Unitech TB160 User Manual

10.1” Rugged Tablet Computer

- TB160 -

User's Manual

Version 1.1

unitech is a registered trademark of unitech Electronics Co., Ltd.

Revision History Date Change Description Version

2017/8/10 first published version 1.0 2019/1/7 Update spec 1.1

Preface

About This Manual

Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice. All product and company names are trademarks, service marks, or registered trademarks of their respective owners

Regulatory Compliance Statements

FCC Warning Statement

i

unitech is a registered trademark of unitech Electronics Co., Ltd.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

ii

unitech is a registered trademark of unitech Electronics Co., Ltd.

measures:

–Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting.

3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.

Operation on the 5.15 - 5.25GHz frequency band is restricted to indoor use only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the potential for harmful interference to co-channel Mobile Satellite Systems. Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and

5.725–5.850 GHz band when associated with an access point (AP).

FCC Label Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

RF Radiation Exposure Statement

For body contact during operation, this device has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

Canadian Compliance Statement

This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.

European Conformity Statement

unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive, the EMC 2014/30/EU directive and the Low Voltage 2014/35/EU directive. The declaration of conformity is available for download at :

https://portal.unitech.eu/public/Safetyregulatorystatement

CE RF Exposure Compliance

This device meets EU requirements (2014/53/EU) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. For body-worn operation, this device has been tested and meets the ICNIRP guidelines and the European Standard EN 62209-2, for use with dedicated accessories, SAR is measured with this device at a separation of 0.5 cm to the body, while transmitting at the highest certified output power level in all frequency bands of this device. Use of other accessories which contain metals may not ensure compliance with ICNIRP exposure guidelines.

CE Mark Warning

This equipment complies with the requirements of Directive 2014/53/EU of the European Parliament and Commission from 24 May, 2014 governing Radio and Telecommunications Equipment and mutual recognition of conformity. The highest CE SAR values for the device are as follows : 1.21 W/kg @ 10g

iii

unitech is a registered trademark of unitech Electronics Co., Ltd.

iv

unitech is a registered trademark of unitech Electronics Co., Ltd.

RoHS Statement

This device conforms to RoHS (Restriction Of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment.

Waste electrical and electronic equipment (WEEE)

unitech has set up a policy and process to meet the EU directive 2002/96/EC and update 2003/108/EC concerning electronic waste disposal.

For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitech’s resellers, you shall either contact your local supplier or visit us at :

https://portal.unitech.eu/public/WEEE

v

unitech is a registered trademark of unitech Electronics Co., Ltd.

Taiwan NCC Warning Statement

低功率電波輻射性電機管理辦法

第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

注意事項:

1. 使用過度恐傷害視力。

2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過

1小時。

3. 減少電磁波影響，請妥適使用。

Laser Information

The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or prescribed service operations.

The laser safety warning label required by the DHHS/IEC for the unitech product’s optional laser scanner module is located on the memory compartment cover, on the back of the unit.

* Laser information only applies to the products with laser components.

CAUTION! Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner, including binoculars, microscopes, and magnifying glasses, with will increase eye damage. This does not include eyeglasses worn by the user.

LED Information

The unitech product contains LED indicator(s) or LED ring whose luminance is not harmful to human eyes during normal operation, user maintenance or prescribed service operations.

*LED information only applies to the products with LED components.

vi

unitech is a registered trademark of unitech Electronics Co., Ltd.

Battery Notice

1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures.

2. If a battery performance decreases more than 20%, the battery is at the end of its life cycle. Stop use and ensure the battery is disposed of properly.

3. The length of time that a battery lasts depends on the battery type and how the device is used. Conserve the battery life by doing the following:

 Avoid fully uncharging the battery because this places additional

strain on it. Several partial uncharges with frequent charges are better than a fully uncharged battery. Charging a partially charged battery does not cause harm to the unit.

 Keep the battery cool. Avoid hot vehicles. For prolonged

storage, keep the battery at a 40% charge level.

 Do not leave the battery uncharged and unused for an extended

period of time, the battery will wear out and the longevity of the battery will be at least half of one with frequent charges.

4. Protect battery life by not over or under charging the battery.

5. Please do not leave battery unused for long time without charging it. Despite unitech’s safety precautions, the battery pack may begin to change shape. If so, stop using it immediately. Please check to see if you are using a proper power adapter to charge the battery or contact your service provider for service.

6. If you cannot charge the battery after it has been idle for an extended period of time and it begins to heat up, please do not try to charge it. It may not be functional anymore.

7. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by unitech’s warranty policy.

vii

unitech is a registered trademark of unitech Electronics Co., Ltd.

viii

unitech is a registered trademark of unitech Electronics Co., Ltd.

 RISK OF EXPLOSION IF BATTERY IS

REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

 如果更換不正確之電池行事會有爆炸的風險

請依製造商說明書處理用過之電池

CAUTION!

 如果更换不正确之电池行事会有爆炸的风险

请依制造商说明书处理用过之电池

Battery charge notice

It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0°C to 40°C. Charging batteries outside of the specified range could damage the batteries and shorten their life cycle.

CAUTION! Do not charge batteries at a temperature lower than 0°C. This will

make the batteries unstable and dangerous. Please use a battery temperature detecting device for a charger to ensure a safe charging temperature range.

CAUTION! To ensure the unit working properly, please keep all connectors

away from the contaminants staying inside of them such as dust, grease, mud, and water. The negligence may cause the unit with no communication, short circuited, overheated and so on.

CAUTION! If the connector is damaged, please ensure the connector is being

fully repaired before use the unit to avoid causing short circuited.

Storage and safety notice

Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20°C to 60°C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature.

* The message above only applies to the usage of the removable batteries.

For the products with non-removable batteries / without batteries, please refer to the specification of each product.

Product Operation and Storage Notice

The unitech product has applicable operation and storage temperature conditions. Please follow the limitation of suggested temperature conditions to avoid failure, damage or malfunction.

*For applicable temperature conditions, please refer to the specification of each

product.

Adapter Notice

1. Please do not leave the power adapter in the socket when it is not connected to your unitech product for charging.

2. Please remove the power adapter when the battery is fully recharged.

3. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.

4. Please only use the bundled power adapter or same specification of adapter to charge your unitech product. Using the wrong power adapter can damage your unitech product.

* The message above only applies to the product connected to the adapter.

For the products without using the adapters, please refer to the specification of each product.

ix

unitech is a registered trademark of unitech Electronics Co., Ltd.

Hearing Damage Warning

Zx.3 Warning

The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following:

- the symbol of Figure 1 with a minimum height of 5 mm; and

- the following wording, or similar :

To prevent possible hearing damage, do not listen at high volume levels for long periods.

Alternatively , the entire warning m ay be given through the eq uipment displ ay during u se, whe n the user is asked to acknowledge activation of the higher level.

x

unitech is a registered trademark of unitech Electronics Co., Ltd.

Worldwide Support

unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below:

Taipei, Taiwan – Headquarters Europe

Tel:

+886-2-89121122

Tel:

+31-13-4609292

E-mail:

info@hq.ute.com

E-mail:

info@eu.ute.com

Address:

5F, No. 136, Lane 235, Baoqiao Road, Xindian District, New Taipei City 231, Taiwan (R.O.C.)

Address:

Kapitein Hatterasstraat 19, 5015 BB, Tilburg, the Netherlands

xi

unitech is a registered trademark of unitech Electronics Co., Ltd.

Website:

http://www.ute.com

We

bsite:

http://eu.ute.com

China Japan

Tel:

+86-59-2310-9966

Tel:

+81-3-35232766

E-mail:

info@cn.ute.com

E-mail:

info@jp.ute.com

Address:

Website:

Room401C, 4F, RIHUA International Mansion, Xinfeng 3nd Road, Huoju Hi-tech District, Xiamen, Fujan , China

http://cn.ute.com

Address:

Website:

Kayabacho Nagaoka Building 8F.,1-5-19 Shinkawa, Chuo-Ku, Tokyo, 104-0033, Japan

http://jp.ute.com

Asia & Pacific / Middle East Latin America

Tel:

+886-2-27911556

Tel:

+52-55-5171-0528

E-mail:

info@apac.ute.com info@india.ute.com info@

mideast.ute.com

E-mail:

Address:

info@latin.ute.com 1717

1 Park Row, Suite 210

Houston, TX 77084USA (Rep.)

Address:

4F., No. 236, ShinHu 2nd Rd., NeiHu Chiu, 114, Taipei,Taiwan

Website:

http://latin.ute.com

Website:

http://apac.ute.com / http://mideast.ute.com

North America Please scan QR Code to visit us :

Tel:

+1-714-8916400

E-mail:

Address:

Website:

info@us.ute.com / info@can.ute.com 6182 Katella Ave, Cypress, CA 90630, USA

http://us.ute.com

Warranty Policy

The following items covered under the unitech Limited Warranty are free from defects during normal use:

The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product.

Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.

xii

unitech is a registered trademark of unitech Electronics Co., Ltd.

Table of Contents

Preface.............................................................................................................i

Regulatory Compliance Statements..............................................................i

Laser Information ........................................................................................vi

LED Information ..........................................................................................vi

Battery Notice ............................................................................................. vii

Adapter Notice............................................................................................. ix

Hearing Damage Warning............................................................................x

Worldwide Support.......................................................................................x

Warranty Policy.......................................................................................... xii

Chapter 1 - Overview................................................................................1

1.1 Package .................................................................................................1

1.2 Product Detail.........................................................................................2

1.3 Specifications.........................................................................................7

1.4 Getting Started .....................................................................................10

Chapter 2 – Installation & Operation.................................................20

2.1 Opening the I/O Compartment Cover...................................................20

2.2 Closing the I/O Compartment Cover ....................................................21

2.3 Connecting to External Cabling............................................................22

2.3 Installing the standard Battery..............................................................25

2.4 Removing the standard Battery............................................................26

2.5 Connecting to a Wireless Network .......................................................27

2.6 Handstrap, Carrying Handle and Shoulder Strap.................................28

2.7 Barcode Scan.......................................................................................32

2.8 GPS Function Demo ............................................................................33

2.9 NFC Test Guide....................................................................................36

2.10 TB160 Recovery.................................................................................37

Chapter 3 – Introduction to Applications.........................................39

3.1 When to use the BIOS Setup ...............................................................39

xiii

unitech is a registered trademark of unitech Electronics Co., Ltd.

xiv

unitech is a registered trademark of unitech Electronics Co., Ltd.

3.2 Accessing the BIOS Setup Utility..........................................................40

3.3 EC and BIOS........................................................................................44

3.4 DashOn Utility device...........................................................................49

3.5 CamOn Setting.....................................................................................52

TB160 User’s Manual

Chapter 1 - Overview

1.1 Package

Please make sure the following contents are in the TB160 gift box. If something is missing or damaged, please contact your unitech representative.

The standard package contents

 TB160  Power Adapter  Stylus  2-Point Carrying Handle  2-Point Shoulder Strap  4-Point Handstrap  Hitch D-rings (Attaching straps)  Regulatory Compliance Statements  Quick start Guide  QR code card

1

unitech is a registered trademark of unitech Electronics Co., Ltd.

TB160 User’s Manual

1.2 Product Detail

TB160 Front View

2

unitech is a registered trademark of unitech Electronics Co., Ltd.

1 Left view 2 Front view 3 Rear view 4 Right view 5 Rubber bumpers 6 Bottom view

3

unitech is a registered trademark of unitech Electronics Co., Ltd.

TB160 User’s Manual

1 Front camera 8 Volume + 2 Touch screen 9 Volume 3 Barcode trigger 10 Power key 4 Battery LED 11 Power LED 5 Wi-Fi LED 12 F2 key (Programmable function key) 6 FN LED 13 F1 key (Programmable function key) 7 Home key 14 FN key (Programmable function key)

TB160 User’s Manual

TB160 Rear View

4

unitech is a registered trademark of unitech Electronics Co., Ltd.

1 Battery 2 Rear camera 3 Barcode reader 4 NFC sensing area 5

Securing holes 6 Expansion bay 7 Stylus holder

5

unitech is a registered trademark of unitech Electronics Co., Ltd.

TB160 User’s Manual

TB160 Side and Bottom View

1 Left I/O compartment cover

(USB 2.0 port)

9 USB 3.0

2 Micro HDMI 10 Audio jack 3 MicroSD slot 11 Ethernet 4 Left I/O compartment cover 12 DC-IN Jack 5 Tether hole 13 RS-232 6 USB 2.0 14 DC-IN cover 7 Battery switch 15 Right I/O compartment cover 8 Micro SIM slot

Unitech TB160 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual