Unipro 6003, 7003 User Manual
Functional overview Unipro 6003 / 7003 (software version 1.33/3.00)
Download QuickGuide and complete reference manual at www.uniprolaptimer.com.
ON / OF, SHOW AND DELETE DATA
On and Off: Push to turn the Laptimer on. Hold
down in app. 2 sec. to turn the Laptimer off
Show split data: Push and then Use
to scroll between laps. Push
between high and low values with
Running-in mode: With the Laptimer turned off push and hold down and then push until the display shows RUN
Shift between pit mode and driving mode: Turn the Laptimer on and Push to switch between modes
LAPTIMER SETUP
Go to Setup: Turn on the Laptimer and push Shift between setup functions: push to scroll.
Engine run time: Push and the display shows ENGINE X
Use to scroll through the engine numbers
Delete engine run time: Choose engine number and push
then push to delete the run time and to save
Wheel circumference: Push until the display shows
WHEEL SIZE Use to set the correct value
to shift between splits. Shift
Show data: Push
the laps. Shift between high and low values with
Delete data: Turn the Laptimer, then push and hold
until CLEAR LAPS is shown in the display. Push
accept the deletion
Manual change of engine run time: Choose engine number
and push
Push
THE METHOD FOR CHANGING AND DELETING SETUP
VALUES ARE COMON FOR THE SETUP MENU
Tire wear counter: Push
TIRE SET Use
numbers
and then to change the run time.
to save the changed run time.
and use to scroll through
again to
until the display shows
to scroll through the tire set
Temperature inputs: Push until the display shows TEMP INPUTS Use to choose the correct input combination.
Temperature warnings: Push until the display shows TEMP NO Use to set the warning value. The LED lamp
for the chosen input flashes. If more than one input is chosen, then push to continue to set up warning for the next input.
RPM waring: Push until the display shows
ENGINE SHIFT x,x Use
Magnet receiver setup: When using a magnet stripe receiver
you must set the number of stripes and the number of stri pes
from the pit to the finish line. Push
MAGNETS/DELAY X-X Push
chose the number of magnet stripes on the track. Push
again and use
pit to the finish line. Push
Setting up split points driving: Push and hold it down
in app. 3 seconds. Push
counter will start when you are passing the finish line on the
first lap. Push
place the split points. When the finish lin e is passed again, the
split points are saved
to set the number of stripes from the
when you come to the places you want to
to set the warning value
until the display shows
and the use to
to save
and you are ready to drive. The
Receiver type: Push until the display shows LOOP , IR
or MAGNET Use to choose receiver type
Manual setting of split points: Push
shows SPLIT X XX Push
SPLIT 1 POSITION x xx Use to set the meters
from the finish line to the first split point. Push to go to
the next split point. Continue to set all the desired split points
and push
again to save.
Use magnet stripes as split points: Pus h
display shows SPLIT X XX Push
display shows SPLIT MAGNET Push and again
to save
and the display shows YES and
and the display shows
until the display
until the
and push until the
Choose display values: Push until the display shows LEFT VALUE Choose the value for the lower left side of the display
with Push until the display shows RIGHT VALUE Choose the value for the lower right side of the display with
The values that are not shown in the lower part of the display will be shown in the upper left side of the display. You
can shift between values in the upper left side of the display with
29.01.2007
both in driving and pit mode
Display box
Display box Display box Display box
Main box
Main box
Main box Main box
RPM sensor
Magnetic receiver Magnetic receiver Loop receiver
IR receiver Water sensor
IR receiver Cylinder head sensor
Exhaust sensor
Speed kit front wheel
Exhaust sensor
Exhaust sensor
Speed kit front wheel Speed kit front wheel
Cylinder sensor Cylinder sensor
Speed kit rear axle
Cable mounting
Cable mounting
Loading...