OWNERS MANUAL
INFRARED CONSTRUCTION HEA TERS
SPC-15R/15R SPC-30R/30R
STOP
Models
QUESTIONS?
MISSING / DAMAGED PARTS
Please do not return this product to the store.
If a part is damaged or missing, simply e-mail us at
php@allpro-heaters.com, or visit our website at
http://allpro-heaters.com, or call our Customer
Service Department at (888) 619-7060.
We will be happy to assist you!
Y ou can register your heater on line at
http://allpro-heaters.com/warranty .
TABLE OF CONTENTS
WARNINGS .................................................................................................................................. 2
HEATER SPECIFICATIONS................................................................................................................ 2
SAFETY PRECAUTIONS.................................................................................................................... 3
OPERATING PRECAUTIONS............................................................................................................. 3
ODOR FADE WARNING...................................................................................................................... 4
ASSEMBLY INSTRUCTIONS ............................................................................................................. 5
OPERATING INSTRUCTIONS ............................................................................................................ 7
SERVICING ......................................................................................................................................... 8
PARTS BREAKDOWN ........................................................................................................................ 9
WARRANTY....................................................................................................................................... 10
SERVICE CENTERS ........................................................................................................................ 10
WARRANTY REGISTRATION............................................................................................................11
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
© 2002 Scheu Products Company
Models
SPC-15R/15R SPC-30R/30R
HEATER SPECIFICATIONS
Type of Gas: For use with Propane Only
Gas Supply Pressure
to regulator: Maximum: Bottle Pressure Minimum: 20 psi (1.37 bar)
Regulator out: 10 - 18 psi (.68 bar - 1.2 bar)
Minimum Ambient Temp. Rating 0°F (-17.8°C)
Model: SPC-15R / 15R SPC-30R/ 30R
Rating: 10,000 - 15,000 Btu/hr 20,000 - 30,000 Btu/hr
Ignition: Match Light Piezo Ignition
Fuel Consumption: .5 - .7 #/hr .5 - 1.3 #hr
(3.0 - 4.4 kW) (5.8 - 8.8 kW)
(.23 - .32 kg/hr) (.23 - .59 kg/hr)
W ARNINGS
YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS, SO PLEASE
READ THESE INSTRUCTIONS BEFORE YOU OPERATE THIS HEATER.
GENERAL HAZARD WARNING:
FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN RESULT IN
DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE FROM HAZARDS OF FIRE, EXPLOSION, BURN,
ASPHYXIATION, CARBON MONOXIDE POISONING, AND/OR ELECTRICAL SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC. CONTACT
THE MANUFACTURER.
WARNING: NOT FOR HOME OR RECREATIONAL VEHICLE USE
WARNING: FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID COMBUSTIBLES, SUCH AS
BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS RECOMMENDED
BY THE INSTRUCTIONS NEVER USE THE HEATER IN SPACES WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE
COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES OR UNKNOWN
CHEMICALS.
Scheu Products Company, Incorporated
Mail: P.O. Box 250, Upland, CA 91785
Plant: 8855 Baker Ave., Rancho Cucamonga, CA 91730
Telephone: 800-325-7057
www.scheuco.com
customerservice@scheuco.com
8506
September 2002
Page -2-
Models
SPC-15R/15R SPC-30R/30R
OPERATING PRECAUTIONS
This is a propane, direct-fired, infrared heater. It's intended use
is primarily temporary heating of buildings under construction,
alteration or repair.
Propane is heavier than air. If propane leaks from a connection
or fitting, it sinks to the floor, collecting there with the
surrounding air, forming a potentially explosive mixture.
Obviously, propane leaks should be avoided, so set up the
propane supply with utmost care. Read enclosed Odor Fade
and Propane Sheet for additional information about detecting
propane leaks. Leak check new connections or reconnections
with a soap and water solution and follow all connection
instructions herein. Also, ask your propane dealer for advice on
the propane application and supply installation and ask him to
check it if there are any questions.
Check with your local fire safety authority if you have any
questions about your applications. Standards govern the use of
fuel gases and heat producting products in specific
applications. Your local authority can advise you about these.
Direct-Fired means that all of the combustion products enter the
heated space. Even though this heater operates very close to
100 percent combustion efficiency, it still produces small
amounts of carbon monoxide. Carbon monoxide (called CO) is
toxic. We can tolerate small amounts but not a lot. CO can build
up in a heated space and failure to provide adequate ventilation
could result in death. The symptoms of inadequate ventilation
are:
headache dizziness
burning eyes and nose nausea
dry mouth or sore throat
So, be sure to follow advice about ventilation in these operating
instructions.
When the heater is to be operated in the presence of other
people the user is responsible for properly acquainting those
present with the safety precautions and instructions, and of
the hazards involved.
SAFETY PRECAUTIONS
1. Keep children and animals away from heater.
2. Never operate heater while sleeping or unattended.
3. Check the heater thoroughly for damage. DO NOT operate
a damaged heater.
4.DO NOT modify the heater or operate a heater which has
been modified from its original condition.
5. Use only propane gas.
6.Use only VAPOR WITHDRAWAL propane supply. If there is
any question about vapor withdrawal, ask your propane
dealer.
7.For outdoor use only. AREA MUST BE WELL VENTILATED.
Provide minimum openings of 1 sq ft (.093m²) near the
floor and 1 sq ft. (.093²) near the ceiling. Do not use inside
house, camper, tent and vehicle. Or any type of unvented or
enclosed area.
8. Do not use heater in basement or below ground level.
9. Before connecting heater to the propane tank, make sure
the heater regulator knob is in the "OFF" position. Always
connect and light heater in areas free of open flames.
10. Mount the propane cylinders vertically (shutoff valve up).
Secure them from falling or being knocked over and protect
them from damage.
11.IMPORTANT Use only the hose and regulator assembly
provided with the model SPC-30R / 30R. Inspect the hose
assembly before each use of the SPC-30R/30R. If there is
excessive abrasion or wear, or hose is cut, replace with
hose assembly listed on parts list before using heater. The
hose and regulator must be protected from damage.
12. The heater burner must be at least 2 ft. (.61m) above the
floor. Always attach to propane tank in an upright position.
Never operate a heater on its side or attach to propane tank
in a horizontal position. This could lead to dangerous flareups or fire. Do not direct heat toward propane cylinders.
13. Maintain minimum clearance from normal cumbustible
materials (like paper) as follows: Sides - 3 ft. (.91m); Top &
Front - 5 ft. (1.5m). Locate 10 ft. (3m) from canvas or plastic
tarpaulins or similar coverings and secure them to prevent
flapping or movement due to wind action.
14.If at any time gas odor is detected, IMMEDIATELY
DISCONTINUE operation until the source of gas has been
located and corrected. Read enclosed Odor fade and
Propane Sheet for additional information about detecting
propane leaks.
15.Install the heater such that is is not directly exposed to water
spray, rain, dripping water and/or wind.
16. Operate only on a stable, level surface.
17. Due to the high surface and exhaust temperatures, adults
and children must observe clearances to avoid burns or
clothing ignition.
18. Since permanent skin tissue damage can occur, do not
move, handle or service while hot or burning. Do not attach
or remove a hot or operating heater from the propane tank.
19.Before each use, check heater for leaks. Never use an
open flame to check for leaks. Apply a mixture of liquid
soap and water to all joints. Bubbles forming show a leak.
Correct all leaks.
20.Keep all connections and fittings clean. Make sure propane
tank valve is clean. Check "O" ring on heater inlet fuel valve
connector for damage before each use. Replace if worn or
damaged.
21. Use only in accordance with local codes or, in the absence
of local codes, with the Standard for the Storage and
Handling of Liquefied Petroleum Gases ANSI/NFPA 58 and
CSA B149.1, Natural Gas and Propane Installation Code.
Page -3-
Models
SPC-15R/15R SPC-30R/30R
ODOR FADE WARNING
WARNING
Asphyxiation Hazard
• Do not use this heater for heating human living quarters.
• Do not use in unventilated areas.
• The flow of combustion and ventilation air must not be
obstructed.
• Proper ventilation air must be provided to support the
combustion air requirements of the heater being used.
• Refer to the specification section of the heater’s manual,
FUEL GAS ODOR
LP gas and natural gas have man-made odorants added specifically for detection of fuel gas leaks.
If a gas leak occurs you should be able to smell the fuel gas. Since Propane (LP) is heavier than air you should smell for the gas
odor low to the floor.
• Do not take any action that could ignite the fuel gas. Do not
operate any electrical switches. Do not pull any power
supply or extension cords. Do not light matches or any other
source of flame. Do not use your telephone.
• Get everyone out of the building and away from the area
immediately.
• Close all propane (LP) gas tank or cylinder fuel supply
valves, or the main fuel supply valve located at the meter if
you use natural gas.
• Propane (LP) gas is heavier than air and may settle in low
ANY GAS ODOR IS YOUR SIGNAL TO GO INTO IMMEDIATE ACTION!
heater dataplate, or contact the Scheu Products Company to
determine combustion air ventilation requirements of the
heater.
• Lack of proper ventilation air will lead to improper
combustion.
• Improper combustion can lead to carbon monoxide
poisoning leading to serious injury or death. Symptom of
carbon monoxide poisoning can include headaches
dizziness and difficulty in breathing.
areas. When you have reason to suspect a propane leak,
keep out of all low areas.
• Use your neighbor’s phone and call your fuel gas supplier
and your fire department. Do not re-enter the building or
area.
• Stay out of the building and away from the area until
declared safe by the firefighters and your fuel gas supplier.
• FINALLY, let the fuel gas service person and the firefighters
check for escaped gas. Have them air out the building and
area before you return. Properly trained service people must
repair any leaks, check for further leakages, and then relight
the appliance for you.
ODOR FADING - NO ODOR DETECTED
• Some people cannot smell well. Some people cannot smell
the odor of the man-made chemical added to propane (LP)
or natural gas. You must determine if you can smell the
odorant in these fuel gases.
• Learn to recognize the odor of propane (LP) gas and natural
gas. Local propane (LP) gas dealers will be more than
happy to give you a scratch and sniff pamphlet. Use it to
become familiar with the fuel gas odor.
• Smoking can decrease your ability to smell. Being around
an odor for a period of time can affect your sensitivity to that
particular odor. Odors present in animal confinement
buildings can mask fuel gas odor.
ATTENTION - CRITICAL POINTS TO REMEMBER!
• Propane (LP) gas has a distinctive odor. Learn to recognize
these odors. (Reference Fuel Gas Odor and Odor Fading
sections above.
• Even If you are not property trained in the service and repair
of the heater, ALWAYS be consciously aware of the odors of
propane (LP) gas and natural gas.
• If you have not been properly trained in repair and service of
propane (LP) gas then do not attempt to light heater,
perform service or repairs, or make any adjustments to the
heater on the propane (LP) gas fuel system.
• The odorant in propane (LP) gas and natural gas is
colorless and the intensity of its odor can fade under
some circumstances.
• If there is an underground leak, the movement of gas
through the soil can filter the odorant.
• Propane (LP) gas odor may differ in intensity at different
levels. Since Propane (LP) gas is heavier than air, there
may be more odor at lower levels.
• Always be sensitive to the slightest gas odor. If you
continue to detect any gas odor, no matter how small, treat it
as a serious leak. Immediately go into action as discussed
previously.
• A periodic sniff test around the heater or at the heater’s
joints; i.e. hose, connections, etc., is a good safety practice
under any conditions. If you smell even a small amount of
gas, CONTACT YOUR FUEL GAS SUPPLIER IMMEDIATELY.
DO NOT WAIT!
Page -4-
Models
SPC-15R/15R SPC-30R/30R
MODELS
SPC-30R 30R
ASSEMBLY INSTRUCTIONS
1. Inspect the heater components for possible shipping damage. If any is found, immediately notify the dealer.
2. Follow the following instructions to assemble the SPC-30R /30R:
Check to make sure that all of the following packaged
components (see Figure 1) are incuded.
Burner Assembly w/ regulator 1
Burner Assembly w/o regulator 1
1.
Heater Support 1
Tank Plate 1
Wing Nuts 2
Burner Clamp 2
Burner Mtg. Screw 2
Piezo Ignitor 1
Piezo Mtg. Nut 1
2.
Figure 1
Insert the piezo ingitor into the bracket on the burner
support as shown in Figure 2. Then tighten the piezomounting nut. Care should be taken not to over
tighten the nut.
Figure 2
Page -5-
3.
Models
SPC-15R/15R SPC-30R/30R
MODELS
SPC-30R 30R
ASSEMBLY INSTRUCTIONS
Connect the burner hoses together as shown in
Figure 3 & 4. Wrench tighten to insure leak tight
connection.
4.
Figure 3
Figure 4
Mount the burner onto the support using the burner
clamps and screws as shown in Figure 5. Care
must be taken to insure that the air holes on the
sides of the burner tube are not blocked. Securely
tighten the burners into place.
Figure 5
Page -6-
Models
SPC-15R/15R SPC-30R/30R
MODELS
SPC-30R 30R
ASSEMBLY INSTRUCTIONS
5.
Figure 6
Figure 7
OPERATING INSTRUCTIONS
MODELS SPC-15R/15R SPC-30R/30R
PREPARING FOR OPERATION
1. Check the heater for possible shipping damage. If any is
found, immediately notifiy the factory.
2.Follow all of the Safety and Operating Precautions.
3.Refer to the exploded view for general assembly layout.
4.Check the "O" ring on the POL before each use. Replace the
"O" ring if there is any sign of wear or damage.
5.Make sure heater regulator knob is on the "OFF" position.
6.(A) Attach the heater (30R only) to the guard on the propane
cylinder with the body of the stand on the inside of the guard
and the bolts through two holes in the guard (see Figure 1).
Tighten the latching plate into place using the wing nuts
provided (see Figure 2).
6.(B) Connect the POL fitting at regulator (15R/30R) to the
propane cylinder by rotating the POL nut counter-clockwise into
the propane cylinder's valve outlet and securely tighten with a
wrench. WARNING: Attach heater in upright position. Never
attach heater in a horizontal position. This could lead to
dangerous flare-ups or fire.
7. Securely tighen all gas connections.
8. Open the cylinder's gas valve and check all gas connections
with a soap and water solution. DO NOT USE A FLAME.
Attach the electrode wires to the piezo Ignitor as
shown in Figures 6 & 7.
Figure 1
Figure 2
Page -7-
Models
SPC-15R/15R SPC-30R/30R
OPERATING INSTRUCTIONS
START
WARNING: When lighting the heater DO NOT look over top of
heater (reflector). Stand to the side of the heater during
ignition. Do not stand or have any part of your body in front of
the heater.
1.WARNING: MAKE SURE THERE IS NO OPEN FLAME IN THE
AREA. Fully open the valve on the propane cylinder.
2. Turn the heater regulator knob counterclockwise to the "HI"
position.
3.To light: (Read all lighting instructions before attempting to
ignite heater)
a) Repeatedly push and release the piezo electric ignitor
(SPC-30R), or place a lighted match near the face of
the heating element (mesh screen) of the burner you
are lighting, using the hole located on the side of the
reflector. CAUTION: DO NOT LIGHT AT THE ORIFICE.
b) Depress the red button on the safety valve admitting
gas to the burner. WARNING: DO NOT DEPRESS RED
VALVE BUTTON BEFORE REPEATEDLY ACTIVATING
THE PIEZO (SPC-30R) OR INSERTING MATCH.
c) When the gas on the face of the mesh screen lights,
continue to hold the valve button depressed for 30
seconds, then release.
4.If flame goes out, wait 5 minutes and repeat the lighting
procedure.
5.If heater will not light after repeated tries, do not attempt to
repair heater. Return heater to nearest authorized service
center or to manufacturer of this product, freight prepaid.
6. (SPC-30R) Repeat steps 1 through 4 to ignite the other
burner.
7. After both burners (SPC-30R) or single burner (SPC-15R),
are lit, turn the heater regulator knob to the desired heat
setting (LOW, MED, HI).
STOP
1.Securely close valve on the propane cylinder.
2.Turn the heater regulator knob to the "OFF" position. Wait
15 minutes for the heater to cool down before handling
heater.
3.Always remove the heater from the propane tank after each
use. Do not store the heater while attached to propane tank.
Remove the heater from the propane tank by turning the fuel
connector nut clockwise. Always store propane tank
outdoors. Never store propane tank in an enclosed area.
RESTART AFTER SAFETY SHUTDOWN
1.Securely close valve at propane cylinder.
2. Wait 5 minutes.
3. Restart following "Start" procedure.
MAINTENANCE AND STORAGE
1. The heater should be inspected before each use, and at
least annually by a qualified person.
2.Before each use, check the soft "O" ring seat at the bullnose
of the POL fitting. If the "O" ring is cut, scuffed, or otherwise
damaged, replace it with part number 6681.
3.Turn off the gas at the LP-gas supply cylinder when the
heater is not in use.
4. When the heater is to be stored, the connection between the
LP-gas supply cylinder and the heater must be
disconnected and the cylinder removed from the heater and
stored out of doors and in accordance with Chapter 5 of the
standard for Storage and Handling of Liquefied Petroleum
Gases ANSI/NFPA 58.
SERVICING
A hazardous condition may result if a heater is used that has
been modified or is not functioning properly. When the heater is
working properly:
* The flame is contained within the heater.
* The flame is essentially blue.
* There is no strong disagreeable odor, eye burning or other
physical discomfort.
* There is no smoke or soot internal or external to the heater.
* There are no unplanned or unexplained shut downs of the
heater.
The parts lists and exploded view show the heater as it was
constructed. Do not use a heater which is different from that
shown. In this regard, use only the hose, regulator and cylinder
connection fitting (called a POL fitting) supplied with the heater.
IMPORTANT For this heater, the regulator must be set as
shown in "specifications". If there is any uncertainty about the
regulator setting, have it checked.
A heater which is not working right must be repaired, but only by
a trained, experienced service person. To find the service
center closest to you, visit our website at www.scheuco.com.or
call (888) 619-7060.
You may also obtain in-warranty or out-of-warranty service by
taking the product to your local service center.
In-warranty products will be repaired with no charge for either
parts or labor. Please include a brief statement indicating date,
place of purchase, the nature of the problem and proof of
purchase.
Out-of-warrranty products will be repaired with a charge for
parts and labor.
Page -8-
Models
1
5
7
8
9
12
4
3
2
7
11
6
13
6
2
14
10
SPC-15R/15R SPC-30R/30R
SPC-15R/15R SPC-30R/30R
PARTS BREAKDOWN
SPC-15R/15R SPC-30R/30R
5
1
3
4
2
iITEM PART NUMBER
NO. SPC15R DESCRIPTION QTY
1. 8660 BURNER HEAD ASSY 1
2. 8661 THERMOCOUPLE 1
3. 8662 NUT, THERMOCOUPLE 2
4. 8663 POL EXCESS FLOW/REGULATOR 1
5. 8664 GRILLE 1
* 8632 INSTRUCTION HANG TAG 1
* 8506 MANUAL 1
ITEM PART NUMBER DESCRIPTION QTY
NO. SPC30R
1. 8660 BURNER HEAD ASSEMBLY 2
2. 8661 THERMOCOUPLE 2
3. 8662 NUT, THERMOCOUPLE 4
4. 8663 POL EXCESS FLOW/REGULATOR 1
5. 8664 GRILLE 2
6. 8665 HOSE ASSEMBLY 2
7. 8666 ELECTRODE ASSEMBLY 2
8. 8672 PIEZO IGNITOR 1
9. 8673 NUT, PIEZO 1
10. 8667 SUPPORT ARM 1
11. 8668 BRACKET, SUPPORT ARM 1
12. 8669 FITTING 1
13. 8670 FITTING 1
14. 8671 BURNER HEAD MOUNTING BRACKET 2
* 8656 INSTRUCTION HANG TAG 1
* 8506 MANUAL 1
*NOT SHOWN
* NOT SHOWN
Page -9-
Page-9-
Models
SPC-15R/15R SPC-30R/30R
WARRANTY
We are pleased that you have selected our product and take
this opportunity to assure you that qualified service facilities are
available if required. With the cooperation of independent
dealers, a nationwide network of authorized servicing dealers is
available for your servicing requirements.
Should your product require servicing, read the section of the
manual entitled “Servicing”.
Who gets the warranty? The warranty is limited to the consumer
who originally purchases the product.
What is covered? This limited warranty covers all imperfections
in workmanship and material.
What is not covered? This limited warranty does not cover
damage resulting from accident, misuse or abuse, lack of
proper maintenance, affixing of any attachments not provided
with the products, or loss of parts. IN NO EVENT SHALL
SCHEU PRODUCTS COMPANY BE LIABLE FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES NOR FOR ANY
DAMAGES RESULTING FROM MISUSE OR MODIFICATION OF
THIS PRODUCT.
Registering this heater within 10 days of date of purchase
ensures the buyer the protection as stated on our limited
warranty form.
the like and no implied warranty arising from course of dealing
or usage of trade. This warranty will not apply to any product
which has been repaired or altered outside of the California
factory in any respect which in our judgment affects its condition
or operation.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This Warranty gives you specific
legal rights, and you may have other rights which vary from state
to state.
SERVICE CENTERS
Scheu Products Company has over 1,000 service centers
throughout North America. Call (888) 619-7060 or email
php@scheuco.com to request the service center nearest you.
Include the Make and model of your heater in any emails.
INSTRUCTIONS FOR ORDERING PARTS
We recommend that only parts supplied by the manufacturer be
used on this unit. A locally purchased part may appear to be
identical, although in reality it might endanger the heater or the
persons operating the heater.
The heater should be serviced only by a trained, experienced
service person.
LIMITED WARRANTY
The company warrants this product to be free from
imperfections in material or workmanship, under normal and
proper use in accordance with instructions of The Company, for
a period of one year from the date of delivery to the buyer. The
Company, at its option, will repair or replace (f.o.b. factory,
California) products returned by the buyer to the factory,
California, transportation prepaid within said one year period
and found by the Company to have imperfections in material or
workmanship.
If a part is damaged or missing, simply e-mail us at
php@scheuco.com, visit our website at scheuco.com, or call
our Technical Support Department at (888) 619-7060.
Address any Warranty Claims to the Customer Service
Department, Scheu Products Company, Incorporated, P.O. Box
250, Upland, California 91785, or e-mail us at
php@scheuco.com. Include your name, address and telephone
number and include details concerning the claim. Also, supply
us with the purchase date and the name and address of the
dealer from whom you purchased our product.
The foregoing is the full extent of the responsibility of the
Company. There are no other warranties, express or implied.
Specifically there is no warranty of fitness for a particular
purpose and there is no warranty of merchantability. In no event
shall the Company be liable for delay caused by imperfections,
for consequential damages, or for any charges of the expense
of any nature incurred without its written consent. The cost of
repair or replacement shall be the exclusive remedy for any
breach of warranty. There is no warranty against infringement of
Read the section on "Servicing" before ordering parts.
For parts orders, call 888-619-7060 or e-mail us at
php@scheuco.com. Please have the model number of your
heater and the replacement part number when placing your
order.
Page -10-
Hand print only. Use black or blue ink pen to fill in this form. Cross or check inside the circle.
Your Information
First Name
Mailing Address
City
E-mail Address
Annual house hold income before tax
Age of Purchaser
Your Preferences
Who selected the heater?
Heater will be used by?
How did you learn
about our heater?
Warranty Registration
WARRANTY
REGISTRATION
Last name
State
<$9,999 $10,000 to $19,999
20-29 years 30-39 years 40-49 years 50-59 years >60 years<20 years
Fold Here
Male
Individual Business
Advertising Relative/friend
Store display
Female Both
Previously owned heater
$20,000 to $34,999 $20,000 to $34,999
In choosing your heater the following categories
were:
Features
Portability
Postal code
Somewhat
Important
-
Important
>$50,000
Very
Important
Other
What prompted you to
buy your heater?
Where will you use the
heater?
Sudden cold weather Emergency ba c kup heat
Replaces old model
Heater on sale
Construction project
Construction site
Shop Patio
Other
Hard to heat location
Other
Warehouse
Product Information
/ /
Date of Purchase (MM/DD/YY)
Brand Name
Cost of Heater ($)
All Pro Universal National Riverside
Store Inform ation where heater was purchased
S/N (Located on a silver label on heater)
Price
Quality
Heat Output
Warranty
Serviceability
Fuel economy
Ease of use
Size
Fold Here
-
Model Number (Located on a black and white label on heater)
Store Name
Type of Store
Registering this heater within 10 days of purchase ensures the buyer the protection as stated on our limited warranty form.
Hardware Home Center Warehouse Retailer Discount Store Farm Supply
City
Contractor’s Supply Other
State
SCHEU PRODUCTS COMP ANY, INC
A TTN: MARKETING DEP AR TMENT
8855 BAKER A VENUE
RANCHO CUCAMONGA, CA 91730
Visit our website for product information, technical support, customer service, and warranty registration at:
WWW .ALLPRO-HEATERS.COM for All-Pro products or WWW .UNVERISAL-HEA TERS.COM for Universal products.
Loading...