Unitronics V430-J-TRA22, V130-J-TRA22, V350-35-TRA22, V350-J-TRA22, V130-33-RA22 Installation Manual















Vision™ OPLC™ Installation Guide

V130-33-RA22/V130-J-RA22
V350-35-RA22/V350-J-RA22
V430-J-RA22

V130-33-TRA22/V130-J-TRA22
V350-35-TRA22/V350-J-TRA22
V430-J-TRA22

12 Digital Inputs, including 1 HSC/Shaft-encoder Inputs,
2 Analog, 2 PT100/TC inputs

8 Relay Outputs

2 Analog Outputs

12 Digital Inputs, including 1 HSC/Shaft-encoder Inputs,
2 Analog Inputs, 2 PT100/TC inputs

4 Relay Outputs

2 Analog Outputs

4 high-speed npn Transistor Outputs

General Description

All of the controllers covered in this guide are micro-OPLCs, rugged programmable logic controllers that
comprise built-in operating panels and on-board I/Os.

Item

On-board I/O Model Dependent

Screen 2.4" 3.5" Color Touch 4.3" Color Touch

Keypad Yes None

Function Keys None Yes

Com Port, Built-in

RS232/485 Yes Yes Yes Yes Yes*

USB device,

mini-B

Com Ports, separate
order, user-installed

* V430J comprises both RS232/485 and USB ports; note that only one channel may be used at a time.

V130-R A22

V130J- RA22

None None None None Yes*

The user may install a CANbus port (V100-17-CAN), and one of the following:

• RS232/RS485 port (V100-17-RS4/V100-17-RS4X)

• Ethernet (V100-17-ET2)

• Profibus Slave (V100-17-PB1)

Standard Kit Contents

Item

Controller Yes

Terminal Blocks Yes

Battery (installed) Yes

Slides
(2 sets of key labels)

Mounting Brackets Yes (2 parts) Yes (4 parts)

Rubber Seal Yes

Programming cable
+ RS232 adapter

USB
programming cable

V130-R A22

V130J- RA22

V130-T RA22

V130J- TR A22

V130-T RA22

V130J- TR A22

None Yes None

V350-R A22

V350J- RA22

V350-R A22

V350J- RA22

Yes None

None Yes

V350-T RA22

V350J- TR A22

V350-T RA22

V350J- TR A22

V430J- RA22

V430J- TR A22

V430J- RA22

V430J- TR A22

Unitronics 1

Vision™ OPLC™ Installation Guide

Alert Symbols and General Restrictions

When any of the following symbols appear, read the associated information carefully.

Symbol Meaning Description

Danger The identified danger causes physical and property damage.

Warning The identified danger could cause physical and property damage.

Caution Caution Use caution.

 Before using this product, the user must read and understand this document.
 All examples and diagrams are intended to aid understanding, and do not guarantee operation.

Unitronics accepts no responsibility for actual use of this product based on these examples.

 Please dispose of this product according to local and national standards and regulations.
 Only qualified service personnel should open this device or carry out repairs.

 Failure to comply with appropriate safety guidelines can cause severe injury or property

damage.

 Do not attempt to use this device with parameters that exceed permissible levels.
 To avoid damaging the system, do not connect/disconnect the device when power is on.

Environmental Considerations

 Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,

moisture or rain, excessive heat, regular impact shocks or excessive vibration, in
accordance with the standards given in the product’s technical specification sheet.

 Do not place in water or let water leak onto the unit.
 Do not allow debris to fall inside the unit during installation.

 Ventilation: 10mm space required between controller’s top/bottom edges & enclosure walls.
 Install at maximum distance from high-voltage cables and power equipment.

Mounting

Note that figures are for illustrative purposes only.

Dimensions: V130/V350/V130J/V350J

* Note that for models V130J/V350J, the bezel width is 6.7 mm (0.26”).

2 Unitronics

Vision™ OPLC™

Dimensions: V430J

Panel Mounting

Before you begin, note that the mounting panel cannot be more than 5 mm thick.

UL listed models:
To meet the UL508 standard, panel-mount the device on the flat surface of a Type 1 enclosure.

1. Make a panel cut-out of the appropriate size:

 V130/V350/V130J/V350J: 92x92 mm (3.622”x3.622”).
 V430J: 122.5x91.5 mm (4.82”x3.6”).

2. Slide the controller into the cut-out, ensuring that the rubber seal is in place.

3. Push the mounting brackets into their slots on the sides of the panel as shown in the figure below.

4. Tighten the bracket’s screws against the panel. Hold the bracket securely against the unit while
tightening the screw.

5. When properly mounted, the controller is squarely situated in the panel cut-out as shown in the
accompanying figures.

V130/V350/V130J/V350J

Unitronics 3

Vision™ OPLC™ Installation Guide

V430J

DIN-rail Mounting (V130/V350/V130J/V350J)

1. Snap the controller onto the DIN rail as
shown in the figure to the right.

2. When properly mounted, the controller is
squarely situated on the DIN-rail as
shown in the figure to the right.

4 Unitronics

Vision™ OPLC™

Wiring

 Do not touch live wires.

 Install an external circuit breaker. Guard against short-circuiting in external wiring.
 Use appropriate circuit protection devices.
 Unused pins should not be connected. Ignoring this directive may damage the device.
 Double-check all wiring before turning on the power supply.

 To avoid damaging the wire, do not exceed a maximum torque of 0.5 N·m (5 kgf·cm).

Caution

 Do not use tin, solder, or any substance on stripped wire that might cause the wire

strand to break.

 Install at maximum distance from high-voltage cables and power equipment.

Wiring Procedure

Use crimp terminals for wiring; use 3.31 mm ² –0.13 mm² wire (12-16 AWG):

1. Strip the wire to a length of 7±0.5mm (0.270–0.300“).

2. Unscrew the terminal to its widest position before inserting a wire.

3. Insert the wire completely into the terminal to ensure a proper connection.

4. Tighten enough to keep the wire from pulling free.

 Input or output cables should not be run through the same multi-core cable or share

the same wire.

 Allow for voltage drop and noise interference with I/O lines used over an extended distance.

Use wire that is properly sized for the load.

 The controller and I/O signals must be connected to the same 0V signal.

I/Os

V130/V350/V130J/V350J/V430J-RA22 models comprise a total of 12 inputs, 8 relay outputs and
2 analog outputs.

V130/V350/V130J/V350J/V430J-TRA22 models comprise a total of 12 inputs, 4 relays outputs,

4 npn outputs and 2 analog outputs.

Input functionality can be adapted as follows:

12 inputs may be used as digital inputs. They may be wired, in a group, and set to either

npn or pnp via a single jumper.

In addition, according to jumper settings and appropriate wiring:

- Inputs 5 and 6 can function as either digital or analog inputs.

- Input 0 can function as high-speed counter, as part of a shaft-encoder,
or as normal digital input.

- Input 1 can function as either counter reset, as part of a shaft-encoder,
or as normal digital input.

- If input 0 is set as high-speed counters (without reset), input 1 can function
as normal digital input.

- Inputs 7-8 and 9-10 can function as digital, thermocouple, or PT100 inputs; Input 11 can also
serve as the CM signal for PT100.

Unitronics 5