Universal UFS50 Owner's Manual & Operating Instructions

www.universalflooringsolutions.com

UFS50

OWNER'S MANUAL &

OPERATING INSTRUCTIONS

Revision 108

Manual Part No. 167790

Caution: Read all safety and operating instructions
before using this equipment. This owners manual
MUST accompany the equipment at all times.

08.2015

INTRODUCTION

We at Universal Flooring Solutions want to congratulate you on selecting the UFS50 Floor Scraper.
We are certain that you will be pleased with your purchase. Universal Flooring Solutions takes
pride in producing the finest products in the industry.

Operated correctly, your UFS50 Floor Scraper should provide you with years of quality service. In
order to help you, we have included this manual. This owners manual contains information nec-

essary to operate and maintain your UFS50 Floor Scraper safely and correctly. Please take a few
minutes to familiarize yourself with the UFS50 Floor Scraper by reading and reviewing this manual.

Read and follow all safely, operating and maintenance instructions.
If you should have questions concerning your UFS50 Floor Scraper, please feel free to call our

friendly customer service department at: [phone].
Regards,

Universal Flooring Solutions

NOTE THIS INFORMATION FOR FUTURE USE:

MODEL NUMBER:
SERIAL NUMBER:

PURCHASE PLACE:
PURCHASE DATE:

NOTE: For your (1) one year warranty to be effective, complete the war­ranty card (including the Serial Number) and mail it in as soon as possible.

2

TABLE OF CONTENT

SAFETY Page

Safety Message/Alert Symbols, Warnings 4
Hazard Symbols 5
General, Maintenance, Saw Safety 6-7
California proposition 65 Message 8
Electrical Requirements and Grounding Instructions 9-10
Safety Label Locations 11
Blade Changing / Installation 12

OPERATION

Wheel Adjustment 13
Handle Adjustment 14
Transportation 14
Blade Usage 15

TYPE OF TEAROUTS

Removal Materials 16
Suboor Surfaces 17

MAINTENANCE

Thermal Overload Protection 18
Cleaning 18
Repairs 19
Troubleshooting 19

GENERAL PRODUCT INFORMATION

Part List
Accessories

22-23

24

ORDERING AND RETURNING INSTRUCTIONS

Ordering Information 26
Return Material Policy 26
Packaging Instructions 26
Authorized Service Centers 26

CONT ACT AND WARRANTY

Contract 27
Warranty 27

3

UFS50 FLOOR SCRAPER

Safety precautions should be followed at all times when operating this equipment. Failure to read and
understand the Safety Precaution and Operating Instructions could result in injury to yourself and others.

Before using this machine, ensure that the person operating the machine has read and understands all
instructions in this manual.

SAFETY MESSAGE / ALERT SYMBOLS

A safety message alerts you to potential hazards that could hurt you or others. Each safety message is
preceded by a safety alert symbol ( ) and one of three words: DANGER, WARNING, or CAUTION.

SAFETY

DANGER

You WILL be KILLED or SERIOUSLY INJURED if you do not follow directions.

WARNING

You CAN be KILLED or SERIOUSLY INJURED if you do not follow directions.

CAUTION

You CAN be INJURED if you do not follow directions. It may also be used to alert against unsafe prac­tices.

Each message tells you what the hazard is, what can happen, and what you can do to avoid or re­duce injury. Other important messages are preceded by the word NOTICE.

NOTICE

You can cause PROPERTY DAMAGE to your machine if you don’t follow directions.
The safety labels should be periodically inspected and cleaned by the user to maintain good legibility

at a safe viewing distance. If the label is worn, damaged or illegible, it should be replaced.

4

UFS50 FLOOR SCRAPER

SAFETY PRECAUTIONS

ALWAYS read this Owner’s Manual before operating the machine.

ALWAYS avoid inhalation of and skin contact with silica dust and/or mist.

ON / OFF

ALWAYS place the power ON/OFF switch in the OFF position when the machine is not in
use.

ALWAYS wear approved eye protection.

SAFETY

ALWAYS wear approved respiratory protection.

NEVER operate equipment with covers, or guards removed. Keep ngers, hands, hair

and clothing away from all moving parts to prevent injury.

ALWAYS use caution around gears. Keep ngers, hands, hair and clothing away from

all moving parts to prevent injury.

NEVER touch the power cord with wet hands or while standing in water when it is con­nected to a power source.

NEVER operate the machine in an explosive atmosphere or near combustible materials.

5

UFS50 FLOOR SCRAPER

SAFETY

RULES FOR SAFE OPERATION

DANGER

Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is

to be operated by trained and qualied personnel only! This equipment is for industrial use only.

The following safety guidelines should always be used.

GENERAL SAFETY

• DONOT operate or service this equipment before reading this entire manual.

• This equipment should not be operated by persons under 18 years of age.

• NEVER operate this equipment without proper protective clothing, shatterproof glasses, steeltoed

boots and other protective devices required by the job.

• NEVER operate this equipment when not feeling well due to fatigue, illness or taking medicine.

• NEVER operate this equipment under the inuence of drugs or alcohol.

• Whenever necessary, replace nameplate, operation and safety decals when they become difcult

to read.

• ALWAYS check the machine for loose bolts before starting.

• ALWAYS wear proper respiratory (mask) hearing and eye protection

equipment when operating this machine.

• ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean,
dry location out of the reach of children.

ON / OFF

• NEVER leave the machine unattended. Turn off electric motor when unattended.

• CAUTION must be observed while servicing the machine. Rotating parts can cause injury if contacted.

• Ensure that any electrical extension cord is protected against damage. Always ensure that the

electrical extension cord is not trapped underneath the machine. When using an extension cord,
be sure to use one heavy enough to carry the current your product will draw. An undersized cord
will cause a drop in line voltage that will result in a loss of power and overheating. The Table shown
on page 10 shows the correct AWG size to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heaviest gage. The smaller the gage number, the heavier the cord.

• DONOT allow extension cord to come into contact with water or uids.

• DO NOT spray water onto electric motor .

• NEVER operate the machine in an explosive atmosphere.

• Before starting the machine, check that all guards are in position and correctly tted.

• Keep area around the machine clear of obstructions which could cause persons to fall onto moving parts.

• ALWAYS ensure that the machine is on level ground before using.

• DONOT overreach. Keep proper footing and balance at all times.

6

UFS50 FLOOR SCRAPER

SAFETY

• NEVER stand on the tool. Serious injury could occur if a power tool is tipped, or if a cutting tool is

unintentionally contacted.

• Become familiar with the controls of the machine before operating. Know how to stop the machine

quickly in case of emergency.

• ALWAYS secure work. Clamps or a vise should be used to hold work whenever practical. Keep-

ing your hands free to operate a power tool is safer.

• ALWAYS

disconnect AC power plug from power source before moving, cleaning or servicing the

machine.

• NEVER leave a tool running unattended. Do not leave a tool until it comes to a complete stop.

• Make sure the OFF/ON power switch on the electric motor is always in the OFF position before

inserting the machine’s power plug into an AC receptacle.

• Operate electric motor only at the specified voltage indicated on the nameplate.

• NEVER disconnect any “emergency or safety devices”. These devices are intended for operator

safety. Disconnection of these devices can cause severe injury, bodily harm or even death! Dis­connection of any of these devices will void all warranties.

• Unauthorized equipment modifications will void all warranties. Manufacturer does not assume respon-

sibility for any accident due to equipment modifications.

• NEVER use accessories or attachments, which are not recommended by Universal Flooring

Solutions for this equipment. Damage to the equipment and/or injury to user may result.

• Replace damaged cutting blade before operating.

• NEVER try to stop a moving blade with your hand.

MAINTENANCE SAFETY

• NEVER lubricate components or attempt service on a running machine.

• Keep the machinery in proper running condition.

• Before using a power tool, check for damaged parts. A guard or any other part that is damage

should be carefully checked to determine if it would operate properly and perform its intended
function. Always check moving parts for proper alignment or binding. Check for broken parts and
mountings and all other conditions that may affect the operation of the power tool. A guard, or any
damaged part, should be properly repaired or replaced.

7

UFS50 FLOOR SCRAPER

SAFETY WARNINGS

SILICA DUST WARNING

Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition
may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz,
brick clay,
granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne
crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition, Califor­nia and some other authorities have listed respirable crystalline silica as a substance known to cause
cancer. When cutting such materials, always follow respiratory precautions.

CALIFORNIA PROPOSITION 65 MESSAGE

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities con­tain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:

• Lead, from lead-based paints

• Crystalline silica, from bricks and cement and other masonry products

• Arsenic and chromium, from chemically treated lumber

SAFETY

For further information, consult the following sources:

http://www.osha.gov/dsg/topics/silicacrystalline/index.html
http://www.cdc.gov/niosh/docs/96-112/
http://oehha.ca.gov/prop65/law/P65law72003.html
http://www.dir.ca.gov/Title8/sub4.html

Your risk from these exposures varies depending on how often you do this type of work. To reduce
your exposure to these chemicals, work in a well-ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to lter out microscopic particles.

Asbestos Warning

Some oor coverings contain asbestos. Removing, cutting, grinding or otherwise disturbing these
coverings can cause asbestos dust to become airborne. Never remove ooring containing asbestos

without fully understanding proper state and federal procedures and guidelines for removal of these
products. Laws are different from state to state.

WARNING

To reduce the risk of electrocution, keep all connections dry and off the ground.
A Ground Fault Circuit Interrupter (GFCI) should be provided on the circuit(s) or outlet(s) to be used
for this machine. Receptacles are available having built-in GFCI protections and may be used for this
measure of safety. When using an extension cord, the GFCI should be installed closest to the power
source, followed by the extension cord and lastly, the machine.

WARNING

To reduce the risk of injury, electric shock and damage to the tool, never im-

merse your tool in liquid or allow a liquid to ow inside the tool.

8

UFS50 FLOOR SCRAPER

SAFETY

ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS

In order to prevent potential electrical shock and injury, the following electrical safety precautions and
symbols should be followed at all times!

WARNING

In case of a malfunction or breakdown, grounding provides a path of least resistance for electric cur­rent to reduce the risk of electric shock. This tool is equipped with an electric cord having an equip­ment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet
that is properly installed and grounded in accordance with all local codes and ordinances.

• Do not modify the plug provided – if it will not t the outlet; have the proper outlet installed by a

qualied electrician.

• Improper connections of the equipment-grounding conductor can result in a risk of electric

shock. The equipment-grounding conductor is the insulated conductor that has an outer surface
that is green, with or without yellow stripes. If repair or replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding conductor to a live terminal.

• Check with a qualied electrician or service personnel if the grounding instructions are not

completely understood, or if in doubt as to whether the tool is properly grounded.

• Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that

accept the tool’s plug.

• Repair or replace a damaged or worn cord immediately.

WARNING

This tool is intended for use on a circuit that has an outlet that looks like the one shown in Sketch A of
Figure 1. The tool has a grounding plug that looks like the plug illustrated in Sketch A of Figure 1. A
temporary adapter, which looks like the adapter illustrated in sketches B and C, may be used to con­nect this plug to a 2-pole receptacle as shown in Sketch B, if a properly grounded outlet is not avail­able. The temporary adapter should be used only until a properly grounded outlet can be installed by

a qualied electrician. The green-colored rigid ear, lug, and the like, extending from the adapter, must

be connected to a permanent ground such as a properly grounded outlet box.

NOTE: Use of a temporary adapter is not permitted in Canada.

Metal Screw

Grounding

Pin

(A)

ADAPTER

Grounding

Means

(C)

Cover of

Grounded

Outlet Box

Grounding

Pin

(B)

(D)

Fig. 1 Circuit and Adapter Information

9

UFS50 FLOOR SCRAPER

ON

(

(

)

)

ON

(

(

)

)

WARNING

Use only extension cords that are intended for outdoor use. These extension cords are

identied by a marking "Acceptable for use with outdoor appliances; store indoors while not
in use." Use only extension cords having an electrical rating not less than the rating of the

product. DO NOT use damaged extension cords. Examine extension cords before using and
replace if damaged. DO NOT abuse extension cords and DO NOT yank on any cord to dis­connect. Keep cords away from heat and sharp edges. Always disconnect the extension cord
from the receptacle before disconnecting the product from the extension cord.

WARNING

To reduce the risk of electrocution, keep all connections dry and off the ground. DO NOT
touch the plug with wet hands.

WARNING

SAFETY

of undersized extension cords result in low voltage to the motor that can result in motor burnout

Use
and

premature failure. Universal Flooring Solutions warns that equipment returned to us showing

signs of being run in a low voltage condition, through the use of undersized extension cords,will be
repaired or replaced totally at the customer’s expense. There will be no warranty claim.

To choose the proper extension cord,

• Locate the length of extension cord needed in the table below.

• Once the proper length is found, move down the column to obtain the correct

AWG size required for that length of extension cord.

MOTOR SPECS EXTENSION CORD LENGTH

Motor Voltage Amps 25' 50' 100' 200’

115V 1 Ph 12.8 14 ga 12 ga 8 ga 6 ga

06-550-10

208/230V 1 Ph 6.4 18 ga 16 ga 14 ga 10 ga

10

UFS50 FLOOR SCRAPER

SAFETY

SAFETY LABEL LOCATIONS

Safety labels contain important safety information. Please read the information contained on each
safety label. These labels are considered a permanent part of your saw. If a label comes off or
becomes hard to read, contact Universal Flooring

WARNING

!

•Thisequipmentmayproducedustormistscontaining
crystallinesilica.

A

•Silicaisabasiccomponentofmasonry,concrete,and
othermaterials.

•Repeatedand/orsubstantialinhalationcancause
seriousorfatalrespiratorydiseasesincludingsilicosis.

•RespirablecrystallinesilicaislistedbyCaliforniaand
otherauthoritiesasasubstanceknowntocausecancer.

•Employdustcontrolsandprotectionper
OSHA/NIOSH/MSHA.

Part # 164202

B

C

Solutions or your dealer for a replacement.

NOTICE

WARNING

!

DO NOT operate
this equipment
before reading the
owner’s manual.

Part # 154398

CAUTION

!

Flying debris and
loud noise hazards.
Wear ear and eye
protection.

Part # 171301

D

E

!

Most motor problems are caused by
low voltage from improper extension

cords. See owner’s manual for

extension cord selection.

Part # 155672

FOR INFORMATION ON

SERVICE OR
WARRANTY

PLEASE CALL

1-800-474-5594

Part # 155038

F

Part # 170480

Label C

Label A

Label D

Label B

Label E

Decal/Label Location Description

A Motor - Side Warning - Silica Warning
B Switch Box Read Manual
C Nose Weight-Top Wear Protection Equipment
D Motor - Back Notice - Extension Cord
E Motor - Side Service/ Warranty
F Switch Box QR Code for Manual

Label F

11

UFS50 FLOOR SCRAPER

BLADE CHANGING / INSTALLATION

BLADE INSTALLATION

CAUTION

Blades are sharp. Handle with care. Failure to do so could cause bodily injury.

• Dull blades greatly reduce cutting ability. Re-sharpen or replace as needed.

• Proper blade size and placement per job type greatly affects performance.

• Disconnect electrical power rst.

• Do not lean machine back onto handle.

• Always wear gloves when changing blades to protect ngers and hands.

(A)

Place a block under the

front of the machine, rais-

Loosen the two blade

(B)

cover bolts

(C)

Replace blade and tighten

bolts

ing the blade holder

1. Place a block under the front of the machine, raising the blade holder as shown in Figure A.

2. Loosen the two blade cover bolts as shown in Figure B. It is not necessary to remove the bolts.

3. Place the blade into the cutting head, sliding the blade all the way back to the bolts as shown in
Figure C. If the blade is wider than the cutting head, center the blade to the head. If the blade

is smaller than the cutting head, for the rst pass the blade should be mounted in center of the
cutting head. After the rst pass is made, blade can be offset in head to allow wheels to keep
even contact with the oor and allow easy access to the wall. Blades of longer width can be

mounted in either holes or slots or put in front of blade cover bolts.

4. Securely tighten bolts.

12

UFS50 FLOOR SCRAPER

GENERAL OPERATION

WARNING

Do not operate machine around excessive moisture areas, such as abatement work and ooded pool

areas without GFCI wall plug. Failure to do so could cause damage in machine or injury to operator.

Before using the machine, check for any broken, worn or damage parts and replace them immediately.

WHEEL ADJUSTMENT

Adjusting the wheel angle will change the blade angle to the oor. Adjustments may be required for

your particular application. Experiment with the angle to see what works the best.

NOTE:

Adjustment by trial at the beginning of a job will allow optimum performance. See Blade
Usage page 15.

(A)

A steep wheel angle is

recommended on hard

removals such as vinyl, VCT

and carpet over concrete or

wood

(B)

A low wheel angle is recom-

mended for hardwood

removal over all oors

(C)

Lay Floor Scraper back on

handles

(D)

Rotate the angle adjust-

ment wheel to the desired

blade angle

13

UFS50 FLOOR SCRAPER

GENERAL OPERATION

HANDLE ADJUSTMENT
AFTER THE PROPER WHEEL ADJUSTMENT IS ACHIEVED, ADJUST THE HANDLE LENGTH

Simply loosen the thumbscrews located on the frame and the handle will slide up and down. Locate
the most comfortable height and tighten the thumbscrews to lock the handle in place.

(A)

The handle should be adjusted to

the "belt-line" of the operator or to

an otherwise comfortable position

TRANSPORTATION

Always remove the counterweight and blades before loading or unloading.
Machine breaks down for easy transportation. Handle and/or wheel angle can by lowered to reduce
overall height.

WARNING

Keep hands and feet out from underneath the machine.

(A)

A kick plate on the back of the chassis

provides additional help when moving the
machine. Simply step downward on the kick
plate and raise the front. Adjust the angle so

the weight of the head is over the wheels.

(B)

Lower handle by loosening

tri-knob. Push handle down.

(C)

Turn bolt and remove nose

weight if you need to lift the unit.

14

UFS50 FLOOR SCRAPER

BLADES

BLADE USAGE

1. Start with a narrow blade, then increase blade size to optimize cutting pass. Narrower blades

work easier than wider blades and usually clean the oor better. Wider is not always better or

faster.

2. Proper blade size and placement, depending on material and sub-oor type, greatly affects

performance.

3. Keep in mind, narrow width blades will make a cleaner oor surface.

4. For wood or wood like oors, pound down or remove any nails or metal obstruction to avoid

blade damage.

5. When working over plywood sub-oor, try to work in the direction of the wood grain.

6. A new sharp blade being used on wood or alike sub oors may work better when slightly

dulled to avoid digging or gouging.

7. When working over concrete, beware of expansion joints and sub-oor mounted receptacles.

8. Keep your work area clean and clear of debris.

9. After you have removed a portion of material, remove it out of the way. This will give the
machine maximum performance and help to keep the work area safe.

10. Dull blades greatly reduce cutting ability. Re-sharpen or replace as needed.

11. Use Sawtec

®

replacement blades.

(A)

Blades can be offset in cutting

head for easier access to toe

kicks or removal along the wall

15

UFS50 FLOOR SCRAPER

REMOVAL MATERIALS

TYPES OF TEAROUTS

WARNING

state and federal procedures and guidelines.

• Sheet vinyl, solid vinyl, rubber tile, urethane or PVC sheet roong, will need to be scored for best

removal results.

• VCT TILE: If tiles being removed still do not come up clean or machine jumps on top of tiles,
reduce blade size to a smaller blade until proper blade size is found or use a smaller portion of
the blade. Never use a blade wider than the size of the tile being removed.

• PURE VINYL RUBBER TILE: Self scoring blades can be used with some materials. A 10" blade

is recommended for this product, but determine what size blade works best. Goods will need to
be scored down to 10 to 12 inches for proper removal.

• DIRECT GLUED CARPET: Pre-scored carpet makes machine easier to control and blades stay

sharper longer. Pre-score carpet to blade width prior to stripping. Normally 12" to 14" blades are

used on direct glued carpet, secondary backed, unitary, double glued, vinyl foam, urethane foam.

Never remove ooring containing asbestos without fully understanding proper

16

UFS50 FLOOR SCRAPER

TYPES OF TEAROUTS

SUBFLOOR SURFACES

• WOOD: When working over plywood sub-ooring, try to run machine in the same direction as the

grain in the wood. Blade in most cases should be bevel down. On solid wood oors, like plank, run

in the same direction as the plank, not cross grain or cross plank. Removing the
front counter weight will help on all soft surfaces.

• CONCRETE: When working on a concrete slab, normal blade position is bevel up for best

performance, especially when cleaning adhesive. On occasion, bevel down gives better blade life.
Test each job for best performance.

• GIBCRETE AND SOFT POURED FLOORING: Usually requires blade bevel down to create a

better wearing surface, although bevel up may work if front counter weight is removed.

BEVEL DOWN
WOOD FLOORS

BEVEL UP
CONCRETE FLOORS

Normally the bevel on the blade is up for concrete; bevel down for wood or soft sub-oors. NOTE:

CAUTION

Beware of expansion joints and oor mounted receptacles or other obstacles
in the oor.

• GLUED HARD WOOD FLOORING: A 10" blade is recommended for regular adhesive, a 6" - 7"

blade for epoxy. For proper removal of hardwood ooring (parkay laminated, plank laminated,
plank solid) ooring must be scored to blade width. A ripping guide attached to the saw can be
used to eliminate chalk line marks. Open an area large enough to t machine or start from a

doorway. It is important to keep all debris cleaned up for maximum performance of machine. True

Parkay ooring scoring is not necessary. It will come up in small pieces.

WARNING

Never remove ooring containing asbestos without

fully understanding proper state and federal proce­dures and guidelines for removal of these products.
Laws are different from state to state.

(A)

Scoring is done by using a circular saw

set at a depth of 99% of the thickness of

the board, just missing the suboor sur-

face when on concrete. A chalk line for

scoring lines can be used across the

oor the width of the blade.

17

UFS50 FLOOR SCRAPER

MAINTENTANCE

THERMAL OVERLOAD PROTECTION

The Thermal Overload manual reset switch is located on the bottom of the connection box of the elec­trical motor. If an extreme internal temperature is sensed, the switch will “trip” and the motor will shut
off automatically. If this occurs, turn the motor “ON/OFF” switch to the “OFF” position and allow the
motor to cool for at least ten minutes before restarting. Push the “reset” button (using minimal force)
and resume operations.

Thermal Overload Switch

NOTICE

Interruption of motor operation caused by the thermal switch indicates the existence of improper or insuf-

cient power to your electric motor. DOUBLE CHECK YOUR POWER SOURCE!
MAINTAINING EQUIPMENT

Keep equipment in good repair by adopting a regular maintenance program. Before use, examine
the general condition of equipment. Inspect guards, switches, tool cord set and extension cord for
damage. Check for loose screws, misalignment, binding of moving parts, improper mounting, broken
parts and any other condition that may affect its safe operation. If abnormal noise or vibration occurs,
turn the tool off immediately and have the problem corrected before further use. Do not use a dam­aged tool. Tag damaged tools “DO NOT USE” until repaired. See Repairs.

• Mechanical inspection

• Cleaning (pulleys, spindles, bearings, housing, etc.)

• Electrical inspection (switch, cord, plugs, etc.)

• Testing to assure proper mechanical and electrical operation

• Check nuts on shock absorbers and bottom plate for tightness

• Check screws on bottom bearing for tightness

• Check all screws and ttings for a tight and secure t

• Keep a sharp blade in machine for optimum performance

CLEANING

Clean dust and debris from vents. Keep the Equipment handle clean, dry and free of oil or grease.
Use only mild soap and a damp cloth to clean since certain cleaning agents and solvents are harm­ful to plastics and other insulated parts. Some of these include: gasoline, turpentine, lacquer thinner,
paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia.

Never use ammable or combustible solvents around tools. Machine is pressure washable. Make

sure machine is dry before operation.

18

UFS50 FLOOR SCRAPER

MAINTENTANCE

REPAIRS

If your tool is damaged, contact Universal Flooring Solutions for a return authorization number and return
the entire tool.

• Shipments are not accepted without a return authorization number.

• COD or freight collect shipments will not be accepted.

TROUBLESHOOTING

THERE IS NO POWER

1. Inspect electrical cord.

MOTOR NOISE

1. Make sure fan guard is not bent.

RATTLING

1. Tighten loose nuts and bolts.

MACHINE IS HARD TO HANDLE

1. Remove the counterweight.

2. Change to a smaller blade.

3. Sharpen blade.

BLOWS FUSES OR CIRCUIT BREAKERS

1. Check and/or change attached power cord. Use a 12 gauge cord, 50' or less.

2. Move to a different outlet or a better circuit.

WHEEL ADJUSTMENT WON'T WORK

1. Grease threaded shaft.

19

NOTES

20

NOTES

21

UFS50 FLOOR SCRAPER

UFS-50 PN 167676

PARTS LIST

18

45

17

46

53

52

8

19

20

10

31

56

54

1

15

22

47

32

35

6

36

9

33

7

21

43

24

3

2

26

12

50

11

34

14

25

5

44

4

27

13

16

23

51

48

30

49

55

29

OPTIONAL
ACCESSORY

OPTIONAL

39

ACCESSORY

37

OPTIONAL
ACCESSORY

22

UFS50 FLOOR SCRAPER

PARTS LIST

UFS-50 PN 167676

ITEM NO. DESCRIPTION PART # QTY.

1 LEG, WHEEL 06-500-25 2
2 WHEEL, REAR 8X1.75X .625 150LB 16-500-29 2
3 AXLE WELDMENT, BS-50 06-500-30 1
4 SHOCK ABSORBR 60 NATURAL RUBBE 06-505-102 4
5 BEARING, FLANGE, 2 BOLT, SBLF-206 06-5280-6 1
6 MTR, 1HP, 1P, 60HZ, BS-50 06-550-10 1
7 ADAPTER, ECCENTRIC 06-550-101 1
8 ADJ T-BAR WELDMENT 06-550-4 1

9 PIVOT BRACKET COVER 06-550-8 2
10 BLADE WRENCH, 7/32X6 ARM 06-6280-401B 1
11 COLLAR, 1.13 ODX .625ID .5 WIDE 140012 1
12 SCREW, HEX HEAD, 1/4-20 X 5/8 150404 8
13 SCREW, 3/8-16 X 1-1/4 HEX HEAD CAP 150774 2
14 WASHER, FLAT, SAE, 3/8 150923 3
15 WASHER, 1/2 SAE FLAT 150924 6
16 WASHER, LOCK, SPLIT, 3/8 150925 6
17 NUT, 1/2-13 HEX 151282 1
18 SCREW, HEX HD, CAP, 5/16-18 X 3/4 151369 2
19 WASHER, LOCK, SPLIT, 5/16 151747 2
20 WASHER, FLAT, SAE, 5/16 151754 2
21 WASHER, FLAT, SAE, 1/4 151915 7
22 CLAMP, 1/2 CUSHION LOOP 152471 1
23 SCREW, HEX HD CAP, 3/8-16 X 1 152507 4
24 WASHER, LOCK, SPLIT, 1/4 152591 8
25 NUT, 3/8-16 HEX CENTERLOCK 153522 2
26 SCREW, 1/2-13 X 1-3/4 HEX HEAD CAP 153853 2
27 NUT, 1/2-13 NYLOK HEX 155162 2
28 MANUAL TUBE, CLEAR 155419 1
29 SCREW, 3/8-16 X 2-1/2 HEX HEAD CAP 156030 1
30 SCREW, BTN HD 3/8-16 X 3/4 SOCK 156635 2
31 KNOB, TRI PLASTIC, 1" 156770-01 2
32 TAG, SERIAL NUMBER, BLANK 157500-RW 1
33 SCREW, SET, 1/4-20X1/4 157528 1
34 LOGO, MK ADHESIVE 157914 2
35 GRIP, HANDLE 7/8 ID 158608 2
36 KEY, 3/16 SQR X 1-1/2 165347 1
37 BLADE, SCRAPER, 10" X 3" 167619 1
38
39 BLADE SCRAPER, 7-3/8" X 3" 167796 1

OWNERS MANUAL UFS50 SCRAPER

167790 1

23

UFS50 FLOOR SCRAPER

PARTS LIST

UFS-50 PN 167676

ITEM NO. DESCRIPTION PART # QTY.

40
41
42
43 SCREW, SET, #10-24 X 3/16 168055 2
44 NUT, HEX, SFL, 5/16 -18 5000810 8
45 KNOB, THRD 1/2 -13 X 1.5 CP-10098 1
46 COLLAR, 1.13 ODX .625 ID .5 WIDE CP-10099 1
47
48 BOTTOM COVER PA-10599 1
49 BLADE HOLDER PA-10606 1
50 COUNTER WEIGHT, FRONT PA-10607 1
51 CUTTING HEAD PA-10622 1
52 ASSY, PIVOT PLATE PG-10126 1
53 ADJUSTMENT SHAFT WELDMENT PG-10127 1
54 CHASSIS, BS-50 PG-10128 1
55 TOOL HOLDER WELDMENT PG-10130 1
56 HANDLE WELDMENT PG-10131 1

ASSY, WARNING LABELS, UFS50

ASSY, CARTON UFS50

PALLET, UFS50 SCRAPER

ASSY, SWITCH, 120V/60HZ, UFS50

167847 1
168043 1
168044 1

P004942 1

24

UFS50 FLOOR SCRAPER

ACCESSORIES

ITEM NUMBER DECRIPTION

ACCESSORIES

1

2

3

167619

167796

PG-10130 Tool Holder

Vinyl Scraper blade

7-3/8" x 3"

Vinyl Scraper blade

10" x 3"

25

UFS50 FLOOR SCAPER RETURN INSTRUCTIONS

RETURN MATERIALS POLICY

To expedite the service relative to the return of a product purchased through Universal Flooring
Solutions, please observe the following:

NOTE: When returning all items, they must have been pur

chased within the previous twelve (12) months.

• Have the Model Number of the saw

• Have the Serial Number of the saw

• Have the location of where the saw was purchased

• Have the date when the saw was purchased

• Contact Customer Service for approval to return the item(s)

• Obtain a Returned Goods Number (RGA) authorizing the return

• Follow the packaging instructions in the following section

• Ensure your item(s) are prepaid to the destination

PACKAGING INSTRUCTIONS

• Dry the Floor Scraper before shipping

• When

packing, include the following: UFS50 Floor Scraper, nose weight and handle.

• Package the unit in its original container or one of comparable size (do not ship the unit partially

exposed)

• Ensure all parts are secured in the packaging to prevent moving

AUTHORIZED SERVICE CENTERS

For quicker repair time, you may contact Universal Flooring Solutions Customer Service, on
[phone] for the Authorized Service Center closest too you or visit our web site at

intafloors.com.au. For technical questions, call [phone]

www.

26

UFS50 FLOOR SCAPER

CONTRACT AND LIMITED WARRANTY

CONTACT:

Please contact Intafloors Trade Depot Customer Service Department with any questions you
might have regarding distributors, parts or service.

Telephone: [phone]
Fax: [phone]
E-mail: [e-mail]
Customer Service Hours: Monday through Friday, 6:30am - 4:30pm GMT+10

Intafloors Trade Depot Head Office
15 Artisan Road
Seven Hills NSW 2147

Universal Flooring Solutions, INC. LIMITED WARRANTY

Universal Flooring Solutions, INC. will guarantee every machine they build, to be free from defects in
material and workmanship for (1) one year from date of purchase. The obligation of Universal
Flooring Solutions, INC. under this warranty is limited to the repair or replacement of any parts which,
under normal use, prove to be defective in material or workmanship. The parts involved or the unit in
question should be returned to Universal Flooring Solutions, INC. or to a point designated by us,
transportation prepaid.

This warranty does not obligate us to bear the cost of labor or transportation charges in connection
with replacement or repair of defective parts. Likewise, it shall NOT apply to any unit which has been
subjected to misuse, neglect or accident. This warranty does NOT apply to any machine which has
been repaired or altered outside our factory.

This warranty does NOT obligate Universal Flooring Solutions, INC., with respect to items not of our
manufacture, such as engines, motors, hydraulics, etc., which are subject to their own guarantees and
warranties.

We shall in no event be liable for consequential damages or contingent liabilities arising out of failure
of any equipment or parts to operate properly.

© COPYRIGHT 2015, Universal Flooring Solutions, INC. ALL

RIGHTS RESERVED.

The Universal Flooring Solutions logo is a registered trademark of Universal Flooring Solutions, Inc.
and may not be used, reproduced, or altered without written permission. All other trademarks are the
property of their re-spective owners and used with permission.

Universal Flooring Solutions may have patents, patent applications, trade marks, copyrights of other
intellectual property right covering this product in this document.

This manual MUST accompany the equipment at all times. This manual is considered a permanent
part of the equipment and should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for

printing.

27

UFS50 FLOOR SCRAPER

OWNER'S MANUAL & OPERATING INSTRUCTIONS

Intafloors Trade Depot

15 Artisan Road

Seven Hills NSW 2147

Phone: [phone]

Fax: [phone]

www.intafloors.com.au