Union Community AC 2100PLUS User Manual

AC-2100 Plus. USER GUIDE

Version ENG-1.00

Copyright 2000 By Union Community Co., LTD.

AC-2100 Plus 사용자 가이드 2

Version

Date

Description

Firmware Version

1.00

2016-12-28

-Initial Release

10.61.00-000.00

<Revison History>

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 3

<Glossaries>

 Administrator (Admin)

- The administrator can access to the terminal menu mode. He/she has the authority to

add/modify/delete terminal users and to change the operating environment by changing
settings.

- If there is no registered administrator in the terminal, anybody can access to the terminal menu

and change settings. It is recommended that more than one administrator will be
necessarily registered in the terminal.

- The administrator has the authority to change critical environmental settings of the fingerprint

reader. So, special attention is required to its registration and operation.

 1:1 Authentication (One-to-one, Verification)

- The user fingerprint is verified after entering User ID or Card.

- Only User ID or the user fingerprint registered to the card is compared. This is called One-to-

One Authentication.

 1:N Authentication (One-to-many, Identification)

- The user is identified only by the fingerprint.

- The same fingerprint as the input fingerprint is identified among the registered fingerprints

without User ID or Card entered. This is called One-to-N Identification.

 Authentication Level

- As a level used for fingerprint authentication, it is displayed in Step 1 to 9. Authentication

cannot be allowed before the degree of match between two fingerprints is higher than the set
authorization level.

- The higher authentication level may ensure the higher security. But it requires the relatively

high concordance rate. So it high likely to deny authentication when trying to authenticate.

- 1:1 Level: Authentication level used for One-to-one authentication

- 1:N Level: Authentication level used for One-to-N authentication

 Authentication Method

- This refers to various types of authentication methods composed of each combination of

FP(Fingerprint) and RF(Card) and so forth.
Ex) Card or FP: Authenticated by either card or fingerprint

 Function Key

- This refers to [F1], [F2], [F3], and [F4] keys, which enable users to access the menu or change

the mode such as Attend or Leave.

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 4

Table of Contents

<Revison History> .................................................................................................... 2

<Glossaries> ............................................................................................................... 3

Table of Contents ........................................................................................................ 4

1. Before Getting Started ............................................................................................. 6

1.1. Safety Notes .................................................................................................... 6

1.2. Product Details ............................................................................................... 7

1.3. Buttons displayed during operation ................................................................. 8

1.4. ViRDI logo LED signals displayed during operation ........................................ 8

1.5. Screens displayed during operation ................................................................. 8

1.5.1. Icon Information ...................................................................................... 9

1.5.2. Message Information ................................................................................ 9

1.6. Voice guide announced during operation ....................................................... 13

1.7. Buzzer guide announced during operation ..................................................... 13

1.8. How to register and enter correct fingerprint ................................................ 13

2. Product Description ............................................................................................... 15

2.1. Product Features........................................................................................... 15

2.2. Configuration Diagram ................................................................................. 17

2.2.1. Standalone Use (Access) ......................................................................... 17

2.2.2. Connecting the PC server (Access, T&A, Food Service Control) ................ 17

2.3. Product Specification .................................................................................... 18

3. Environment Setting .............................................................................................. 19

3.1. Checkpoints before environment setting ........................................................ 19

3.1.1. Enter the menu ...................................................................................... 19

3.1.2. Modify settings ...................................................................................... 20

3.1.3. Save after completion of environment setting ............................................ 20

3.2. Menu Configuration ..................................................................................... 21

3.3. User Management ......................................................................................... 25

3.3.1. Add User ............................................................................................... 25

3.3.2. Delete User ........................................................................................... 28

3.3.3. Modify User .......................................................................................... 29

3.3.4. Add Administrator .................................................................................. 32

3.3.5. Delete All Users ..................................................................................... 32

3.4. Network Setting ............................................................................................ 33

3.4.1. Terminal ID ........................................................................................... 33

3.4.2. IP Setting .............................................................................................. 35

3.4.3. Server IP Setting .................................................................................... 36

3.5. Option Setting ............................................................................................... 40

3.5.1. Application Setting ................................................................................. 40

3.5.2. Authentication Method Setting ................................................................ 45

3.5.3. Door Setting ................................ .......................................................... 49

3.5.4. Volume Setting ...................................................................................... 50

3.5.6. Current Time Setting .............................................................................. 51

3.5.7. RS485 Set ............................................................................................. 53

3.6. Terminal Information Inquiry ....................................................................... 54

3.7. Additional Function (Extra Function) ............................................................ 55

3.7.1. Terminal Lock Setting ............................................................................ 56

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 5

3.7.2. Card Number Inquiry ............................................................................. 56

3.7.3. Monitor Input Port Setting ................................................................ ...... 57

3.7.4. Duress FP Setting ................................................................................... 58

3.8. Device Setting ............................................................................................... 59

3.8.1. System Configuration ............................................................................. 59

3.8.2. Card Reader Format Setting .................................................................... 60

3.8.3. Fingerprint Sensor Setting ....................................................................... 60

3.8.4. Wiegand Speaker Output ........................................................................ 62

3.8.5. Terminal Initialization ............................................................................ 64

3.8.6. External Device Setting .......................................................................... 66

4. How to Use Terminal ............................................................................................. 69

4.1. When operating to [1.Access] ........................................................................ 69

4.1.1. Authentication Mode .............................................................................. 69

4.1.2. Authentication Using Fingerprint ............................................................. 69

4.1.3. Authentication Using Card ...................................................................... 70

4.2. When operating to [2.T&A] .......................................................................... 72

4.2.1. Authentication Mode .............................................................................. 72

4.2.2. Fingerprint Authentication ...................................................................... 72

4.2.3. Authentication Using Card ...................................................................... 72

4.3. When operating to [2.Cafeteria] .................................................................... 72

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 6

Do not operate the terminal
with wet hands, and pay
attention not to let any liquid
such as water enter inside the
terminal.

→ Otherwise, malfunction or
electric shock may be caused.

Keep the terminal away from
inflammables.

→ Otherwise, it may cause a

fire.

Do not disassemble, repair or
remodel the terminal at your
disposal.

→ Otherwise, it may cause

malfunction, electric shock, or
a fire.

Do not allow children to
touch the terminal carelessly.

→ Otherwise, it may cause

safety accidents of children
or malfunction.

Do not install the terminal in a
place exposed to direct
sunlight.

→ Otherwise, it may cause

malfunction, deformation and
discoloration.

Do not install the terminal in
humid or dusty places.

→ Otherwise, it may cause

malfunction.

Do not clean this terminal by
sprinkling water, nor wipe it
with benzene, thinner, and
alcohol.

→ Otherwise, it may cause

electric shock or a fire.

Keep the terminal away from
magnets.
→ Otherwise, it may cause
failure and malfunction.

Keep the fingerprint input
section clean.

→ Otherwise, the fingerprint

cannot be recognized correctly.

Do not spray insecticides or
inflammables on the
terminal.

→ Otherwise, it may cause

deformation and
discoloration.

Keep the terminal away from
shock or sharp objects.

→ Otherwise, it may damage

the terminal and result in
malfunction.

Do not install the terminal in
a place where there is a
severe change in
temperature.

→ Otherwise, it may cause

malfunction.

1. Before Getting Started

1.1. Safety Notes

 Warning

- Non-compliance of safety notes may cause death or serious injury for users.

 Cautions

- Non-compliance of safety notes may cause personal injury or property damage for users.

※ We are not responsible for any accidents and damage that may arise from non-compliance of

the information in this manual.

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 7

1.77inch TFT LCD
(128*160)

Touch Key

Status LED

FP Sensor

Smart Card

1.2. Product Details

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 8

F1

- Switch to ‘Attend’ mode from the default screen.

- Used to move up or increase [↑] in the menu mode

F2

- Switch to ‘Leave’ mode from the default screen.

- Used to move down or decrease [↓] in the menu mode.

F3

- Switch to ‘Outdoor’ mode from the default screen.

- When pressing for more than 2 seconds, you enter the menu mode:

[F3~]

- Used to escape [ESC] or move left [] in the menu mode.

When pressing for more than two seconds, this is used to [ESC] button:
[ESC~]

F4

- Switch to ‘Return’ mode from the default screen.

Pressing it again in the ‘Return’ mode is changed to ‘Access’ mode.

- Used to enter [ENT] or move right [] in the menu mode.

When pressing for more than two seconds, this is used to [ENT] button:
[F4~]

ViRDI

Power

Blue

On: Normal
Flickering: Under Bluetooth communication

ViRDI

Door

Green

On: Door Open
Off: Door Close

ViRDI

Alarm

Red

Off: Normal
Flickering: Case Open or Lock Controller Communication
Error

Displays the current time

- When access control: Displays access mode (F1, F2, F3, F4,
Access)

- When T&A control: Displays Attend/Leave mode (Attend,
Leave, Outdoor, Return)

- When food service control: Displays the menu and current
meal time countdown

Displays Status icon and Access mode

1.3. Buttons displayed during operation

1.4. ViRDI logo LED signals displayed during operation

※ The LED may light on simultaneously in some cases. (Ex. Red and Blue flicker)

1.5. Screens displayed during operation

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 9

① Fire Detection

A fire is detected by the fire detection sensor.

② Door Status

Doors open state (forced open door or open the door when
leaving).

③ Server

Connection
Status

The LAN cable is not connected.

Only Link is connected.

④ USB

Connection

The USB is connected.

- The default screen of AC2100

- The fingerprint is being input or on standby.

- When authentication is successful

1.5.1. Icon Information

1.5.2. Message Information

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 10

- When authentication fails

- When fingerprint input fails

- If your finger is released too early before your fingerprint is

entered

- When an unregistered card is swiped

- When 1:N Authentication is attempted under the condition that

authentication priority is SN and there is no user who has been
allowed for 1:N Authentication

- When anti-passback is in error

- When the server cannot handle too many authentication requests

from the terminal

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 11

- When the terminal is set to the food service control and users

attempt more than two times authentication in the same food time
zone

- When there is no response from the server during authentication

attempt

- When the network is disconnected during authentication attempt

to the server

- The card input is on standby.

- When the card is registered but its authentication is not attempted

in the access control time

- When the terminal waits for a response after requesting

authentication to the server,

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 12

- When the terminal is locked

- When the food service control is set in the non-meal time

- When the terminal program is upgraded

(Do not power off the terminal when this message is displayed.)

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 13

Item

Voice Guide

When the fingerprint is entered

Please enter your fingerprint.

When authentication is successful

You are authorized.

When authentication fails

Please try again.

Ppik

When button or
card is operated

- If the button is pressed or if the terminal reads the card

- If your finger may be released because your fingerprint has
been successfully entered

Ppibik

When failure

If authentication fails or the user’s input is wrong

Ppiriririk

When input
standby

When it is notified that fingerprint input is on standby

Ppiririk

When success

If authentication is successful or if the current user finishes
settings

1.6. Voice guide announced during operation

1.7. Buzzer guide announced during operation

1.8. How to register and enter correct fingerprint

 Correct fingerprint input method

Enter your fingerprint as if you take a thumbprint by using your forefinger if possible.
The fingerprint cannot be correctly registered and entered only by your fingertips.
The center of the fingerprint should be touched with the fingerprint input section.

 Enter the fingerprint of your forefinger if possible.

When using your forefinger, you can enter your fingerprint correctly and safely.

 Make sure that the fingerprint is unclear or wounded.

Too dry, wet, blurry or wounded fingerprints are difficult to recognize. In this case, the
fingerprint of another finger should be registered.

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 14

 Precautions subject to your fingerprint status

The availability of the fingerprint may vary subject to your fingerprint status.
 This product consists of a fingerprint recognition system and cannot recognize the

damaged or unclear fingerprints. They should be registered using a password.

 If your hands are dry, you can blow your breath on the system to operate it more

smoothly.

 For children, too small or unclear fingerprints may be difficult or impossible to use.

They need to register a new fingerprint every six months.

 For seniors, the fingerprint with too many lines may not be registered.
 It is recommended that you will register more than two fingerprints if possible.

 In order to increase the fingerprint authentication rate, it is recommended to use six of

the ten fingers as illustrated above. (Both thumbs, forefingers, middle fingers)

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 15

2. Product Description

2.1. Product Features

 Access control system using the network (LAN)

- The fingerprint reader communicates with the authentication server using a UTP cable and

TCP/IP protocol. This terminal can be applied to the existing LAN network and has easy
expandability. It ensures a fast speed by 10/100 Mbps Auto Detect and facilitates
management and monitoring via the network.

 Convenient Auto Sensing function

- The authentication function can be simply operated by entering the fingerprint without

separate keys entered.

 Easy to verify your ID via fingerprint

- The use of the fingerprint recognition technology (Biometrics) can prevent forgetting your

password, losing your card or key, or avoid the risk of their theft. The use of personal
fingerprints enhances the security of authentication.

 Convenient information message using LCD and voice

- The information message is voiced or displayed on the LCD display for each operation to

receive certification so that you can easily input. In particular, thanks to a built-in
backlight for the LCD display, you can easily identify the screen and operate keys in the
dark room. The voice is stored in the memory and it can be changed to a desired voice
from the server.

 Diverse and flexible access control function

- Easy to use it without the risk of rental, counterfeit and loss of your key or card;

- Provide the complete access control function by granting access authority according to

user groups;

- Provide the flexibility of access control by allowing the access time restrictedly;

- Economical maintenance and development costs compared to other access control devices;

- Remove the inconvenience that visitors are registered in the management office and then

separate cards are issued.

 Diverse utilization for operating systems such as security, access, T&A, and food service

- Various operating methods can be supported depending on how the terminal menu is set.

 Large processing capacity of server

- When the entrant information is managed using the server, it can be processed almost

infinitely.

 Provide the Printer Interlock function

- Provide the output function for the authentication information through the printer

at every time you authenticate.

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 16

FP

Fingerprint Registration
Fingerprint Authentication

Card

Card Registration
Card Authentication

Card or FP

Card or Fingerprint Registration
Card or Fingerprint Registration

Card and FP

Card and Fingerprint Registration
Card Authentication and then Fingerprint Authentication

 Various registration and authentication methods

There are a total of four registration and authentication methods for general users. Before
registering users or administrators, you should determine how to register and authenticate.

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 17

DC12V Adapter

전기정

(Lock+, Lock-, Monitor)

TCP/IP

Internet /
WAN / LAN

TCP/IP

TCP/IP

TCP/IP

TCP/IP

TCP/IP

Food Service Control

Program

Attendance Control

Program

Fingerprint Authentication
Server (Static IP)
UDB Sever
Database (MDB or MSSQL)

Remote Administrator
Program
(User and Terminal Setting
Management)

2.2. Configuration Diagram

2.2.1. Standalone Use (Access)

2.2.2. Connecting the PC server (Access, T&A, Food Service Control)

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 18

구 분

SPEC

REMARK

CPU

32 bits RISC CPU(400MHz)

MEMORY

64M SDRAM

32M NOR FLASH

128M NAND FLASH

1,500 User

1,500 Finger

10,000 Log

Fingerprint Sensor

Optical

Authentication Speed

Less than 1 second

Scan Area / Resolution

12.6 * 14.8mm / 500 DPI

FRR / FAR

0.1% / 0.0001%

Communication Port

TCP/IP

Authentication

Server

Communication

RS-232

Printer

RS-485

External Device
Communication

Wiegand In/Out

Card Reader or
External Device
Communication

Temperature /

Humidity

-20 ~ 60 /

Lower than 90% RH

LCD

1.77’’ Color LCD

SIZE

58mm(W) * 191mm(H) * 62mm(D)

AC / DC Adapter

INPUT : Universal AC 100 ~ 250V

OUTPUT : DC 12V
(Option : DC 24V)

UL, CSA, CE Approved

Card Reader

Smart Card Reader

14443A type,

13.56MHz

2.3. Product Specification

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 19

Select the menu you want to change using

[↑](F1) and [↓](F2) buttons, and press [ENT]

(F4) button to go to the submenu.

3. Environment Setting

3.1. Checkpoints before environment setting

3.1.1. Enter the menu

When pressing [F3] button for more than 2 seconds, the administrator authentication screen
will be displayed.

The administrator is verified by either card or fingerprint depending on the authentication
method. Upon successful authentication, the screen goes to the following menu.

The description of function buttons such as F1, F2, F3, and F4 is in numerical order on the
bottom of the screen as shown above. Go up and down the screen, you can press [ENT](F4)
button to select the desired menu, or press [ESC] (F3) for more than 2 seconds to return to the
upper menu.

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 20

Select [Yes] button to save modifications, [No]
button to cancel modifications, and then press
[ENT] button. If there is any modified information,
the terminal will be rebooted.

※ The administrator authentication menus is displayed only when there is any registered

administrator. Once it is authenticated to enter the menu mode, you can access to all

menus until you escape completely from the main menu.

3.1.2. Modify settings

Modify the existing settings by pressing [↑][↓] buttons.
If the set value is greater than or equal to 2 digits, press [←][→] buttons to move to the digit
you want to change, and press [↑][↓] buttons to change the value up or down.

Press [ENT] button to check the set value or go to next setting.

If you want to cancel during the setting and move to the upper menu, press [ESC] button for
more than 2 seconds.

If only [←][↑][↓][→] buttons are displayed except [ESC] and [ENT] buttons, [ESC] is enabled

by pressing [F3] for more than 2 seconds, and [ENT] by pressing [F4] for more than 2 seconds.

3.1.3. Save after completion of environment setting

After changing settings, press [ESC] button on the main menu screen to save the changes, and
the following screen will be displayed.

 If there is no change information, the screen exits from the environment setting menu

without the “Save?” process.

 If no data is input in the main menu for a certain time during changing environment setting,

the screen will exit from the environment setting menu. In this case, if there is any change

in the menu, the screen performs the “Save?” process. If there is no change in the menu,

the screen goes to the main screen without saving changes.

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 21

1. User

1. Add User

2. Delete

3. Modify

4. Add admin

5. Delete All

2. Network

1. Terminal ID

<Terminal ID>
<Auth Mode>:NS/SN/NO/SO

2. Terminal Net

<Net Type>
<Terminal IP>
<Subnet Mask>
<Gateway>

3. Server Net

<Server Type>
<Server IP>
<Server Port>

3. Option

1. Application

<WorkMode>

1. Access

2. T&A

3. Cafeteria

When setting to Access
<F1 Time>
<F2 Time>
<F3 Time>
<F4 Time>
<Access Time>
<Multi Fn-Key>
<Use Printer>

When setting to T&A
< Attend>
<Leave >
< Out>
< In>
<Access Time>
<Multi Fn-Key>
<Use Printer>

When setting to Cafeteria
<Breakfast>
<Lunch>
<Dinner>
<Supper>
<Snack>
<No Limit>
<Use Printer>

3.2. Menu Configuration

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 22

2. Verify

<Show User>
<Only Card>
<Use TOC>
<Blocking Time>
<Global Block>
<NetErr TimeOut>

3. Doorlock

<Open Duration>
<Open Alarm>

4. Sound

<Voice>
<Beep>
<Case Open>

5. Time

<Sync Time>
<Calendar>
<System Time>
<Time Display>

6. RS485 Set

<RS485 ID>

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr

AC-2100 Plus 사용자 가이드 23

4. Terminal Info

Version

Firmware version of the terminal

WorkMode

Terminal operating modes (T&A +
security/T&A/food service)

Language

Language setting

Auth Mode

Authentication priority

1:1 Level

Authentication level applied when 1:1
authentication

1:N Level

Authentication level applied when 1:N
authentication

Terminal Id

Terminal ID

Net Type

Network connection methods (Static
IP/DHCP)

Terminal IP

Terminal IP address

Gateway

Terminal gateway address

Subnet Mask

Terminal subnet mask address

Server Type

Network server connection mode
setting

Server IP

IP address of the network server
connected to the terminal

Server Port

Port number of the network server
program

MAC Address

Terminal MAC address

Card Ver

Card reader module firmware version

Card Format

Card data display format

All User

The total number of users registered
in the terminal, including
administrators

All Admin

The number of administrators
registered in the terminal

Max User

The maximum number of users who
can be registered in the terminal

All FP

The total number of fingerprints
saved in the terminal

Max FP

The maximum number of fingerprints
that can be registered in the terminal

All Log

The number of the authentication
results saved in the terminal

Max Log

The maximum number of the
authentication results that can be
saved in the terminal

Serial Num

Serial number notation

UNIONCOMMUNITY Co., Ltd. / 12F, Daemyung Valeon, 127, Beobwon-ro,
Songpa-gu, Seoul, 05836, Republic of Korea
TEL: [phone] / FAX: [phone] E-Mail :[e-mail]
http://www.unioncomm.co.kr