User Guide
16FE(PoE)+2G TP/SFP Combo PoE Switch
LED
Color
Function
PWR
Green
Off: No Power supply
Light: Indicates the switch has power
LNK/ACT
Green
Off: No device is connected to the corresponding port
Light: Indicates the link through that port is successfully
established at 10/100/1000Mbps.
Blink: Indicates that the Switch is actively sending or
receiving data over that port.
Package Contents
Check the following contents of your package:
PoE Switch x 1
User Guide x 1
Power Cord x 1
Accessories(hanging ears*2,Rubber Feet*4,screw*8)
If any part is lost and damaged, please contact your local agent immediately.
Introduction
The 16FE(PoE) +2G TP/SFP Combo PoE Switch are Gigabit Uplink Unmanaged Switch which provides you with a
high-performance, low-cost, easy-to-use, seamless and standard upgrade to boost your old network to 1000Mbps.
Increase the speed of your network server and backbone connections, making Gigabit connection to a server or uplinking a
network necessarily.
Its PoE ports can automatically detect and supply power with those IEEE 802.3af/at compliant Powered Devices (PD). The
electrical power is transmitted along with data in one single cable allowing you to expand your network where there are
no power lines or outlets, where you wish to fix devices such as AP, IP Cameras or IP Phones, etc.
Hardware Description
Front Panel
The Front Panel Consists of 16-Port 10/100M Auto-Negotiation Ethernet RJ45 Ports, 2-Port Gigabit TP/SFP Combo Port. The
LED indicators also on located on the panel.
LED indicator
- 1 -
Speed
Green
Off: Indicates the link through established at 10Mbps.
Blink: Indicates the link through established at 100Mbps.
Light: Indicates the link through established at 1000Mbps.
PoE
Orange
Off: No PoE powered device (PD) connected
Light: There is a PoE PD connected to be port, which
supply power successfully.
Blink: Indicates port abnormal power supply
DIP Switch
The DIP switch located on the left panel, the default is closed. the CCTV function, When switch toggle to OFF,
all ports can communicate with each other. When DIP switch toggle to ON, 1-16 port can be isolated each other,
but 1-16 port can connect to 17T/S ,18T/S port after open CCTV to stop broadcast storm to increase forwarding rate
of frame.
Rear Panel
The rear panel of 16FE(PoE)+2G TP/SFP Combo PoE Switch indicates an AC inlet power socket, Grounding Column.
Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please follow the following instructions
in avoid of incorrect installation causing device damage and security threat.
Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with wet cloth or liquid;
Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis;
Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall;
Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of obstruction;
Make sure that the operating voltage is the same one labeled on the switch;
Do not open the chassis while the switch is operating or when electrical hazards are present to avoid electrical shocks.
- 2 -
Desktop Installation
Install the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each corner of the
Switch in case of the external vibration. Allow adequate space for ventilation between the device and the objects around it.
The installation diagram is as follows:
Rack-mountable Installation
The switch is rack-mountable and can be installed on an EIA-19 inch equipment rack. To do this, first, please install the
mounting brackets on the switch’s side panels (one on each side), secure them with the included screws, and then use the
screws provided with the equipment rack to mount the switch on the 19 inch rack.
- 3 -
Model
16FE(PoE)+2G TP/SFP Combo
Standard
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3x, IEEE802.3af, IEEE802.3at
Network Media(Cable)
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e cable (≤100m)
1000BASE-X: MMF or SMF SFP module
MAC Address Table
4K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T/X: 1488095pps/Port
Switching Capacity
7.2G
Dimensions (L*W*H)
440*232*45 mm
Fan
Fan
Power Input
AC: 100~240V, 50/60Hz
PoE Port
Port1~16
PoE Power on RJ45
Mode A 1/2(+),3/6(-)
PoE Power Output
Voltage: 55V DC Power: 32W(Max)
PoE Power budget
300W
Temperature
Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F )
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F )
Humidity
Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing
Turn on the switch
Plug in the negative connector of the provided power cord into the power socket of the device, and the positive connector
into a power outlet . After the device is powered on, it begins the Power-On Self-Test. The PWR LED indicator will light on
all the time.
Specifications
- 4 -
Loading...