Unitech MS250 User Manual

Download

Page 1

CCD Barcode Scanner

- MS250 -

User’s Manual

Version 2.0

Page 2

Disclaimer

Unitech reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Unitech to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Unitech.

Unitech shall not be liable for technical or editorial errors or omissions contained herein: nor for incidental or consequential damages resulting from the furnishing, performance, or use of this manual.

This document contains propriety information that is protected by copyright. All rights reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Unitech.

Trademarks

Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are the property of their respective owners.

Regulatory Compliance Statements

RoHS Statement

This device conforms to RoHS (Reduction Of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment.

Page 3

Table of Contents

Disclaimer ................................................................................................................... I

Trademarks ................................................................................................................. I

Regulatory Compliance Statements ............................................................................ I

Table of Contents ....................................................................................................... II

Chapter 1. Quick Tour ................................................................................................ 1

Chapter 2. Installation and Operation ........................................................................ 2

Chapter 3. CONFIGURATION ................................................................................... 3

3.1 Flow Chart .................................................................................................... 3

3.2 Loop of Programming ................................................................................... 4

3.3 Factory Default Settings................................................................................ 4

3.4 Main Page of Configuration .......................................................................... 4

Chapter 4 Interface and Reading Mode Selection ..................................................... 6

4.1 Interface SeIection ........................................................................................ 6

4.2 Reading Mode Selection ............................................................................... 6

Chapter.5 Communication Parameters ...................................................................... 8

5.1 RS232 Communication Parameters ............................................................. 8

5.2 Keyboard Wedge Mode Parameters ........................................................... 10

5.3 Output Characters Parameters ................................................................... 13

5.4 Wand Emulation Mode Parameters ............................................................ 15

Chapter. 6 Bar Codes & Others ............................................................................... 16

6.1 SymboIogies Selection ............................................................................... 16

6.2 UPC/EANI/JAN Parameters ........................................................................ 20

6.3 Code 39 Parameters ................................................................................... 23

6.4 Code 128 Parameters ................................................................................. 25

6.5 Interleave 25 Parameters............................................................................ 27

6.6 IndustriaI 25 Parameters............................................................................. 29

6.7 Matrix 25 Parameters ................................................................................. 31

6.8 CODABAR/NW7 Parameters ...................................................................... 32

6.9 Code 93 Parameters ................................................................................... 35

6.10 Code 11 Parameters ................................................................................. 36

6.11 MSI/PLESSEY Code Parameters ............................................................. 38

6.12 LCD25 Parameters ................................................................................... 39

6.15 GS1 Databar ............................................................................................. 42

Chapter 7 Miscellaneous Parameters ...................................................................... 44

Page 4

III

7.1 Language Selection .................................................................................... 44

7.2 Bar Code ID ................................................................................................ 45

7.3 Reading Level ............................................................................................. 48

7.4 Accuracy ..................................................................................................... 48

7.5 Buzzer Beep Tone....................................................................................... 49

7.6 Sensitivity of Continuous Reading Mode .................................................... 49

7.7 Reverse Output Characters ........................................................................ 50

7.8 Setup Deletion ............................................................................................ 50

7.9 Setup Insertion ........................................................................................... 54

Appendix A Decimal Value Table .............................................................................. 58

Appendix B ASCII Table ........................................................................................... 58

Appendix C Function Key Table ............................................................................... 62

8 SPECIFICATION ................................................................................................... 63

8.1 Dimensions ................................................................................................. 63

8.2 Technical Data ............................................................................................ 64

8.3. Readable Symbology ................................................................................. 65

8.4. Reliability ................................................................................................... 66

Page 5

Chapter 1. Quick Tour

Page 6

Chapter 2. Installation and Operation

1. Connect the USB connector of MS 250 to the USB port of a host PC.

2. Aim at the barcode and pull the trigger to scan the barcode.

Page 7

Chapter 3. CONFIGURATION

3.1 Flow Chart

Page 8

3.2 Loop of Programming

The philosophy of programming parameters has been shown on the flow chart of 2.1. Basically user should

1. Scan Start of Configuration.

2. Scan all necessary labels for parameters that meet applications.

3. Scan End of Configuration to end the programming.

4. To permanently save the settings you programmed, just scan label for Save Parameters. To go back to the Default Settings, just scan label for Set All Defaults.

3.3 Factory Default Settings

The factory default settings are shown with <> and bold in the following sections. You can make your own settings by following the procedures in this manual. If you want to save the settings permanently, you should scan the label of “Save Parameters“ in chapter 2.4,otherwise the settings will not be saved after the decoder power is off, and all settings will go back to previous settings.

By scanning “Set All Default“ label, the settings will go back to the factory default settings.

3.4 Main Page of Configuration

Set AII Defaults

Start Configuration

End Configuration

Abort Configuration

Version Information

Page 9

Save Parameters -

The parameter settings will be saved permanently. Recall Stored Parameters -

Replace the current parameters by the parameters you saved last time. Set AII Defaults -

Set all the parameters to the factory default settings. Abort Configuration -

Terminate current programming status. Version Information -

Display the decoder version information and date code.

Page 10

Chapter 4 Interface and Reading Mode Selection

4.1 Interface SeIection

Keyboard Mode

RS232 Mode

WAND Emulation

Virtual Com Port Mode

4.2 Reading Mode Selection

Good Read OFF

Continuous/Trigger OFF

Testing

Page 11

Continuous/Auto Power On

Flash

Flash/Auto Power On

Reserved1

Auto Sense (Option)

Reserved3

Reserved4

Reserved5

Page 12

Chapter.5 Communication Parameters

5.1 RS232 Communication Parameters

A. Set

BAUD Rate

1200

2400

4800

<9600>

19200

38400

B. Set Up Data Bits

7 Data Bits

<8 Data Bits>

Page 13

C. Set Up Stop Bits

<1 Bit>

2 Bits

D. Set Up Parity

<None>

Even

Odd

Mark

Space

E. Handshaking

RTS/CTS Enable

Page 14

ACK/NAK Enable

XON/XOFF Enable

5.2 Keyboard Wedge Mode Parameters

A. Terminal Type

IBM PC/XT

IBM PS/2 25, 30

NEC 9800

Apple Desktop Bus(ADB)

Page 15

IBM 5550

IBM 122 Key (1)

IBM 102 Key

IBM 122 Key (2)

Reserved 1

Reserved 2

Reserved 3

Reserved 4

Reserved 5

Page 16

B. Upper/Lower Case

Upper Case

Lower Case

C. Caps Lock Detection

Enable

D. Send Character by ALT Method

Enable

Page 17

E. Select Numerical Pad

<OFF>

5.3 Output Characters Parameters

A. Select Terminator

<CR+LF>

None

Space

HT(TAB)

STX-ETX

Page 18

B. Time-out Between Characters

<0 ms>

5 ms

10 ms

25 ms

50 ms

100 ms

200 ms

300 ms

Page 19

5.4 Wand Emulation Mode Parameters

A. TTL Level Representation

Bar Equals Low

B. Scan Speed Selection

<Fast>

Slow

C. Output Format Selection

Output as Code 39 Full ASCII

Output as Original Code Format

Page 20

Chapter. 6 Bar Codes & Others

6.1 SymboIogies Selection

UPC-A <ON>

OFF

UPC-E <ON>

OFF

EAN-13/JAN-13/ISBN-13<ON>

OFF

EAN-8/JAN-8 <ON>

OFF

CODE 39 <ON>

OFF

Page 21

CODE 128 <ON>

OFF

CODABAR/NW7 <ON>

OFF

Interleave 25 <ON>

OFF

Industrial 25 ON

<OFF>

Matrix 25 ON

<OFF>

Page 22

CODE 93 ON

<OFF>

CODE 11 ON

<OFF>

China Postage ON

<OFF>

MSI/PLESSEY ON

<OFF>

Code 2 of 6 ON

<OFF>

Page 23

LCD25 ON

<OFF>

Reserved5 ON

<OFF>

Reserved6 ON

<OFF>

GS1 DataBar Omnidirectional ON

<OFF>

GS1 DataBar Limited ON

<OFF>

GS1 DataBar Expanded ON

Page 24

<OFF>

Select All Bar Codes

6.2 UPC/EANI/JAN Parameters

A Reading Type

UPCA=EAN13 ON

UPCA=EAN13<OFF>

ISBN-1C Enable

ISBN-13 <Enable>

ISSN Enable

ISSN <Disable>

Decode with Supplement

Page 25

Expand UPC-E Enable

Expand UPC-E <Disable>

EAN8=EAN13 Enable

EAN8=EAN13 <Disable>

GTIN Format Enable

GTIN Format <Disable>

B Supplemental Set Up

Transmit 2 Code

Transmit 5 Code

Page 26

Transmit 2&5 Code

C Check Digit Transmission

UPC-A Check Digit Transmission <ON>

OFF

UPC-E Check Digit Transmission <ON>

OFF

EAN-8 Check Digit Transmission <ON>

OFF

EAN-13 Check Digit Transmission <ON>

OFF

Page 27

ISSN Check Digit Transmission <ON>

OFF

6.3 Code 39 Parameters

A Type of Code

Full ASCII

Italian Pharmacy/Code 32 <OFF>

Italian Pharmacy/ Code 32 ON

B Check Digit Transmission

Calculate Check Digit & Transmit

Calculate Check Digit & Not Transmit

Page 28

C Output Start/Stop Character

Enable

D Decode Asterisk

Enable

E Set Up Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.

Fix Length (2 Sets Available)

1. 1st Set Begin

2. Decimal Value (See Appendix A)

Page 29

3. 1st Set Complete

1. 2nd Set Begin

2. Decimal Value (See Appendix A)

3. 2nd Set Complete

Minimum Length

1. Begin

2. Decimal Value (See Appendix A)

3. Complete

6.4 Code 128 Parameters

A Reading Type

UCC/EA1-128 Enable

<Enable’]C1’Code Format>

Disable‘]C1‘Code Format

Page 30

Disable Code128 Group Separators(GS)

B Check Digit Transmission

Do Not Calculate Check Digit

Calculate Check Digit & Transmit

C Append FNC2

<OFF>

D Set Up Code Length

To set the fixed length

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set.

4. Repeat the steps 1 - 3 to set additional lengths.

Page 31

Fix Length (2 Sets Available)

1. 1st Set Begin

2. Decimal Value (See Appendix A)

3. 1st Set Complete

1. 2nd Set Begin

2. Decimal Value (See Appendix A)

3. 2nd Set Complete

Minimum Length

1. Begin

2. Decimal Value (See Appendix A)

3. Complete

6.5 Interleave 25 Parameters

A Check Digit Transmission

Calculate Check Digit & Transmit

Page 32

Calculate Check Digit & Not Transmit

B Set Up Number of Character

<Even>

Odd

C Brazilian Banking Code

Enable

D Set 8p Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.

Fix Length (2 Sets Available)

1.1st Set Beg

2. Decimal Value (See Appendix A)

Page 33

3. 1st Set Complete

1.2nd Set Begin

2. Decimal Value (See Appendix A)

3. 2nd Set Complete

Minimum Length

1. Begin

2. Decimal Value (See Appendix A)

3. Compete

6.6 IndustriaI 25 Parameters

A Reading type

IATA25 Enable

B Check Digit Transmission

Page 34

Calculate Check Digit & Transmit

Calculate Check Digit & Not Transmit

C Set Up Code Length

To set the fixed length

1. Scan the “Begin“ label of the desired set.

2. Go the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set.

4. Repeat the steps 1 - 3 to set additional lengths.

Fix Length (2 Sets Available)

1. 1st Set Begin

2. Decimal Value (See Appendix A)

3. 1st Set Complete

1. 2nd Set Begin

2. Decimal Value (See Appendix A)

3. 2nd Set Complete

Page 35

Minimum Length

1. Begin

2. Decimal Value (See Appendix A)

3. Complete

6.7 Matrix 25 Parameters

A Check Digit Transmission

Calculate Check Digit & Transmit

Calculate Check Digit & Not Transmit

B Set Up Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set.

4. Repeat the steps 1 - 3 to set additional lengths.

Page 36

Fix Length (2 Sets Available)

1. 1st Set Begin

2. Decimal Value (Appendix A)

3. 1st Set Complete

1. 2nd Set Begin

2. Decimal Value (Appendix A)

3. 2nd Set Complete

Minimum Length

1. Begin

2. Decimal Value (Appendix A)

3. Complete

6.8 CODABAR/NW7 Parameters A Set Up Start/Stop Characters Upon Transmission

Page 37

<OFF>

B Transmission Type of Start/Stop

A Start

A Stop

B Start

B Stop

C Start

C Stop

D Start

Page 38

D Stop

C Set Up Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.

Fix Length (2 Sets Available)

1st Set Begin Decimal Value (Appendix A)

1st Set Complete

2nd Set Begin

Decimal Value (Appendix A)

2nd Set Complete

Page 39

Minimum Length

Begin Decimal Value (Appendix A)

Complete

6.9 Code 93 Parameters A Check Digit Transmission

Do Not Calculate Check Digit

B Set Up Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set.

4. Repeat the steps 1 - 3 to set additional lengths.

Fix Length (2 Sets Available)

1st Set Begin Decimal Value (Appendix A)

Page 40

1st Set Complete

2nd Set Begin Decimal Value (Appendix A)

2nd Set Complete

Minimum Length

Begin Decimal Value (Appendix A)

Complete

6.10 Code 11 Parameters A Check Digit Transmission

Calculate Check 1 Digit & Transmit

Calculate Check 2 Digits & Not Transmit

Page 41

Calculate Check 2 Digits & Transmit

Calculate Check 2 Digits & Not Transmit

B Set Up Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set.

4. Repeat the steps 1 - 3 to set additional lengths.

Fix Length (2 Sets Available)

1st Set Begin Decimal Value (Appendix A)

1st Set Complete

2nd Set Begin Decimal Value (Appendix A)

2nd Set Complete

Page 42

Minimum Length

Begin Decimal Value (Appendix A)

Complete

6.11 MSI/PLESSEY Code Parameters A Check Digit Transmission

Do Not Calculate Check Digit

Calculate Check Digit & Transmit

B Set Up Code Length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set.

4. Repeat the steps 1 - 3 to set additional lengths.

Page 43

Fix Length (2 Sets Available)

1st Set Begin Decimal Value (Appendix A)

1st Set Complete

2nd Set Begin Decimal Value (Appendix A)

2nd Set Complete

Minimum Length

Begin Decimal Value (Appendix A)

Complete

6.12 LCD25 Parameters A Check Digit Transmission

Calculate Check Digit & Transmit

Page 44

Calculate Check Digit & Not Transmit

B Setup Code length

To set the fixed length:

1. Scan the “Begin“ label of the desired set.

2. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the length to be read.

3. Scan the “Complete“ label of the desired set.

4. Repeat the steps 1 - 3 to set additional lengths.

Fix Length (2 Sets Available)

1st Set Begin Decimal Value (Appendix A)

1st Set Complete

2st Set Begin Decimal Value (Appendix A)

2nt Set Complete

Minimum Length

Begin Decimal Value (Appendix A)

Page 45

Complete

Fix Length (2 Sets Available)

1st Set Begin Decimal Value (Appendix A)

1st Set Complete

2nd Set Begin Decimal Value (Appendix A)

2nd Set Complete

Minimum Length

Begin Decimal Value (Appendix A)

Complete

Page 46

6.15 GS1 Databar A GS1 DataBar Omnidirectionl

Don’t Transmit Check Digit <Transmit Application ID>

Don’t Transmit Application ID Transmit Symbology ID

<Don’t Transmit Symbology ID>

B GS1 DataBar Limited Parameters

Don’t Transmit Check Digit

Page 47

Don‘t Transmit Application ID

Transmit Symbology ID

<Don‘t Transmit Symbology ID>

C GS1 DataBar Expanded Parameters

Transmit Symbology ID

<Don‘t Transmit Symbology ID>

Page 48

Chapter 7 Miscellaneous Parameters

7.1 Language Selection

UK English

Italian

Spanish

French

German

Swedish

Switzerland

Hungarian

Japanese

Page 49

Belgium

Portuguese

Denmark

Netherlands

Turkey

Reserved2

7.2 Bar Code ID

<OFF>

Default

With this function ON, a leading character will be added to the output string while

Page 50

scanning code, user may refer to the following table to know what kind of bar code is being scanned.

Please refer to the table below for matching code ID of codes read in.

Code Type

UPC-A

UPC-E

EAN-8

EAN-13

CODE 39

CODE 128

Interleave 25

Industrial 25

Matrix 25

Codabar/NW7

CODE 93

CODE 11

China Postage

MSI

LCD25

PLESSEY

GS1 DataBar Omnidirectional

GS1 DataBar Expanded

GS1 DataBar Limited

User Define Code ID

To set the code ID:

1. Scan the symbologies label.

2. Go to the ASCII Tables in Appendix B, scan label that represents the desired code ID. Note: User define code ID will override default value. Program will not check the conflict. It is possible to have more than two symbologies which have same code ID.

UPC-A

UPC-E

EAN-13/JAN-13

Page 51

EAN-8/JAN-8

CODE 39

CODE 128

CODABAR/NW7

Interleave 25

Industrial 25

Matrix 25

CODE 93

CODE 11

China Postage

MSI/PLESSEY

Page 52

LCD25

GS1 DataBar Omnidirectional ON

GS1 DataBar Limited ON

GS1 DataBar Expanded ON

Reserved5

Reserved6

7.3 Reading Level

Bar Equals High

7.4 Accuracy

1 Time

2 Times

Page 53

3 Times

4 Times

7.5 Buzzer Beep Tone

<High>

Medium

Low

Off

7.6 Sensitivity of Continuous Reading Mode

A Quick Setting:

<Fast> Slow

B Same Code Delay Reading Interval

Following code sequences represent the length of time before a barcode can be rescanned at continuous and flash reading mode. The value can be defined from 1-50 and they represent 100ms to 5 seconds in 100ms interval. Default value is 3 (0.3 seconds).

Page 54

To setup same code delay reading interval:

1.Scan the "Begin" label

2.Go the Decimal Value Tables in Appendix A, Scan label(s),that represents the same code delay reading interval. They are ranged form 1-50.One step is represented

0.1second.So the interval is from 0.1 to 5 seconds.

3.Scan the "Complete" label

4. Repeat the steps 1-3 to set time out of same symbol

Begin Decimal Value (1-50) (Appendix A)

Complete

7.7 Reverse Output Characters

<Disable> Enable

7.8 Setup Deletion

To setup the deletion of output characters:

1. Scan the label of the desired set below.

2. Scan the label of the desired symbology.

3. Go to the Decimal Value Tables listed in Appendix A, scan labels that represents the desired position to be deleted.

4. Scan "Complete" label of "Character Position to be Deleted".

5. Go to the Decimal Value Tables in appendix A,scan labels that represents the desired position to be deleted.

6. Scan the "Complete" label of "Number Position to be Deleted".

7. Repeat the steps 1 – 6 to set additional deletion.

Page 55

A. Select Deletion Set Number

1st Set

2nd Set

3rd Set

4th Set

5th Set

6th Set

B SymboIogy Selection

UPC-A

UPC-E

EAN-13/JAN-13/ISBN-13

Page 56

EAN-8/JAN-8

CODE 39

CODE 128

CODABAR/N97

Interleave 25

Industrial 25

Matrix 25

CODE 93

CODE 11

China Postage

MSI/PLESSEY

Page 57

LCD25

GS1 DataBar Omnidirectional

GS1 DataBar Limited

GS1 DataBar Expanded

All Codes

None

C Character Position to be Deleted

1. Decimal Value (Appendix A)

2. Complete

D Number of Characters to be Deleted

1. Decimal Value (Appendix A)

2. Complete

Page 58

7.9 Setup Insertion

To setup the insertion of output characters

1. Scan the label of the desired set.

2. Scan the label of the desired symbology.

3. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the desired position to be inserted.

4. Scan the “Complete“ label of “Character Position to be Inserted“.

5. Go to the ASCII Tables in Appendix B or Function Key Tables in Appendix C, scan label(s) that represents the desired characters to be inserted.

6. Scan the “Complete“ label of “Characters to be Inserted“.

7. Repeat the steps 1 - 6 to set additional insertion.

A Select Insertion Set Number

1st Set

2nd Set

3rd Set

4th Set

5th Set

6th Set

Page 59

B SymboIogies Selection

UPC-A

UPC-E

EAN-13/JAN-13/ISBN-13

EAN-8/JAN-8

CODE 39

CODE 128

CODABAR/NW7

Interleave 25

Industrial 25

Matrix 25

CODE 93

Page 60

CODE 11

China Postage

MSI/PLESSEY

LCD255

GS1 DataBar Omnidirectional

GS1 DataBar Limited

GS1 DataBar Expanded

All Codes

None

C Character Position to be Inserted

Decimal Value (Appendix A)

Complete

Page 61

D Characters to be Inserted

ASCII Table (Appendix B)

Complete

Page 62

Appendix A Decimal Value Table

0 5

1 6

2 7

3 8

4 9

Appendix B ASCII Table

NULL

STX

SOH

ETX

ENQ

EOT

ACK

BEL

HT VT LF

FF SO CR

DC1

DLE

Page 63

DC2

DC4

DC3

NAK

ETB

SYN

CAN

SUB

ESC

GS FS

RS US

SPACE

“ !

# % $

& ( ‘

) + *

, . -

/ 1 0

2 4 3

5 7 6

8 : 9

; = <

> ?

Page 64

@ B A

C E D

F H G

I K J

L N M

O Q P

R T S

U W V

X Z Y

[ ] \

^ _

` b a c e d

f h g

i k j

Page 65

l n M

o q p

r t s

u w v

x z y

﹛

} |

~ DEL

Page 66

Appendix C Function Key Table

F1 F3 F2

F4 F6 F5

F7 F9 F8

F10

F12

F11

Insert

Home

Delete

Page Up

End

Page Down

Left

Right

Down

Page 67

8 SPECIFICATION

8.1 Dimensions

Page 68

8.2 Technical Data

Interface

USB

Supply Voltage

DC +5V ± 10%

Output Voltage (Typ.)

+5V

Output low Voltage (Max.)

0.4V

Current Draw (Typ.)

± 5%

Power On (Typ.)

120mA

Stand by (Typ.)

20mA

Operation (Typ.)

120mA

Light Source

Visible Red light 635nm LED

Sensor

Linear CCD Sensor

Processor Type

ARM Cortex™-M3, 32-bit

Operating Freq.

8 MHz (Internal)

Scan Speed

200 scans/ second ±10%

Depth of Field

Up to 75mm @ 20mil, PCS90%, Code39

Width of Field (Window)

80 mm

Print Contrast Ratio

45%

Resolution

3mil (0.076mm) @ PCS90%

Ambient Light

20,000 Lux Max

Reading Angle

Test Conditions : Code 39, 10mil/0.25mm, PCS 90%

Forward & Backward

±10°~30° (±5°)

Left & Right

± 60° (±5°)

Firmware

Available for updated

Driver

Support USB emulation COM port

ESD

8kv contact, 12kv on air

Bit error rate

50/100,000

Operating Temperature

0 oC to 50 oC (32 oF to 122 oF)

Storage Temperature

-20 oC to 70 oC (-4 oF to 158 oF)

Relative Humidity

20% to 95% (Non-condensing)

Page 69

8.3. Readable Symbology

Readable

Default Enable

All UPC/EAN/JAN

EAN128 Code V V

Code 39 V V

Code 39 Full ASCII

Code32 / Italian Pharmacy

Code 128 V V

CODABAR/NW7

Interleave 25 V V

Industrial 25 V

Matrix 25 V

MSI/PLESSEY V

Code 93 V

Code 11 V

China Postage V

LCD25

GS1 DataBar Omnidirectional

GS1 DataBar Turncated

GS1 DataBar Stacked

GS1 DataBar Omnidirectional Stacked

GS1 DataBar Limited

GS1 DataBar Expanded

GS1 DataBar Expanded Stacked

Page 70

8.4. Reliability

Life Time

Trigger Switch

1,000,000 times

MTBF(Calculated)

50,000 hours

Thermal Shock

High Temp.

60 oC (140 oF)

Low Temp.

-20 oC (-4 oF)

Cycle time

20 minutes for high temp. , 20 minutes for low temp.

Cycles

5 cycles

Cable Bending Test

25,000 times/ minimum (30 times/ min @ 500g/ 90 o)

Drop

59.06 inches (150cm) drop on Concrete Surface

Beeper

90 db/ minimum