Unit USI-286 User Manual [ru]
Рукововдство пользователя
User manual
Iron/Утюг
USI-286/287
www.unit.ru
User manual | Руководство пользователя | Iron | Утюг | USI-286/287
Description
1. Spray nozzle
2. Cover of water tank
3. Steam regulator
4. Button of sprayer
5. The steam button
6. Light indicator
7. Thermoregulator
8. Power cord
9. Handle
10. Water tank
11. Soleplate
12. Button Self-clean
3
User manual | Руководство пользователя | Iron | Утюг | USI-286/287
Precautionary measures
When using the iron, take the following precautions:
Read all instructions before using
1. Use the iron only for its intended use.
2. Do not immerse the iron in w ater or any other liquid. This may lead to electric shock.
3. When connecting and disconnecting the power control of the heating must be in minimum position. When you unplug
the iron from the mains without pulling the cord, take the plug and pull easily.
4. Do not let cord touch hot soleplate. Let iron cool completely before you remove it in place.
5. Always turn of f the iron from the mains while filling his tank with water or when the water pours out of him.
6. Never allow children to use the iron without your supervision.
7. Do not leave the iron unattended connected to the mains.
8. Do not keep working iron the up sole, this may cause burns a soleplate or steam.
9. If the iron is not working proper ly, unplug it and contac t an authorized ser vice center.
10. Between ironing always place the iron upright on heel. Make sure that the iron is on a firm surface.
11. When using the iron water reservoir to be closed.
12. Use the iron only on a stable surface.
13. Do not use the iron if it is leaking or there is damage to the soleplate. Regularly check the power cord for damage.
If you find damage to the appliance, contact an authorized service center.
14. In the event of damage to the power cord contact an authorized ser vice center.
15. This appliance is not intended for use by children and persons w ith reduced physical or mental abilities.
16. Do not leave children unsupervised near the included iron.
17. Check that the device is indicated on the rating plate voltage is identical with your network.
4
User manual | Руководство пользователя | Iron | Утюг | USI-286/287
Recommendations before the start use
1. The first time the iron can smell the plastic. After a short period of time, it
will disappear.
2. Before first use, wipe the soleplate with a soft cloth.
3. Do not allow metal objects (buckles, buttons, zippers) under the sole not to
damage her.
4. Pure wool (100% wool) can be ironed steam mode. Set the steam setting to the
maximum position and use dry ironing.
Selecting the temperature
1. Refine modes ironing for clothes that you are going to iron.
2. Fabrics having any finish (applications, folds, etc.) can be ironed at the lowest
temperature.
3. If the fabric contains several kinds of fibres, select the temperature for the
tissue in which the canvas of the greatest content. For example: if the fabric
contains 60% polyester and 40% cotton, you should select the temperature
corresponding to polyester and to iron without steam.
4. First, you must determine the type of fabric for ironing. Since the sole is heated
sufficiently quickly, so begins to stroke better fabrics requiring a lower ironing
temperature, such as woven fabrics of synthetic fibers. Then, in the process
of ironing gradually move to tissues that require a higher temperature ironing.
5. Turn the temperature regulator by comparing its value with a dash in front of
it:
• position for nylon and rayon
•• position for wool, silk and mixed fabrics
••• position for cotton or linen (steaming)
Recommendations before the start use
1. Unplug the iron.
2. Set the mode switch steam to “off”.
3. Fill the tank through the opening for pouring water.
4. After completion of the work always drain the remaining water from the tank.
Do not store the iron with remaining in the tank water.
Important: If you have hard water, we recommend that you use distilled or demineralized water.
Do not use solvents or perfume water.
5
User manual | Руководство пользователя | Iron | Утюг | USI-286/287
Steam ironing
1. Fill the tank with water as described in «Filling the water tank.»
2. Connect the iron to the electrical grid.
3. Steam ironing is possible only when the maximum heating temperature of the
sole. Otherwise, no formation of steam and the water can flow through the sole.
4. Wait until the indicator light turns off, it indicates that there has been a selected
temperature.
5. Set the steam supply to the desired position.
6. At the end of the work and during breaks in ironing things set the iron in vertical
position.
7. After completing unplug the iron, pour the remaining water in it, and put to cool.
Spray
1. The spray can be used in any position, either in dry or steam ironing, as long as
the water tank is filled with water.
2. Press the spray button for this function.
NOTE: This button has to be pressed repetitively to start this function for the first
time.
Shot of steam
Shot of steam give extra steam for removing persistent wrinkles.
1. Place the temperature selector at the “max” position and wait until the pilot light
goes out
2. Wait for a few seconds for the steam to penetrate the fibre before pressing again.
3. NOTE: For the best steam quality, do not use more than three successive bursts
each time. Several pumping actions are needed to start this function.
4. Excessive use of this feature will cause the iron to cool, ensure that the pilot light
is out, before operating the shot of steam control
6
Loading...