UNIMO Technology BIT 1, BIT 2 User Manual

BiT-1 and BiT-2 are functionally equivalent!

1. GETTING STARTED

 Main Feature
 Unpacking and Inspection
 Battery and Battery charging
 Installation

2. GETTING TO KNOW YOUR BiT-1, BiT-2
 Buttons and Inputs

3. BASIC FUNCTION
 Power on / off

BiT-1, BiT-2

Contents

 Volume up / down
 Voice calling
 Redial
 Audio-Power-Off

4. MOBILE PHONE CONNECTION

 Mobile pairing
 Answer an Incoming call
 Put on hold call
 Reject an Incoming call
 Hang up call
 Auto-Answer call
 Transfer Audio sound

5. SECOND MOBILE-PHONE CONNECTION

 Second Mobile-phone pairing
 Put the current call on hold, Answer an incoming call
 Hang up the current call, Answer an incoming call
 Put the current call on hold, Reject an incoming call
 Hang up the call

6. MUSIC

 Enter Music Mode
 Exit Music Mode
 Music Play / Stop

페이지 1 / 11

 Fast Forward/ Rewind

1. Bluetooth V 4.1

2. Advanced Noise Control

3. Usable during Charging

4. Dual Pairing with Smartphone/Bluetooth Device

5. Water Resistance

6. Voice Command

7. RESET

 Factory Reset (To initialize all the settings)
 Cold Reset (To restart the stopped unit)
 DFU Reset (To update the newest firmware)

8. CERTIFICATION

9. SUPPORT

 Precaution
 Limited Warranty
 Technical Data
 Home page / contact info

1. GETTING STARTED

Thank you for choosing our ChatterBox BiT-1, BiT-2, Motorcycle Bluetooth Communication System.

(1) Main Feature (BiT-1, BiT-2 are Functionally Equivalent)

(2) Unpacking and Inspection

BiT-1 contents

페이지 2 / 11

 Main Unit with a pre-installed battery
 USB charging Cable and AC Adaptor
 Headset with Microphones for Open and Full face helmets. Velcro

Speaker Disks, Foam Mic-covers, Microphone Velcro



Helmet Mounting Velcro-type-sticker

 Manual and ChatterBox logo sticker

 Main Unit with a pre-installed battery
 USB charging Cable and AC Adaptor
 Headset with Microphones for Open and Full face helmets. Velcro

Speaker Disks, Foam Mic-covers, Microphone Velcro



Helmet Mounting bracket with Cradle, Screws and Allen Wrench

 Manual and ChatterBox logo sticker

BiT-2 contents

(3) Battery Charging

Connect the supplied USB cable into a PC or wall Charger.

(4) Battery

This product has an irreplaceable rechargeable battery inside. Therefore, when using the product, make

sure to adhere to the following:

 Never separate the battery from the product as this may damage the product
 The battery performance may be reduced over time with usage
 In recharging the battery, make sure to use an approved charger provided by the manufacture. Use

of a non-approved charger may cause fire, explosion, leakage, and other hazards may also reduce

the life time or performance of the battery.

 Do not use cigarette chargers other than the included cigarette charger to charge the unit.
 Store the battery at the temperatures of -20°C ~+50°C / -4°F~+122°F. Higher or lower

temperatures may reduce the capacity and life of the battery or may cause temporary non-

operation.

페이지 3 / 11

 Do not use the product in sub-zero temperature, because it may cause serious reduction of the

battery performance.

 If you apply heat to the battery or throw it into fire, it may explode.
 Do not use the product with a damaged battery. It may explode and/or cause accidents.
 Battery life may vary depending on conditions, environmental factors, functions of the product in

use, and devices used with it.

(5) Installation of Headset and Main unit

The Headset comes with both with open and full face microphones. Please choose the one that you

intend to use and plug it in the connector on the cradle. Please keep the microphone that you are not

using in a safe place for future use. All microphones come with sponge cover. For full face helmet, attach

soft Velcro disk to the helmet chin bar and hard Velcro disk to the microphones.

The Headset speakers should already have Velcro on the back casing. Simply apply the soft Velcro disks

on the liner of your helmet. Mound them in the indentation of the helmet padding where your ears

would line up. Please keep in mind that you need to mount the speakers in a location that is directly

next to your ears.

Attach the right speaker (with the longer wire) to the corresponding Velcro disk that you applied on the

helmet liner. Attach the left speaker (with the shorter wire) to the other Velcro disk. For helmets with

speaker pockets, simply insert the speakers in each corresponding pocket. If your helmet has washable

lining that pops out, you can tuck the wires behind that.

페이지 4 / 11