United States Stove Company 2007 User Manual
OWNER'S MANUALOWNER'S MANUAL
OWNER'S MANUAL
OWNER'S MANUALOWNER'S MANUAL
PEDESTPEDEST
PEDEST
PEDESTPEDEST
T
E
A
T
S
T
I
N
U
U
E
C
S
D
S
O
M
S
N
A
P
S
T
O
C
Y
V
E
AL PLAAL PLA
AL PLA
AL PLAAL PLA
MODELMODEL
MODEL
MODELMODEL
20072007
2007
20072007
TE HEATE HEA
TE HEA
TE HEATE HEA
A
T
S
D
E
T
I
N
U
S
U
S
C
O
M
P
TERTER
TER
TERTER
T
E
S
S
T
O
V
E
C
Y
N
A
EXEMPT PER
EPA METHOD 28A
SAFETY NOTICE:SAFETY NOTICE:
SAFETY NOTICE:
SAFETY NOTICE:SAFETY NOTICE:
CAUTION!CAUTION!
CAUTION!
CAUTION!CAUTION!
Read All Instructions CarefullyRead All Instructions Carefully
Read All Instructions Carefully
Read All Instructions CarefullyRead All Instructions Carefully
Before Starting The InstallationBefore Starting The Installation
Before Starting The Installation
Before Starting The InstallationBefore Starting The Installation
or Operating This Heater.or Operating This Heater.
or Operating This Heater.
or Operating This Heater.or Operating This Heater.
Improper Installation Could VoidImproper Installation Could Void
Improper Installation Could Void
Improper Installation Could VoidImproper Installation Could Void
Your Warranty!Your Warranty!
Your Warranty!
Your Warranty!Your Warranty!
SAVE THIS MANUAL FOR FUTURE REFERENCESAVE THIS MANUAL FOR FUTURE REFERENCE
SAVE THIS MANUAL FOR FUTURE REFERENCE
SAVE THIS MANUAL FOR FUTURE REFERENCESAVE THIS MANUAL FOR FUTURE REFERENCE
THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLETHIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE
THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE
THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLETHIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE
YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
UNITED STATES STOVE COMPANYUNITED STATES STOVE COMPANY
UNITED STATES STOVE COMPANY
UNITED STATES STOVE COMPANYUNITED STATES STOVE COMPANY
If this heater is not properly installed, a house fire mayIf this heater is not properly installed, a house fire may
If this heater is not properly installed, a house fire may
If this heater is not properly installed, a house fire mayIf this heater is not properly installed, a house fire may
result. For your safety, follow the installation instruc-result. For your safety, follow the installation instruc-
result. For your safety, follow the installation instruc-
result. For your safety, follow the installation instruc-result. For your safety, follow the installation instructions. Contract local building or fire officials abouttions. Contract local building or fire officials about
tions. Contract local building or fire officials about
tions. Contract local building or fire officials abouttions. Contract local building or fire officials about
restrictions and installation requirements in your area.restrictions and installation requirements in your area.
restrictions and installation requirements in your area.
restrictions and installation requirements in your area.restrictions and installation requirements in your area.
DO NOT USE THIS HEATERDO NOT USE THIS HEATER
DO NOT USE THIS HEATER
DO NOT USE THIS HEATERDO NOT USE THIS HEATER
IN A MOBILE HOME OR TRAILERIN A MOBILE HOME OR TRAILER
IN A MOBILE HOME OR TRAILER
IN A MOBILE HOME OR TRAILERIN A MOBILE HOME OR TRAILER
Distributed By:Distributed By:
Distributed By:
Distributed By:Distributed By:
227 INDUSTRIAL PARK ROAD227 INDUSTRIAL PARK ROAD
227 INDUSTRIAL PARK ROAD
227 INDUSTRIAL PARK ROAD227 INDUSTRIAL PARK ROAD
P.O. BOX 151P.O. BOX 151
P.O. BOX 151
P.O. BOX 151P.O. BOX 151
SOUTH PITTSBURG, TN 37380SOUTH PITTSBURG, TN 37380
SOUTH PITTSBURG, TN 37380
SOUTH PITTSBURG, TN 37380SOUTH PITTSBURG, TN 37380
1
TESTED TO
UL 1482
&
CAN/ULC - S627
2720 B2720 B
2720 B
2720 B2720 B
CONGRACONGRA
CONGRA
CONGRACONGRA
You've purchased a heater from North America's oldest manufacturer of wood burning products.
By heating with wood you're helping to CONSERVE ENERGY!
Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at
least one tree each year. Future generations will thank you.
tools and materials neededtools and materials needed
tools and materials needed
tools and materials neededtools and materials needed
TOOLSTOOLS
TOOLS
TOOLSTOOLS
Pencil
6 Foot Folding Rule or Tape Measure
Drill, Hand or Electric
Drill Bit 1/8" Dia. (For Sheet Metal Screws)
5/16" Nut Driver or
5/16" Socket w/Ratchet
Screw Driver (Blade-Type)
Gloves
Safety Glasses
DimensionsDimensions
Dimensions
DimensionsDimensions
TULATULA
TULA
TULATULA
TIONS!TIONS!
TIONS!
TIONS!TIONS!
MATERIALSMATERIALS
MATERIALS
MATERIALSMATERIALS
6" Pipe, 6" Elbow, Collar and Thimble; As Required
(24 gauge min.)
1/2" Sheet Metal Screws (No. 10A x 1/2")
6" Inside Diameter Underwriters Laboratories (UL)
Listed Residential Solid Fuel Factory-Built
Triplewall Chimney or Exiting Masonry Chimney.
In Canada, chimney must comply with CAN/ULC S629
Floor Protector Material As Specified in
Figures 2,3, &4.
Furnace Cement (Manufacturer Recommends:
Rutland Black Code 78 or Equivalent)
(TOP VIEW)
(FRONT VIEW)
(SIDE VIEW)
2
SAFETY RULESSAFETY RULES
SAFETY RULES
SAFETY RULESSAFETY RULES
SAFETY NOTICE: SAFETY NOTICE:
SAFETY NOTICE: If this heater is not properly installed a house fire may result. For your safety, follow the
SAFETY NOTICE: SAFETY NOTICE:
installation directions. Contact local building or fire officials about restrictions and installation inspection
requirements in your area.
Read these rules and the instructions carefully.
Check with local codes. The installation comply
1.
with their rulings. Observe closely the clearances to combustibles (page 4).
Do not install this heater in a mobile home or
2.
trailer.
DO NOT connect a wood burning heater to an
aluminum Type B gas vent. This is not safe and
is prohibited by the National Fire Protection
Association Code and Canadian Standards.
Always connect this heater to a chimney and vent
3.
to the outside. Never vent to another room or
inside a building.
The freestanding room heater requires a ma-
4.
sonry or a UL/ULC Listed Residential Type and
Building Heating Appliance Chimney.
Be sure that your chimney is safely constructed
5.
and in good repair. Have the chimney inspected
by the Fire Department or a qualified inspector.
Your insurance company may be able to recommend a qualified inspector.
12.
13.
14.
15.
Disposal of Ashes- Place ashes in a metal
container with a tight fitting lid. Keep the closed
container on a non-combustible floor or on the
ground, well away from all combustible materials. Keep the ashes in the closed container
until all cinders have thoroughly cooled. The
ashes may be buried in the ground or picked up
by a refuse collector.
Keep the firebox section free of excess ashes.
Observe clearances to combustible materials
specified in this manual to avoid a fire hazard.
CARING FOR PAINTED PARTS- This heater
has a painted jacket, which is durable but it will
not stand rough handling or abuse. When
installing your heater, use care in handling.
Clean with soap and warm water when heater
is not hot. DO NOT use any acids or scouring
soap, as these wear and dull the finish. PAINT
DISCOLORATION WILL OCCUR IF THE
HEATER IS OVERFIRED. FOLLOW OPERATING INSTRUCTIONS CAREFULLY.
Make sure the chimney is high enough to give a
6.
good draft.
Inspect chimney connector and chimney twice
7.
monthly during the heating season for any deposit of creosote or soot which must be removed
(see Chimney Maintenance, page 10).
DO NOT BE ALARMED IF HEATER SMOKES
8.
UPON INITIAL FIRING. The special paint used
on this heater must be cured during initial firing.
This smoking will occur only on initial firing.
CAST IRON PARTS MUST BE "SEASONED" TO
9.
AVOID CRACKING. BUILD ONLY SMALL FIRES
DURING THE FIRST FEW DAYS OF USE.
To prevent injury, do not allow anyone to use this
heater who is unfamiliar with the correct opera-
10.
tion of the heater.
For additional information on using your Room
Heater safely, obtain a copy of the National Fire
11.
Protection Association (NFPA) publication "Chimneys, Fireplaces, and Solid Fuel Burning Appliances" NFPA No. 211(USA). In Canada, obtain
a copy of CAN/CSA-B365-M91 National Standard for solid fuel burning appliances and equipment installation.
16.
17.
18.
19.
20.
21.
The firebox walls in this heater may become
slightly distorted over a period of use. The
slight distortion does not affect the operation of
the unit.
CAUTION: HOT WHILE IN OPERATION.
KEEP CHILDREN, CLOTHING, AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN
BURNS.
CAUTION: DO NOT CONNECT TO ANY AIR
DISTRIBUTION OR DUCT SYSTEM.
CAUTION: STORE SOLID WOOD FUEL A
SAFE DISTANCE AWAY. DO NOT STORE
SOLID WOOD FUEL WITHIN HEATER INSTALLATION CLEARANCES OR WITHIN
THE SPACE REQUIRED FOR ASH REMOVAL.
DO NOT USE A GRATE OR ELEVATE THE
FIRE.
WE RECOMMEND THAT SMOKE DETECTORS BE INSTALLED IN YOUR HOME.
CAUTION! Do not touch the metal or glass surfaces of the heater until it has thoroughly cooled.CAUTION! Do not touch the metal or glass surfaces of the heater until it has thoroughly cooled.
CAUTION! Do not touch the metal or glass surfaces of the heater until it has thoroughly cooled.
CAUTION! Do not touch the metal or glass surfaces of the heater until it has thoroughly cooled.CAUTION! Do not touch the metal or glass surfaces of the heater until it has thoroughly cooled.
3
LOCALOCA
LOCA
LOCALOCA
AS A LOCATION IS SELECTED, KEEP THE FOLLOWING IN MIND:AS A LOCATION IS SELECTED, KEEP THE FOLLOWING IN MIND:
AS A LOCATION IS SELECTED, KEEP THE FOLLOWING IN MIND:
AS A LOCATION IS SELECTED, KEEP THE FOLLOWING IN MIND:AS A LOCATION IS SELECTED, KEEP THE FOLLOWING IN MIND:
1. Keep the chimney connection as short as possible.
The heater must have its own chimney flue. Do not
connect any other appliance to the same flue. If there
is no chimney where you wish to place the heater, you
can use a UL Listed Type 103 HT, Solid Fuel, Factory
Built Chimney. (Figure 7)
2. Place the heater on solid masonry or solid concrete.
When the heater is used on a combustible floor, use a
non-combustible floor protector having a thermal con
ductivity of K=0.45 BTU in./ft. 2 hr.deg. F. with 28
gauge sheet metal or a UL Listed Floor Protector.
TING TING
TING
TING TING
THE RTHE R
THE R
THE RTHE R
OOM HEAOOM HEA
OOM HEA
OOM HEAOOM HEA
Have the floor protector with the specified dimensions.
(See Figure 2.)
3. Check Figures 2, 3, & 4. You should have at least the
clearances shown from the heater and the connector
pipe to combustible surfaces. If you have a solid brick
or stone wall behind your heater, you can place the
heater as close as you wish to the wall. If the wall is only
faced with brick or stone, treat it as a combustible wall.
TERTER
TER
TERTER
MINIMUM CLEARANCE MINIMUM CLEARANCE
MINIMUM CLEARANCE
MINIMUM CLEARANCE MINIMUM CLEARANCE
26
TT
O COMBO COMB
T
O COMB
TT
O COMBO COMB
24
TOP VIEW
Fig. 2
USTIBLE USTIBLE
USTIBLE
USTIBLE USTIBLE
MINIMUM CLEARANCES FOR
INSTALLATIONINSTALLATION
INSTALLATION IS
INSTALLATIONINSTALLATION
CORNERS OF THE HEATER TO THE NEAREST
WALL
WW
ALLSALLS
W
ALLS
WW
ALLSALLS
CORNERCORNER
CORNER
18 INCHES18 INCHES
18 INCHES FROM THE
18 INCHES18 INCHES
CORNERCORNER
CAUTION
KEEP FURNISHINGS
AND OTHER COM-
BUSTIBLE MATERIALS
AWAY FROM THE
HEATER
26
FRONT VIEW
Fig. 3
24
SIDE VIEW
Fig. 4
4
MOUNTING CAST-IRON FLUE COLLAR
This heater comes equipped with a cast-iron flue collar with holes to mount the solid damper as
shown below.
Flue Collar - 2708
Solid Damper - 2709
5/16-18 x 1-1/2" Bolts (3 req.)
Weld Tab (3 req.)
Gasket
Holes in Flue collar
where bolts attach
to heater top.
Bottom view of flue collarBottom view of flue collar
Bottom view of flue collar
Bottom view of flue collarBottom view of flue collar
with damper installedwith damper installed
with damper installed
with damper installedwith damper installed
Peel off tape from the back of
the gasket and attach the
gasket to the rope groove in
the flue collar.
Mount flue collar to the
top of the heater using the
(3) 5/16-18 x 1-1/2"
Bolts and the (3) Weld tabs
provided in the
parts bag.
The damper must
be install as shown in
this illustration. Slide
the damper into the
flue collar on an angle
and then slide the
damper handle thru
the holes in
the flue collar.
Cross-section of flueCross-section of flue
Cross-section of flue
Cross-section of flueCross-section of flue
collarcollar
collar
collarcollar
5/16-18 x 1-1/2
Bolt
Heater top
Side view of flue collarSide view of flue collar
Side view of flue collar
Side view of flue collarSide view of flue collar
mount to heater topmount to heater top
mount to heater top
mount to heater topmount to heater top
Weld Tab
5
Loading...