Unitech MS650 Quick Manual

Page 1
MS650 Wireless CCD Ring Scanner
Quick Guide
because we care
For more detailed scanner setting, please go to www.ute.com to download the user manual.
Page 2
FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de las classe B prescrites dans le Réglement sur le brouillage radioélectrique édicté par les ministère des Communica­tions du Canada.
CE MARKING AND EUROPEAN UNION COMPLIANCE
Testing for compliance to CE requirements was performed by an independent laboratory. The unit under test was found compliant with all the applicable Directives, 2014/30/EU, 2014/35/EU and 2014/53/EU.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and importers to take-back electronic products at the end of their useful life.
ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2002/95/EC.
NON-MODIFICATION STATEMENT
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
RoHS
- 1 -
1. Take any metals into contact with the terminals in connectors.
2. Use the scanner where any inflammable gases.
If following condition occur, immediately power off the host computer, disconnect the interface cable, and contact your nearest dealer.
1. Smoke, abnormal odors or noises come from the scanner.
2. Drop the scanner so as to affect the operation or damage its housing.
Do Not
Do not do behavior below.
1. Put the scanner in places excessively high temperatures such as expose under direct sunlight.
2. Use the scanner in extremely humid area or drastic temperature changes.
3. Place the scanner in oily smoke or steam environment such as cooking range.
4. Be covered or wrapped up the scanner in bad-ventilated area such as under cloth or blanket.
5. Insert or drop foreign materials or water into scanning window or vents.
6. Using the scanner while hand is wet or damp.
7. Use the scanner with anti-slip gloves containing plasticizer and chemicals or organic solvents such as benzene, thinner, insecticide etc to clean the housing. Otherwise, it could not result fire and electrical shock but housing may be broken and injured.
8. Scratch or modify the scanner and bend, twist, pull or heat its interface cable.
9. Put heavy objects on interface cable.
Do not stare the light source from the scanning window or do not point the
scanning window at other people’s eyes or eyesight may be damaged by direct exposure under the light.
Do not put the scanner on an unstable or inclined plane. The scanner may drop, creating injuries.
Once the interface cable is damaged such as exposed or broken copper wires, stop using immediately and contact your dealer. Otherwise, it could result fire or electrical shock.
WARNING AND CAUTION
- 2 -
Page 3
- 3 -
INTRODUCTION
SPECIFICATIONS
Sensor Linear Image Sensor Resolution 4mil/ 0.1mm Indicator LED, Buzzer PCS 30% Housing Plastic(PC+ABS) Profile BT HID, USB HID, USB VCP, Batch Mode
Battery Life 6000 scans (1 scan/ 5 sec)
Charge Time 2.5 hours (fully charged) Radio Bluetooth 4.1 (Class2) Coverage 10M/33ft. (line of sight) Symbologies All major 1D barcodes incl. GS1 Databar
- 4 -
BEEPER INDICATION
LED INDICATION
Off Flashing Blue One Green Flash Flashing Red Solid Red
Standby or Power off Disconnected or Discoverable Good Read Low power Charging
Single beep Good read Single short beep The scanner reads a Code39 of ASCII in configuration procedure Two beeps i. Wireless connection ii. The scanner successfully reads
a configuration barcode
Four beeps
(Hi-Lo-Hi-Lo) Out of range/Poor connection
Five beeps Low power
Three beeps Wireless disconnection Three short beeps i. The scanner reads a barcode
while disconnected.
ii. The scanner reads an unexpected barcode during configuration procedure. (scan [ABORT] to abort and start over)
iii. Memory full
LED Indicator
Micro USB port
(with Protective Cover)
Touch-Activated Trigger Button
Function Button
Exit Window
Restart Button
(insert pin into the hole)
Page 4
- 5 - - 6 -
OUT OF THE BOX
Regulatory Compliance Statements
Spare Velcro Strap
USB Charger Cable
Wireless CCD Ring Scanner
Quick Guide
1
2
MS650 Wireless CCD Ring Scanner
Quick
G
uid
e
because we care
Regulatory Compliance Statements Part No. XXXXXXX FCC Warning Statement This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protect­ion against harmful interference in a residential installation.
CHARGING THE BATTERY
ATTENTION
1. Flip open the micro USB port on the scanner.
2. Insert the micro USB connector into the port on the scanner and USB A connector into a USB port on the host PC.
3. Keep charging until the red LED indicator turns off.
1. It is strongly recommended to dry your hand and the velcro strap if either of them is soaking wet. The scanner may still work in wet condition, but its touch-activated button can be too responsive so as to trigger the scanning from time to time, draining battery quickly as a result.
2. The following gloves have been tested to be working with the touch-activated button: latex examination glove, antistatic glove, white cotton glove (with or without latex coating), safety glove, and rubber glove. However, it is still recommended to operate with bare hand to ensure the responsiveness of touch­ activated button.
Scanner
Micro USB
USB A
Host
Page 5
STEP 1 - GETTING STARTED
- 7 - - 8 -
1. Pull open the long strap and insert your index finger through the loop.
2. Adjust and attach the long strap for a comfortable fit.
3. Clench your fist and use your thumb to tap the touch-activated trigger button.
4. Aim at the barcode you wish to scan.
Page 6
- 9 - - 10 -
. F064$
*.F064$*
. F065$
*.F065$*
. F066$
*.F066$*
Scan one of below configuration barcodes to determine which touch-sensing button to enable according to your habit:
STEP 2 - BUTTON PREFERENCE
Right Button Only
Left Button Only
Both Buttons
Scan one of below configuration barcodes to determine your interface:
STEP 3 -
INTERFACE SELECTION
[ Recommended ]
. C006$
*.C006$*
USB VCP
. C008$
*.C008$*
USB HID
BT HID
. E043$
*.E043$*
Batch Mode
. C035$
*.c035$*
1. BT HID - Emulates a Bluetooth HID keyboard that transmits
barcode data to the host. (see page 11 - 12)
2.
USB HID - Emulates a USB keyboard that transmits barcode
data to the host.
3.
USB VCP - Emulates a USB virtual com device that transmits
barcode data to the host.
4.
Batch Mode - Emulates a USB mass storage device that saves
barcodes collected off-line. (see page 24 - 28)
[ For Left-handed User ]
[ For Right-handed User ]
Page 7
GETTING CONNECTED
BT - HID
- 11 - - 12 -
. E043$
BT - HID
*.E043$*
. F068$
iOS/MAC/WINDOWS
*.F068$*
. F067$
ANDROID
*.F067$*
Disconnect
1. Scan [Disconnect] to delete previous pairing record. Alternatively, you may long-press the function button for 5 seconds until the the scanner emit two beeps.
2. Scan [BT - HID]; the scanner will emit two beeps.
3. Scan either one of below barcodes according to your host system.
4.
Select “Scanner XXXXXX” on the discovered device list of your Bluetooth.
(“XXXXXX” are the last 6 digits of MAC address which can also be found on the product label)
5. The scanner will emit two beeps to verify the connection.
iOS
Android
To toggle iOS touch keyboard, please simply press the function button.
1. Enter “Settings”
2. Enter “Language & input”
3. In Keyboard & input window, tap “Default” to continue.
4. Turn off “Hardware - Physical keyboard”, and the Touch Keyboard will function properly again.
SMARTPHONE/TABLET TOUCH KEYBOARD
Please follow below instruction to toggle touch keyboard on smartphone/tablet.
. E031$
*.E031$*
BT - HID
Function Button
Page 8
- 13 - - 14 -
NUMERIC BARCODES
1
*1*
2
*2*
3
*3*
4
*4*
5
*5*
6
*6*
7
*7*
8
*8*
9
*9*
0
*0*
Variable Timeout
No Timeout (Scanner Always On)
*.B030$*
. B030$
SET MINUTE
*.B029$*
. B029$
SET SECOND
*.B021$*
. B021$
DISABLE TIMEOUT
The default timeout is 00 minute and 30 seconds. For example, to set the timeout as 5 minutes 30 seconds:
1. Scan [Set Minute]
2. Scan [0] & [5] on page 14.
(Range: 00 ~ 60)
(Range: 00 ~ 60)
3. Scan [Set Minute]
4. Scan [Set Second]
5. Scan [3] & [0] on page 14.
6. Scan [Set Second]
The period of inactivity before auto power-off.
POWER OFF TIMEOUT
BT - HID
Warning! This will cause the battery to drain quickly.
Page 9
GENERAL SETTINGS ILLUMINATION PREFERENCE
BEEPER
. P023$
. A007$
. F012$
ABORT
CHECK VERSION
BEEP OFF
. F018$
- 15 - - 16 -
. A001$
DEFAULT
BEEP ON
LASER ALWAYS ON LED AUTO-ADAPTIVE
LASER ALWAYS ON LED ON AFTER 1 SEC
. F059$
*.F059$*
. F049$
*.F049$*
LASER ALWAYS ON LED ALWAYS ON
. F048$
*.F048$*
LASER OFF LED ALWAYS ON
. F046$
*.F046$*
Page 10
KEYBOARD LAYOUT
. C010$
ENGLISH (USA)
. C018$
ENGLISH (UK)
. C011$
GERMAN
. C012$
FRENCH
. C013$
SPANISH
. C014$
ITALIAN
. C009$
JAPAN (106 key)
- 17 - - 18 -
CANADIAN (TRADITIONAL)
. C034$
NORWEGIAN
. C029$
SWEDISH
. C026$
PORTUGUESE
. C031$
CANADIAN (FRENCH)
. C025$
Page 11
HUNGARIAN (101 KEY)
BRAZILIAN (PORTUGUESE)
SLOVAK
SWISS (FRENCH)
DUTCH
DANISH
BELGIAN (AZERTY)
. C016$
SWISS (GERMAN)
KEYBOARD LAYOUT
. C017$
CZECH (QWERTY)
. C022$
CZECH (QWERTZ)
HUNGARIAN (QWERTZ)
. C021$
. C015$
ALT CODE
- 19 - - 20 -
. C024$
. C023$
. C033$
. C032$
. C027$
. C028$
. C030$
Page 12
ENABLE SYMBOLOGIES
ENABLE ALL CODE
. A002$
. K010$
CODE 32
. L010$
. N001$
. M010$
. L001$
UK PLESSEY
MSI
INDUSTRIAL 2 OF 5
MATRIX 2 OF 5
CODE 93
. L014$
. G010$
. N017$
. N032$
. N010$
. N026$
IATA
TELEPEN
GS1 DATABAR
GS1 DATABAR LIMITED
GS1 DATABAR EXPANDED
- 21 - - 22 -
Page 13
TERMINATOR
LF
CR + LF
NONE
SPACE
TAB
. D012$
CR
. D011$
. D013$
. D010$
. D015$
. D014$
- 23 - - 24 -
BATCH MODE
After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR >
To retrieve stored data, please connect the scanner to the host with cable, access removable storage device “MiniScan” from which you may open or copy the file “BARCODE.txt” to your computer.
To delete ONE stored data, please scan below barcode. Alternatively, you may press the function button once.
. R005$
*.R005$*
. C035$
*.c035$*
BATCH MODE
DELETE LAST DATA
To delete ALL stored data, simply delete the file “BARCODE.txt” in the removable storage device “MiniScan” until you hear two beeps.
Page 14
- 25 - - 26 -
Example: To change Data Format to
<Barcode Data>, <Date>, <Time>
1. Scan [
Data Format
]
2. Scan [4], [2], [3] on page 14.
3. Scan [
Data Format
]
The default Data Format is <Date>, <Time>,
<Barcode Data> only
below are all items available for display and their codes:
Default is comma ( , ) You may replace it with any alphanumeric characters from the full ASCII table in Full User’s Manual.
Example: To change Field Separator to Semicolon ( ; )
1. Scan [
Field Separator
]
2. Scan [ ; ] from the full ASCII table.
3. Scan [
Field Separator
]
. R010$
*.R010$*
FIELD SEPARATOR (DELIMITER)
. R011$
*.R011$*
DATA FORMAT
2 4
Date Barcode Data
Code Item Code Item
3 Time
Example: To set Date to 2017-08-01 (Year-Month-Day):
1. Scan [
Set Date
]
2. Scan [1], [7], [0], [8], [0], [1] on page 14.
3. Scan [
Set Date
]
Example: To set Time to 08:10:30 am (Hr:Min:Sec)
1. Scan [
Set Time
]
2. Scan [0], [8], [1], [0], [3], [0] on page 14.
3. Scan [
Set Time
]
. R006$
*.R006$*
SET DATE
. R007$
*.R007$*
SET TIME
* Full drain of battery may cause the Time and Date to stop. To avoid this, please, please fully charge the scanner for at least 1 hour before use.
BATCH MODE
DATE & TIME SETUP
BATCH MODE
DATA FORMAT
Page 15
- 27 - - 28 -
The default Date Format is DD/MM/YYYY (Code = 09), below is full list of available formats and their setup codes:
Example: To set Date Format to MM/DD/YY (Code =12)
1. Scan [
Date Format
]
2. Scan [1], [2] on page 14.
3. Scan [
Date Format
]
. R008$
*.R008$*
DATE FORMAT
01 02 03 04 05 06 07 08
DD-MM-YYYY MM-DD-YYYY DD-MM-YY MM-DD-YY YYYY-MM-DD YY-MM-DD DD-MM MM-DD
Code Format Code Format
09 10 11 12 13 14 15 16
DD/MM/YYYY MM/DD/YYYY DD/MM/YY MM/DD/YY YYYY/MM/DD YY/MM/DD DD/MM MM/DD
The default Time Format is HH:MM:SS (Code = 01), below are available formats and their setup codes:
Example: To set Time Format to HH:MM (Code = 02)
1. Scan [
Time Format
]
2. Scan [0], [2] on page 14
3. Scan [
Time Format
]
. R009$
*.R009$*
TIME FORMAT
01 HH:MM:SS
Code Format Code Format
02
HH:MM
BATCH MODE
DATE FORMAT
BATCH MODE
TIME FORMAT
Page 16
- 29 - - 30 -
HOW TO REMOVE VELCRO STRAP
2. Pull out the long strap through the slot.
1. Pull open the long strap.
3. Pull open the short strap on the other side.
4. Keep pulling the short strap until the whole velcro strap is removed from the scanner.
Page 17
- 31 - - 32 -
HOW TO INSTALL VELCRO STRAP (RIGHT HANDED USER)
2. Pull the long strap to the end.
1. Insert the long strap through the left slot, with velcro side facing downwards.
3. Insert the long strap through the other slot, with velcro side facing upwards.
4. Attach the long strap to itself to close.
Page 18
- 33 - - 34-
HOW TO INSTALL VELCRO STRAP (LEFT HANDED USER)
2. Pull the long strap to the end.
1. Insert the long strap through the right slot, with velcro side facing downwards.
3. Insert the long strap through the other slot, with velcro side facing upwards.
4. Attach the long strap to itself to close.
Page 19
TEST BARCODES
EAN
Code 128
12345678
Code 39
CODE-39 TEST
Interleaved 2 of 5
9876543210
7164154
942052
TROUBLESHOOTING
Q: Your Bluetooth is unable to detect the scanner. A:
(1) Make sure your Bluetooth version is 4.0 or later. (2) Restart your Bluetooth or Host device and try again, following the instruction on page 11. (3) Make sure the scanner is in BT-HID mode (see page 10). If the scanner is discoverable, its LED indicator will be flashing Blue. (4) The scanner might be powered off. By default the scanner goes to sleep after 30 seconds of inactivity. You can re-activate the scanner by touching the scan button on both sides. Alternatively, you may also increase the power off timeout (see page 13) so that the scanner will stay awake longer.
Q: Your Bluetooth can detect the scanner, but it cannot pair with the scanner successfully.
(1) Make sure your Bluetooth version is 4.0 or later. (2) Restart your Bluetooth or Host device and try again, following the instruction on page 11. (3) Make sure to remove the scanner from the Bluetooth of host device that has previously paired with the scanner. (4) Follow the instruction on page 11 and try again.
A:
Q: The scanner does not read barcode instantly.
(1) Barcode print quality is too poor. (2) The ambient light is too weak. If that’s the case, configure the LED illumination to auto-adaptive or always on (see page 16)
A:
Q: The scanner does not output barcode data as expected.
(1) The keyboard layout of scanner does not match that of your host device. Try configuring keyboard layout on page 17 - 20.
A:
- 35 - - 36-
Loading...