Page 1
WARNING!!
Furniture Tipping Risk.
Serious risk of severe or fatal crush injuries can occur from
furniture tipping over if not secured.
Children like to climb on furniture and Unsecured furniture
can pose a serious danger.
Please follow all instructions and install the tip-over
restraints provided.
In addition to installing the restraints, to help prevent tipover:
1. Unless specifically designed to accommodate, do not set
TV’s or other heavy objects on top of this product.
2. Never allow children to climb or hang on top glass.
3. Do not step on the Table base
Page 1 OF 9
Page 2
Label Picture Description QTY
A Drawer Part 1
B Legs 4
Caution : You must read this before you proceed
Bedside
Page 2 OF 9
Page 3
Label Picture Description QTY
① Bolt (M6x16mm) 9
② Washer 9
③ Allen Key 1
4
screwdriver (not provided) 1
5
Hammer (not provided) 1
6
Power Drill (not provided) 1
7
Bracket 4
8
Wall Plug Screw 4
9
Wall Plug 4
10
Cabinet Restraint Strap 2
⑪ Small Screw 4
Page 3 OF 9
Page 4
Before
Beginning
Assembly:
Page 4 OF 9
Page 5
Step 1
With assistance from your adult partner, place the Bed side wooden Part
(A) top down as picture, on clean, non-marring surface.
As shown in “Step 1” picture Affix the Leg (B) to the Drawer part ( A) by
using Allen Bolt (①) , Washer (② (and Allen Key (③) .
Tighten the Bolts fully in a sequential manner.
This Bedside has multiple parts and may require up to some 30 minutes to
assemble. To give you an overview of the Bedside parts, the above picture
is to help you put the various parts into perspective. Please read through
the instructions below to familiarise yourself with the parts and steps before
assembly.
Overview
Drawers part ( A)
Legs ( B)
( A)
②
( B)
①
③
Page 5 OF 9
Page 6
Step 2
Serious or fatal crushing injuries can occur from tipping furniture.
To help prevent tip-over: ALWAYS secure this furniture to the wall
using Cabinet Restraint Device.
See product instructions for more ways to help prevent furniture tip-
over.
Usage For Cabinet Restraint Device:
To secure Bedside against wall, attach two Brackets ⑦ on wall and
product, use Cabinet Restraint Strap ⑩ to connect the Brackets ⑦.
Chest Restraint Device Installation Instructions
Repeat "step 1" to assemble another leg(B) to Badside ( A). Upon
assembly of all the legs, flip the Chest as shown in above picture.
Page 6 OF 9
Page 7
Step4
4.1) Drill two holes on wall at same height as Brackets ⑦ on Chest with
Power Drill⑥.
You can mark these points in two ways as below:
1) Move the Chest back to the wall. Mark two points same height as Chest
on the wall.
Note: The Brackets need to be secured to solid, load bearing surface.
Please use a Stud Finder(not supplied) if needed to locate the Wall
Frame.
2) Measure the height of the Brackets ⑦ with ruler/measuring tape and
mark on
wall to keep them accurate and same height.
4.2) Insert Wall Plugs ⑨ into drilled holes on wall with Hammer ⑤.
Step 3
3.1 - Turn the Bedside so the back faces you.
3.2 - Attach Bracket ⑦ to the back panel using small Screw ⑪ with
ScrewDriver ④.
3.2
3.1
Page 7 OF 9
Page 8
Step 5
Attach Brackets ⑦ to Wall Plugs ⑨ using Wall Plug Screws ⑧ with
Screwdriver ④.
Step 6
Move bed side to the wall.
Pull the Restraint Straps ⑩ through the Brackets ⑦ on the wall and
Bedside one by one, and pull the Restraint Straps ⑩ tight.
This Bedside is now ready to use.
Caution: This Bedside can only be used on flat, level surface.
8
8
9
9
7
7
10
7
Page 8 OF 9
Page 9
Page 9 OF 9
Loading...