Union Rustic W002988761 Owner Manual

HGN782

HAGNEY LANE L-SHAPED DESK

November, 2019

Assembly Instructions - Important:

Carefully unpack and identify each component before attempting to assemble. Refer to parts list. Please take care when

assembling the unit and always set the parts on a clean, soft surface. If you require any assistance with assembly, parts or

information on other products, please visit our website: www.officestar.net or call or write us.

1. Do not use this product unless all screws and bolts are securely tightened.

2. Check that all screws and bolts are tight every three months or as needed.

3. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.

4. Do not use this product as a stepladder.

5. Use this product for its intended purpose only.

6. FOR INDOOR RESIDENTIAL USE ONLY.

LIMITED WARRANTY

OSP Home Furnishings™ warrants to the original purchaser that this product will be free from defects in material and workmanship as
described below. OSP Home Furnishings™ will repair or replace, at its option, without charge to the original purchaser only, defective
products or parts for one (1) year from the date of purchase. Replacement parts can only be supplied if parts are available. Items out of
production may be unavailable. This warranty shall be effective for the applicable time period beginning from the date of purchase as shown
on your original sales receipt. This warranty is your sole remedy for product defects and excludes defects due to or arising in connection
with product abuse or misuse, use modification of, or attachments to the product, and products or parts not used, maintained, or installed
in accordance with the company’s installation, maintenance and/or applicable guidelines. There are no other warranties, express or implied,
other than those specifically described, including without limitation any implied warranty of merchantability or of fitness for a particular purpose.
OSP Home Furnishings™ will not be responsible for incidental or consequential damages. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal
rights and you may also have other rights which may vary from state to state. Our quality standards are among the highest in the industry.
Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our Parts Department will do everything possible
to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free parts number 1-800-
950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time. To make a warranty claim, contact Parts Department. Provide
model number, proof of purchase, description of the problem and obtain return authorization. At its option OSP Home Furnishings™ will:
(a) Supply compatible components of current manufacture. (b) Repair the customer’s component. The customer must prepay freight on any

components returned to the factory. Return freight on components still in warranty will be paid by OSP Home Furnishings™.

(I)

)(

)

PARTS

(A) Left Top Panel (1 PC) (B) Right Top Panel (1 PC)

(C) Left Side Panel (1 PC) (D) Right Side Panel (1 PC)

(E) Right Frame (1 PC) (F) Support (1 PC)

(G) Upper Shelf (1 PC) (H) Lower Shelf (1 PC)

Upper Divider Panel (1 PC

J) Lower Left Divider Panel (1 PC

PARTS

(K) Lower Right Divider Panel (1 PC) (L) Left Rear Panel (1 PC)

(M) Right Rear Panel (1 PC) (N) Drawer Front Panel (1 PC)

(O) Drawer Left Side Panel (1 PC) (P) Drawer Right Side Panel (1 PC)

(Q) Drawer Rear Panel (1 PC) (R) Drawer Bottom Panel (1 PC)

HARDWARE LIST

NO DRAWING DESCRIPTION SIZE QUANTITY

1 Screw 12 PCS + 2 EXTRA

2

3

4

5

6

7

8

Screw

Nail Screw

Screw

Screw

Bolt

Bolt

Cam Screw

#6.5 x 1/2”

#8 x 9/16”

N/A

Ø6 x 30mm

#10 x 1-1/2”

M5 x 12mm

M4 x 22mm

N/A

12 PCS + 2 EXTRA

33 PCS + 2 EXTRA

9 PCS + 1 EXTRA

10 PCS + 1 EXTRA

2 PCS

1 PC

4 PCS + 1 EXTRA

9

10 Cam Screw 2 PCS

11

12

13

14

15

Cam Screw

Small Cam Nut

Large Cam Nut

Wooden Dowel

Wooden Dowel

Left Drawer Rail

N/A

N/A

N/A

N/A

N/A

Ø8 x 40mm

N/A

21 PCS + 2 EXTRA

4 PCS + 1 EXTRA

23 PCS + 2 EXTRA

26 PCS + 2 EXTRA

2 PCS

1 PC

16

17

18

Right Drawer Rail

Left Drawer Slide

Right Drawer Slide

N/A

N/A

N/A

1 PC

1 PC

1 PC

HARDWARE LIST

NO DRAWING DESCRIPTION SIZE QUANTITY

19 Metal Plate 3 PCS

20

21

Phillips screwdriver and hammer also needed for assembly (not provided).

CAM LOCK INSTRUCTIONS

Knob

Sticker

N/A

N/A

N/A

1 PC

5 PCS

180°

STEP 1

(13)

(I)

(H)

STEP 2

(9)

(G)

(13)

(A)

FULLY TIGHTEN ALL CAM SCREWS (9) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 3

(13)

STEP 4

(1)

(K)

(J)

(16)

FULLY TIGHTEN SCREWS (1) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(I)

(5)

FULLY TIGHTEN SCREWS (5) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(G)

STEP 5

(G)

(K)

(J)

STEP 6

(12)

FULLY TIGHTEN CAM NUTS (12) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(K)

(G)

(H)

(5)

(J)

FULLY TIGHTEN SCREWS (5) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 7

(9)

(15)

(D)

(1)

(13)

(C)

STEP 8

(15)

FULLY TIGHTEN SCREWS (1) AND ALL CAM SCREWS (9) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(G)

(C)

(D)

(H)

(12)

FULLY TIGHTEN ALL CAM NUTS (12) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 9

(A)

(12)

STEP 10

FULLY TIGHTEN ALL CAM NUTS (12) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(L)

(3)

FULLY TIGHTEN ALL NAIL SCREWS (3) USING HAMMER (NOT PROVIDED).

STEP 11

(8)

(N)

STEP 12

FULLY TIGHTEN CAM SCREWS (8) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(O)

(N)

(11)

(P)

FULLY TIGHTEN CAM NUTS (11) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 13

(R)

STEP 14

(5)

(Q)

FULLY TIGHTEN SCREWS (5) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 15

(17)

(18)

(1)

(17)

(18)

FULLY TIGHTEN ALL SCREWS (1) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 16

(20)

(7)

FULLY TIGHTEN SCREW (7) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 17

(N)

STEP 18

(M)

(13)

(2)

(19)

FULLY TIGHTEN SCREWS (2) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 19

(E)

(10)

STEP 20

FULLY TIGHTEN CAM SCREWS (10) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(E)

(12)

(M)

FULLY TIGHTEN CAM NUTS (12) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 21

(4)

(9)

(F)

(B)

(4)

(B)

(2)

STEP 22

(19)

FULLY TIGHTEN ALL SCREWS (2 & 4) AND CAM SCREWS (9) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(B)

(E)

(4)

(12)

FULLY TIGHTEN SCREWS

(M)

AND CAM NUTS (12) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

STEP 23

(6)

(F)

STEP 24

FULLY TIGHTEN SCREWS (6) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(14)

(B)

STEP 25

(4)

(2)

STEP 26

FULLY TIGHTEN ALL SCREWS (2 & 4) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).

(21) (21)