such as sunshine, heat registers, or fire.

• Battery chemicals can cause a rash. If the batteries leak, clean the battery compartment with a cloth. If chemicals touch your skin, wash immediately.

• Make sure that batteries are disposed of correctly. Do not burn or incinerate.

Cautions

• Make sure that you use the correct type of power. See the label on your TV.

• If you do not intend to use your TV for an extended period of time, unplug the power cord from the power outlet.

www.insigniaproducts.com

NS-32E859A11/NS-42E859A11 Getting Started

Turning on your TV for the first time

Per Dana’s instructions, the graphics and text in this section were based on comments for the QSG. Please verify if additional changes need to be made.

The first time you turn on your TV, the Setup Wizard opens. The Setup Wizard guides you through setting up basic settings. You can skip these settings or press EXIT,

MENU, or LIVE on your

remote control to exit the wizard (except when a software update is in progress).

To set up your TV:

1 Make sure that you have:

• Installed the remote control batteries. (See page 16 for details).

• Connected an antenna, cable TV, or satellite TV. (See page 17 for details.)

• Connected to your home network, if available. (See page 24 for details).

• Connected the power cord. (See page 16 for details.)

2 Press (power) to turn on your TV. The Welcome screen

opens.

3 Press ! or " to highlight Set up this TV, then press SELECT.

The Remote Control Connection screen opens.

4 Press and on your remote control to pair the remote

control.

Note

Unless otherwise noted, all tasks in this section are based on using the remote control.

Welcome

Set up this TV

Skip for now

You are about to begin Guided Setup, which prepares the Insignia HD TV for your use. This typically takes less than 10 minutes.

(If you skip Guided Setup now, you can set it up later by pressing TIVO and choosing Settings > Help > Reset this TV > Repeat Guided Setup.)

for retail mode

Remote Control Connection

Cancel (use IR instead)

To set up your remote control to use RF (radio frequency) to communicate with your TV, hold down the THUMBS UP and THUMBS DOWN buttons at the same time for 5 seconds. This will mean you won’t need to point the remote control directly at the TV.

old down the THUMBS UP and THUMBS DOWN buttons for 5 seconds

www.insigniaproducts.com

Getting Started NS-32E859A11/NS-42E859A11

5 The Network Setup screen opens. Press ! or " to highlight

your network connection type, then press SELECT and follow the on-screen instructions to set up your network and run the network speed test.

6 The Setup Channels screen opens. Press ! or " to highlight

your signal type, then press

! or " to start the channel

scan. If you use a cable or satellite TV box,

you do not need

to scan for channels

7 If you connected to a network in Step 5 and a software

update is available, the Update in Progress screen opens.

Follow the on-screen instructions to install the software update.

8 The Date and Time Setup screen opens. Press ! or " to

highlight Use this date and time, then press SELECT. OR

Press

! or " to highlight Set date and time manually,

then press

! or " and follow the on-screen instructions to

set your time zone, daylight saving option, and date and time. The Congratulations screen opens.

Network Setup

Set up wireless network

Use wired Ethernet instead Skip this step, I don’t have a network

You are about to set up this TV to use your home network.

If you have a wired network, please plug an Ethernet cable into the TV.

If you have a wireless network, DO NOT plug an Ethernet cable into the TV.

Set Up Channels

Antenna

Cable Skip this step, don’t scan for channels

Your TV works with either cable or antenna channels. Select the TV signal you have connected to this TV. The TV will then begin scanning for channels, which may take up to 30 minutes. Note: If you have cable, only scan for channels if you do NOT use a cable box. If you have a cable box (or satellite box), that box already has information about your channels, and you can skip this step.

Update In Progress

Please wait...

Preparing Connecting Getting info Disconnecting Loading info

(Done) (Done) (Done) (Done) (38% complete)

Date and Time Setup

Use this date and time

Set date and time manually

The current date and time are:

12/12/2010 at 10:00 PM Eastern Standard Time

If the date and time are not correct, you may manually set them.

www.insigniaproducts.com

NS-32E859A11/NS-42E859A11 Getting Started

9 The Congratulations screen opens. Press TiVo to enjoy your

new TV.

10 If you skipped the channel scan in Step 6 because you are

using a cable or satellite TV box, select the video input source for your TV. See “Selecting the video input source” on page 33.

Programming your universal Insignia remote control

Programming the mode buttons

In R3 comments, Dana said to add “DVR” in the following paragraph. Vendor says to remove it. Please advise.

You can program the mode buttons on your TV remote control (DVD, STB,

DVR, or AUX) to control the corresponding device

using your TV remote control.

To program the mode buttons:

1 Press TiVo. The Home screen opens. Press ! or " to select

Settings, then press

$ or SELECT.

2 Press ! or " to highlight Settings, then press $ or SELECT.

Congratulations!

Press TIVO to continue

You TV is now set up.

Press TIVO at any time to access the TV’s menu and On Demand shows. Press LIVE at any time to watch television.

Enjoy your new TV!

Note

To use the on-screen setup for your remote control, the remote control must be in RF mode. For more information, see “Setting up your Z-Wave remote control” on page 102.

10:00pm

Home

Settings Connect to the Internet

Settings Parental Controls Check for updates Account & system info Help Sleep timer

www.insigniaproducts.com

Getting Started NS-32E859A11/NS-42E859A11

3 Press ! or " to highlight Devices, then press $ or SELECT.

4 Press ! or " to highlight Remote control setup, then press

$ or SELECT.

5 Press ! or " to highlight the mode button on your remote

control that you want to program (DVD, STB,

DVR, or AUX),

then press

$ or SELECT. In R3 comments, Dana said to add

DVR. Vendor says to delet it. Please advise.

6 Press ! or " to highlight the device you want to control

with the button you are programming, then press

$ or

SELECT and follow the on-screen instructions.

10:00 PM

Settings

Audio Channels & providers

Network Recommendations Video

Appearance

Input sensor Remote control setup TV power On Reset device settings

INlink HDMI control

Devices

10:00 PM

Settings

Audio Channels & providers Devices Network Recommendations Video

Appearance

INlink HDMI control

evice

Set up the remote control to control the devices that you use with this TV, like your cable box, DVR, or DVD player.

Input sensor Remote control setup TV power on Reset device settings

10:00 PM

Remote Control Setup

DVD button

STB button

AUX button

Power button

Volume button Backlight

Reset all remote settings

Set up the DVD button on your remote to control your device.

10:00pm

Step 1: Select Device

DVD

VCR

Select the device you would like to control when you press the DVD button on the remote controls.

Remote Control Setup (DVD button)

+ 16 hidden pages