Uniden America UP001R Users Manual

6

Page

To locate the handset (while it’s off the base), press find handset on the base. The handset beeps
for 60 seconds.

Paging is canceled when pressing any key, find handset on the base or return the handset
to the base.

Flash and Call Waiting

If you have “Call waiting” service and a call waiting tone sounds
while you are on a call, press flash to accept the waiting call. There
is a short pause, then you will hear the new caller. To return to the
original caller, press flash again.

NOTE: You must subscribe through your local telephone company to

receive Call Waiting Service.

Storing a Phone Number in Memory

Your cordless phone has 1 Rocket Dial memory location and 10 additional memory
locations for storing important telephone numbers. You can store your most frequent dialed
number in the one-touch Rocket Dial location.

1) Remove the handset from the base.

2) Press mem. The talk/batt low LED flashes.

3) Enter the phone number, up to 20 digits. If a pause is needed
during the dialing sequence, press redial/p to insert a pause.
Each pause counts as a digit and represents a two second delay
in time between digits as they are sent.

4) Press mem again.

To actually store a number in it’s designated location;

5) Press Rocket Dial.

or

5) Press memory location (0-9) on the keypad to store a number.

A tone indicates that the number is stored. If you enter a number in a location that has a
previously stored number it will overwrite the existing number without warning.

NOTES: • The pause button counts as one digit. Pressing redial/p more than once

increases the length of pause between numbers.

• You have 30 seconds after pressing mem to enter the number you wish to store.
Otherwise, the handset will beep rapidly.

• Memory location for the Rocket Dial is independent from the memory location for
Memory Dial.

Dialing a Stored Number

Using the memory location features

1) Press talk, then press mem.

2) Enter the memory location (0-9) on the keypad. The stored number automatically dials.

NOTE: If you select a memory location that does not have a stored number, the handset

will beep rapidly and the phone will not dial.

EXP3240 12/18/2 11:06 AM Page 6

7

One-touch Rocket Dial

Your phone is equipped with “One-touch Rocket Dial” for instant
dialing. It is used to dial the phone number stored in the one-touch
Rocket Dial location (See “Storing a Phone Number in Memory”).

To instantly dial the phone number stored in the one-touch Rocket Dial
location, simply press Rocket Dial. (There is no need to press talk.
The phone will automatically dial). If you press Rocket Dial and a
phone number is not stored in the one-touch Rocket Dial location, the
phone will beep rapidly and will not dial.

Chain Dialing

The memory locations on the handset are not limited to phone numbers. You can also store
a group of numbers (up to 20 digits) that you need to enter once your call connects. This is
referred to as Chain Dialing.

An example of this is a bank account number. Once you have called your bank, and are
prompted to enter the account number, simply press mem and the location number

(0-9)

where

the special number has been stored.
Store your special number in memory as you would store a phone number (Refer to

“Storing a Phone Number in Memory”).

Erasing a Stored Number from Memory

1) Remove the handset from the base unit.

2) Press mem twice.

3) Press Rocket Dial or the memory location (0-9). A tone indicates that the stored number
is erased from memory.

Changing the Digital Security Code

The digital security code is an identification code used to connect the handset and the base
unit. Normally, setting the code is not necessary.

The first time you charge your handset, the security code is automatically set. In the rare
situation that you suspect another cordless telephone is using the same security code, you
can change the code.

1) Remove the handset from the base unit. Press and hold find handset on the base.

2) The handset begins emitting a paging sound. While holding find handset for at least 3
seconds, place the handset in the base unit. The paging sound stops. Leave the
handset in the base for more than 3 seconds. A new random security code is set.

NOTE: If the handset battery pack is completely discharged or the battery pack is removed,

the digital security code will be lost. If this happens, a new security code is set
automatically next time the battery pack is charged.

EXP3240 12/18/2 11:06 AM Page 7