Assembly Instruction
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters,wire strippers,electricaltape, safetyglasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifany partsare missingordamaged, donot attempttoassemble, install,or operatethefixture. Contactcustomer serviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(15)B10Candelabra Basebulbs 60WMaximumor
(15)CandelabraBase T8Vintage bulbsare recommendedbutnot supplied.
20-30minutes
Identifyandinspect allparts beforebeginninginstallation. Checkpackage contentlistand diagramsbelow toensureall partsare
Package Contents
Medium
Tier
x1
Upper Tier
C
x1
B
Fixture Loop
with Side Rods
A
x1
STEP 1 Install Fixture Loop with Side Rods, Upper Tier, Medium
Tier and Bottom Tier together
A. Attach side rods on the Bottom Tier (D) and side rods on the Top Tier
B. Carefully pull supply wires and ground wire through the Fixture Loop
-
(B) to the loops in the Medium Rod (C).
with Side Rods (A) and attach side rods of Fixture Loop with Side
Rods (A) to loops in the Upper Tier (B).
B
Loop
D
C
Supply Wires and
Ground Wire
A
TOP VIEW
Figure 1
Side Rod
AA
Crossbar
Assembly
x1
Bottom Tier
D
x1
BB
Quick Link
CC
x2
Hardware Contents
Fixture Chain
x1
Ceiling
DD
Canopy
x1
1of3
B
Side Rod
C
Side Rod
D
Loop
Loop
STEP 2 - Install the CrossbarAssembly to Outlet Box andAdjust
the length of the Nipple
A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
.
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the canopy lock ring from the canopy chain loop. Place the
Ceiling Canopy (DD) over the canopy chain loop against the ceiling
to determine the correct position of the nipple. Thread the canopy
lock ring onto the canopy chain loop.Adjust the nipple to allow the
Ceiling Canopy (DD) to rest against the ceiling when held in place by
the canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
STEP 4 - Making the Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B.
Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
Outlet Box
AA
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Figure 2
Green Ground Screw
Nipple
Canopy Chain Loop
DD
Canopy Lock Ring
STEP 3 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (BB) to your desired length by removing
links if needed. Put a cloth over the Fixture Chain (BB) to protect the
finish.
B. Pull the supply wires through the Fixture Chain (BB) alternating
links. After the wires are through the Fixture Chain (BB), pull the
Supply Wires and the Ground Wire through the canopy lock ring and
the Ceiling Canopy (DD) in order.
C. Attach one end of the Fixture Chain (BB) to the fixture loop with one
Quick Link (CC). Lift the fixture
and Fixture Chain (BB) up and
attach the other end of the Fixture
Chain (BB) onto the canopy chain
loop with another Quick Link (CC).
Nipple
The fixture will now hang safely.
D. Feed the Supply Wires and
Ground Wire through the canopy
chain loop and nipple into the
outlet box. Cut the wires leaving
approximately 8” of wire
Supply Wires
and Ground
Wire
Canopy
Chain Loop
CC
extending from the Outlet Box.
E. Go to Step 4 for wire connections
BB
and follow the directions. Return
to Step F in this step when
complete with Step 4.
F. Raise the Ceiling Canopy (DD)
DD
and canopy lock ring up the
Fixture Chain (BB) and over the
canopy chain loop. Tighten the
Canopy
Lock Ring
canopy lock ring onto the canopy
chain loop until tight.
Suggested chain length for
Ceiling height :
9’ ceiling : use 2 links of chain and
2 quick links
Figure 3
CC
Fixture
Loop
10’ ceiling : use 12 links of chain
and 2 quick links
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
on the Crossbar
White wire from fixture
identified with the Label “N”
Black wire from fixture
identified with the label “L”
Ground wire
from Fixture
Figure 4
STEP 5 - Install Bulbs
A. Insert bulbs onto the sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Socket
T8 Vintage Bulb
(recommended
but not supplied)
Figure 5
2of3
FINISH: MOTTLED BLACK
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
5” Dia.
142.5” OVERALL
HEIGHT INCLUDES
96” CHAIN AND
2 QUICK LINKS()
38.5” Dia.
40.75"
3of3
Loading...