Uniden America UB326 Users manual

BC246T OWNER’S

MANUAL

OWNER’S MANUAL

Precautions

Before you use this scanner , please read and observe the

Precautions

following. IMPORTANT! This scanning radio has been manufactured so that it will

not tune to the radio frequencies assigned by the FCC for cellular telephone usage. The Electronic Communications Privacy Act of 1986, as amended, makes it a federal crime to intentionally intercept cellular or cordless telephone transmissions or to market this radio when altered to receive them. The installation, possession, or use of this scanning radio in a motor vehicle may be prohibited, regulated, or require a permit in certain states, cities, and/ or local jurisdictions. Your local law enforcement officials should be able to provide you with information regarding the laws in your community.

Changes or modifications to this product not expressly approved by Uniden, or operation of this product in any way other than as detailed by this Operating Guide, could void your authority to operate this product.

EARPHONE WARNING! Be sure to use only a monaural earphone with this scan-

ner. You can also use an optional 32W stereo headset. Use of an incorrect earphone or stereo headset might be potentially hazardous to your hearing. The output of the phone jack is monaural, but you will hear it in both headphones of a stereo headset.

Set the volume to a comfortable audio level coming from the speaker before plugging in the monaural earphone or a stereo headset of the proper impedance (32W). Otherwise, you might experience some discomfort or possible hearing damage if the volume suddenly becomes too loud because of the volume control or squelch control setting. This might be particularly true of the type of earphone that is placed in the ear canal.

Precautions

WARNING!

Uniden does not represent this unit to be waterproof. To reduce the risk of fire or electrical shock, do not expose this unit to rain or moisture.

Motorola PRIVACY PLUS

, SMARTNET®, PL®, Private Line®, and

are registered trademarks of

Motorola, Inc.

is a registered trademark of E.F. Johnson Co.

LTR

EDACS

is a registered trademark of M/A-COM

Private Radio Systems, Inc.

Uniden

and Bearcat® are registered trademarks of

Uniden America Corporation.

™

TrunkTracker

, Trunk Tracking™, and Close Call™ are

proprietary trademarks of Uniden America Corporation. Other trademarks used throughout this manual are the

property of their respective holders.

Precautions

Contents

Introduction ............................................................................... 9

Contents

Feature Highlights ................................................................. 11

About This Manual ............................................................. 15

Understanding Scanning ....................................................... 17

Understanding the Scanner’s Memory ............................... 17

What is Scanning? ............................................................. 17

What is Searching? ............................................................ 18

What is CTCSS/DCS? ....................................................... 18

Conventional Scanning ...................................................... 20

What is Trunk Tracking? .................................................... 21

Trunked Scanning .............................................................. 22

Types of Trunking Systems ................................................ 23

Where To Get More Information......................................... 26

Using a Computer to Control Your BC246T........................ 27

Included With Your Scanner .................................................. 28

Setting Up Your Scanner ....................................................... 28

Using Internal Batteries ...................................................... 29

Using Rechargeable Batteries ........................................... 31

Using AC Power ................................................................. 32

Connecting the Antenna ..................................................... 32

Connecting an Earphone/Headphone ................................ 33

Connecting an Extension Speaker ..................................... 33

Attaching the Belt Clip......................................................... 33

Installing the Demo Software ............................................ 34

A Look At The Keypad ....................................................... 35

A Look At The Display......................................................... 38

Basic Operation ..................................................................... 39

Turning On The Scanner and Setting the Squelch ............ 39

Using Menu......................................................................... 39

Using Func ......................................................................... 39

Using the Scroll Control ..................................................... 40

Using the Menu ..................................................................... 41

Programming Radio Systems ................................................ 43

Programming Conventional Systems ................................. 43

Editing an Existing System Name .................................. 44

Entering a New System Name ....................................... 45

Setting the System Quick Key ........................................ 45

Setting System Lockout .................................................. 45

Setting the System Hold Time ........................................ 45

Setting the Channel Delay Time...................................... 46

Setting Data Skip............................................................. 46

Deleting a System ......................................... .................. 46

Copying a System ......................................... .................. 46

Entering/Editing Conventional Channel Groups.............. 46

Editing an Existing Group Name ..................................... 47

Setting a Group Quick Key.............................................. 48

Setting Group Lockout..................................................... 48

Deleting a Group .............................................. ............... 48

Entering/Editing Conventional Channels ........................ 48

Editing the Channel Name .............................................. 49

Setting Channel Priority................................................... 49

Setting Channel Alert....................................................... 49

Deleting a Channel.......................................................... 50

Copying a Channel.......................................................... 50

Contents

Programming Motorola Systems ........................................ 50

Editing a System Name ................................................... 52

Setting the System Quick Key ......................................... 52

Setting System Lockout .................................................. 52

Setting the System Hold Time ......................................... 52

Setting the Channel Delay Time ..................................... 52

Setting ID Scan/Search Mode ......................................... 53

Editing the Fleet Map ...................................................... 53

Setting the Motorola Status Bit ........................................ 53

Setting the End Code ...................................................... 53

Setting I-Call .................................................................... 53

Setting Emergency Alert ................................................. 54

Setting Control Channel-Only Mode ............................... 54

Reviewing Locked-Out Talk Groups .............................. 54

Clearing All Locked-Out Talk Groups ............................. 54

Setting the Attenuator ..................................................... 54

Deleting a System ........................................................... 54

Copying a System ........................................................... 54

Setting System Frequencies ........................................... 55

Entering/Editing Motorola Channel Groups ..................... 55

Editing a Group Name ..................................................... 56

Setting a Group Quick Key .............................................. 56

Setting Group Lockout ..................................................... 56

Deleting a Group ............................................................. 57

Entering/Editing Motorola Channels ................................ 57

Editing the Channel Name .............................................. 58

Setting Channel Alert ...................................................... 58

Setting Channel Lockout ................................................. 58

Deleting a Channel .......................................................... 58

Copying a Channel .......................................................... 58

Programming EDACS Systems .............................. ... ......... 59

Editing a System Name.................................................... 60

Setting the System Quick Key.......................................... 61

Setting System Lockout .................................................. 61

Setting the System Hold Time.......................................... 61

Setting the Channel Delay Time ...................................... 61

Setting ID Scan/Search Mode.......................................... 61

Setting I-Call..................................................................... 61

Setting Emergency Alert .................................................. 61

Setting the EDACS ID Format.......................................... 61

Reviewing Locked-Out Talk Groups ................................ 62

Clearing All Locked-Out Talk Groups............................... 62

Setting the Attenuator ...................................................... 62

Deleting a System......................... ... ................................ 62

Copying a System......................... ................................... 62

Setting System Frequencies............................................ 62

Entering/Editing EDACS Channel Groups....................... 63

Editing a Group Name...................................................... 63

Setting a Group Quick Key............................................... 63

Setting Group Lockout ..................................................... 63

Deleting a Group.............................. ................................ 63

Copying a Group.............................. ................................ 63

Editing the Channel Name............................................... 65

Setting Channel Alert....................................................... 65

Setting Channel Lockout.................................................. 65

Contents

Deleting a Channel ......................................................... 65

Copying a Channel.......................................................... 65

Programming LTR Systems ................................ ............... 66

Editing a System Name................................................... 67

Setting the System Quick Key......................................... 67

Setting System Lockout................................................... 67

Setting the System Hold Time......................................... 67

Setting the Channel Delay Time...................................... 68

Setting ID Scan/Search Mode......................................... 68

Reviewing Locked-Out Talk Groups ................................ 68

Clearing All Locked-Out Talk Groups.............................. 68

Setting the Attenuator...................................................... 68

Deleting a System ......................................... .................. 68

Copying a System ......................................... .................. 68

Setting System Frequencies............................................ 69

Entering/Editing LTR Channel Groups............................ 69

Editing a Group Name..................................................... 70

Setting a Group Quick Key ............................................. 70

Setting Group Lockout .................................................... 70

Deleting a Group ............................................................ 70

Copying a Group ............................................................ 70

Entering/Editing LTR Channels .......................................... 70

Editing the Channel Name .............................................. 71

Setting Channel Alert ...................................................... 71

Setting Channel Lockout ................................................ 71

Deleting a Channel ......................................................... 72

Copying a Channel ......................................................... 72

Using the Backlight ............................................................ 72

Displaying System Information ........................................... 72

Adjusting the Key Beep ...................................................... 73

Locking/Unlocking the Keypad ........................................... 73

Turning Power Save On or Off ........................................... 73

Using the Close Call Feature ................................................ 75

Turning Pager Screen On or Off ........................................... 78

Turning Repeater Find On or Off ........................................... 79

Using Weather Alert (SAME) ................................................. 80

Care and Maintenance .......................................................... 82

Troubleshooting ..................................................................... 84

Specifications ........................................................................ 89

Optional Accessories ............................................................. 92

Appendix ............................................................................... 93

Preset Fleet Maps ............................ .. ................................ 93

User Defined Fleet Maps .................................................. . 95

Quick Start to Programming Your Scanner ........................ 97

Getting Started ............................................................... 97

Conventional Scanning Worksheet Instructions ........... 100

Motorola Trunking Worksheet Instructions ................... 101

LTR Trunking Worksheet Instructions .......................... 103

EDACS Trunking Worksheet Instructions ..................... 104

Conventional Scanning Worksheet .............................. 105

Motorola Trunking Worksheet ...................................... 106

EDACS Trunking Worksheet ........................................ 108

LTR Trunking Worksheet .............................................. 109

Preprogrammed Systems ................................................ 111

One-Year Limited Warranty ................................................. 123

Contents

The FCC Wants You to Know

This scanner has been tested and found to comply with

The FCC Wants You to Know

the limits for a scanning receiver, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This scanner generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this scanner does cause harmful interference to radio or television reception, which can be determined by turning the scanner on and off, you are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the scanner and the receiver

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) this de vice must accept any interference received, including interference that may cause undesired operation.

Scanning Legally

Your scanner covers frequencies used by many different groups, including police and fire departments, ambulance services, government agencies, private companies, amateur radio services, military operations, pager services, and wireline (telephone and telegraph) service prov i ders. It is legal to listen to almost every transmission your scanner can re c e i v e . H o w e v e r, there are some transmissions that you should never intentionally listen to. These include:

• Telephone conversations (cellular, cordless, or other private means of telephone signal transmission)

• Pager transmissions

• Any scrambled or encrypted transmissions

The FCC Wants You to Know

According to the Electronic Communications Privacy Act (ECPA), you are subject to fines and possible imprisonment for intentionally listening to, using, or divulging the contents of such a conversation unless you have the consent of a party to the conversation (unless such activity is otherwise illegal). This scanner has been designed to prevent the reception of cellular telephone transmissions and the decoding of scrambled transmissions. This is done to comply with the legal requirement that scanners be manufactured so they are not easy to mod ify to pick up these transmissions. Do not open your scanner’s case to make any modifications that could allow it to pick up transmissions that are illegal to monitor. Modifying or tampering with your scanner’s internal components or using it in a way other than as described in this manual could invalidate your warranty and void your FCC authorization to operate it.

In some areas, mobile use of this scanner is unlawful or requires a permit. Check the laws in your area. It is also illegal in many areas (and a bad idea everywhere) to interfere with the duties of public safety officials by traveling to the scene of an incident without authorization.

The FCC Wants You to Know

Introduction

Your BC246T scanner is a state-of-the-art scanner radio

Introduction

with TrunkTracking™ and automatic scanning capabilities. You can store frequencies such as police, fire/emergency, marine, air, amateur, and other communications into the scanner. You can carry it with you wherever you go, use it at home as a base unit, or install it in your vehicle as a mobile unit.

You can use the scanner’s rotary tuner to quickly select channels and frequencies, and you can automatically program channels in an available bank using the AutoStore feature.

Use your scanner to monitor:

• 800 MHz trunked public safety systems

• Police and fire departments (including rescue and paramedics)

• NOAA weather transmissions

• Business/Industrial radio

• Utilities

• Marine and amateur (ham radio) bands

• Air band

This table lists the frequency ranges, default frequency step, default mode (AM, FM, or Narrowband FM), and type of transmissions you can hear for each range.

Frequency Range

Step (kHz)

Mode Transmission

(MHz)

25.0-26.960 5 AM Citizens Band/ Business Band

26.965-

27.405

27.410-

27.995

28.0-29.690 10 FM 10 Meter

29.7-49.990 10 FM VHF Low Band

5 AM Citizens Band Class D

5 AM Business Band

Amateur Band

Introduction

50.0-54.0 10 FM 6 Meter Amateur Band

108.0-

136.9750

137.0-

143.995

144.0-

147.995

148.0-

161.995

162.0-174.0 12.5 FM Federal

216.0-

224.9950

400.0-

405.9875

406.0-

419.9875

420.0-

449.9875

450.0-

469.9875

470.0-512.0 12.5 NFM UHF TV Band

806.0-

823.9875

849.0125-

868.9875

894.0125-

956.0000

1240.0000-

1300.0000

25 AM Aircraft Band

5 FM Military Band

5 FM 2 Meter

Amateur Band

5 FM VHF High Band

Government

5 FM 1.25 Meter Amateur

Band

12.5 NFM Unknown

12.5 NFM Federal Land Mobile

12.5 NFM 70cm Amateur Band

12.5 NFM UHF Standard Band

12.5 NFM Public Service “800” Band

12.5 NFM 25 cm Amateur Band

Introduction

Feature Highlights

General

Feature Highlights

Close Call RF Capture Technology - you can set the

scanner so it detects and provides information about nearby radio transmissions. See “Using the Close Call Feature” on Page 75 for more information.

Dynamically Allocated Channel Memory - your scanner’s memory is organized so that it more closely matches how radio systems actually work, mak i n g it eas i e r t o p r o gram and use your scanner and determine how much memory you have used and how much you have left.

Preprogrammed Systems - your scanner is preprogrammed with over 400 channels covering police, fire, and ambulance operations in the 25 most populated counties in the US. A complete list of the scanner’ s preprogrammed systems is in “Preprogrammed Systems” on Page 112.

Quick Keys – You can set the scanner so you can select systems and groups by pressing a single key . This makes it easy to listen to or quickly lock out those systems or groups you don’t want to scan. You can program up to 10 Quick Keys.

Pager Screen – Y ou can set the scanner so it ignores hit s generated by common pager frequencies while using the Close Call feature.

Ten Service Searches - frequencies are preset in separate public safety, news, amateur radio, marine, railroad, air, CB radio, FRS/GMRS, racing, and special banks, to make it easy to find specific transmissions.

Lockout – You can lock out any system, group, frequency, or channel while scanning. If you lock out a system or group, any channels belonging to that system or group are also locked out.

You can lock out up to 200 frequencies. The scanner skips locked-out frequencies while using the Close Call feature or while searching.

Feature Highlights

CTCSS and DCS Squelch Modes – prevent interference from stations not using the mode you select.

Dropout Delay – You can set whether the scanner pauses at the end of a transmission to wait for a reply . Y ou can set the delay time for each system you scan, and while searching and using the Close Call feature.

Attenuator – You can set the scanner’s attenuator to reduce the input strength of strong signals received by the scanner.

Repeater Reverse – You can set the scanner so it switches to the input frequency on a conventional repeater system or trunked system.

Channel Alert – You can set the scanner so it alerts you when there is activity on any channel you specify.

Memory Check – Lets you see at a glance how much total memory is left.

Frequency Step – Lets you select a frequency step (5,

6.25, 7.5, 10, 12.5,15, 25, 50 or 100 kHz) for manual mode and chain search mode. The scanner’s auto step feature lets you set the scanner so it automatically chooses the correct step.

Quick Recall – Lets you quickly select a specific channel by choosing the system, group, and channel.

Scan/Search Delay – You can set the scanner so it remains on a frequency up to 5 seconds after the last transmission to wait for a possible reply.

T ext Tagging – You can name each system, group, channel, talk group ID, custom search range, and SAME group, using up to 16 characters per name.

Unique Data Skip – Allows your scanner to skip unwanted data transmissions and reduces birdies.

Duplicate Frequency Alert – Alerts you if you try to enter a duplicate name or frequency already stored in the scanner.

Feature Highlights

Memory Backup – If power is lost or disconnected, the scanner retains the frequencies you programmed in its memory.

Trunk Tracking Trunk Tracker

analog Motorola, EDACS, EDACS SCAT, and LTR trunked radio systems. The scanner can scan both conventional and trunked systems at the same time.

Control Channel Only Scanning and Searching – If the scanner is set to scan Motorola trunking frequencies, you can set it so it scans using only control channel data. You do not have to program voice channel frequencies into memory in this mode.

During custom search, you can also set the scanner so it stops only on the control channel for a system type you select.

Bands 21 Bands – Includes 21 bands, with Aircraft and 800

MHz. 25 MHz-1300 MHz – Your scanner covers an

extensive frequency range so you can monitor most of the transmissions in your area.

Note: The scanner’s frequency coverage is not continuous and does not include the cellular telephone band.

™

Operation – Follows conversations on

Weather Weather Search – Lets your scanner receive your local

NOAA weather transmission. SAME Weather Alert – Lets your scanner alert you when

a SAME weather alert is transmitted on a NOAA weather channel. The scanner also displays the transmitted SAME code. This helps you quickly find out about severe weather in your area and lets you avoid false alarms.

Feature Highlights

Search Code Search – Lets you quickly search for the CTCSS/

DCS code used during a transmission. Quick Search – Lets you quickly search starting with the

current frequency in a conventional system, and search for trunked ID’s in a trunked system.

Subaudible Tone Search – Lets the scanner search for CTCSS or DCS tones. You can identify up to 50 CTCSS tones and 104 DCS tones.

Auto Store Frequency AutoStore – Automatically stores all active

frequencies within a system you select. Talk Group ID AutoStore – Automatically stores all new

talk group ID’s into a system you select.

Priority Priority Scan – Priority channels let you keep track of

activity on your most important channel(s) while monitoring other channels for transmissions.

Priority Plus – You can set the scanner so it scans only the priority channels you set

Backlight and Power LCD Back Light – Makes the display easy to see in dim

light. Y ou can adjust the back light so it turns on when you press a key, when squelch breaks during a transmission, or manually.

Low Battery Alert – The scanner alerts you if the batteries need to be recharged or replaced.

Battery Save – You can set the scanner so it stops scanning if there are no transmissions. This helps save battery power.

Feature Highlights

Key Controls Key Lock – You can deactivate the scanner’s keys to

help prevent accidentally changing the scanner’s programming.

PC Control and Cloning PC Control – You can transfer programming data to and

from your scanner and your personal computer, and control the scanner using a computer . This helps you find frequencies listed on the Internet and load them into the scanner.

Clone Mode – You can clone all programmed data, including the contents of the scanner’s memory, menu settings, and other parameters from one BC-246T scanner to another BC-246T scanner.

About This Manual

The screen displays used in this manual are representations of what might appear when you use your scanner. Since what you see depends on the frequencies and user ID’s for your area and the settings you select, you might notice some differences between what is in this manual and what appears on your scanner.

How the Scanner’s Controls Are Represented in This Manual

To help you navigate the scanner’s menus, the steps shown in this manual show the displays you see and the keys you press or control you operate to get a desired result.

This example shows you how to use the scanner’s menu to edit an existing system name. It shows you the key to

press ( ) to select a menu option and the option you see (Program System) when you press . It also instructs you to turn the rotary control (shown as

Feature Highlights

to view a series of choices then select one choice (Edit Name).

Edit Name Edit Sys Option Edit Group Delete System Copy System

4JEdit Name JJ System Name

To get the most from this manual, review the contents to become familiar with the basic functions available. If you are new to scanning or trunk tracking, be sure to read “Understanding Scanning” on Page 17 for a quick background on the technology behind the hobby. The first thing you’ll need to do is install batteries in the scanner. Then you need to connect the included antenna to the scanner. See “Setting Up Your Scanner” on Page 28 if you need any help doing this.

J Program System J

Select System or New System J

System name you want to edit J

Entering Text

To enter a letter, turn the scroll control until the character you want appears, To enter a number, press a number key. To enter a decimal point, pres s .

To move the cursor to the left, repeatedly press /4 while holding down Func. To move the cursor to the right,

repeatedly press 6/ while holding down Func. To clear a character, press . To clear all characters,

press 3 times.

Feature Highlights

Understanding Scanning

This section provides you with background on how scan-

Understanding Scanning

ning works. Y ou don’t really need to know all of this to use your scanner, but some background knowledge will help you get the most from your BC246T.

Understanding the Scanner’s Memory

Y our scanner’s memory is organized in an architecture called Dynamic Allocated Channel memory. This type of memory is organized differently and more efficiently than the ban k/c han nel arc hi tect ure used by traditional scanners. Dynamic Allocated design matches how radio systems actually work much more closely, making it easier to program and use your scanner and determine how much memory you have used and how much you have left.

Instead of being organized into separate banks and cha nnels, your scanner’s memory is contained in a pool. You simply use as much memory as you need in the pool to store as many frequencies, talk group ID’s, and alpha tags as you need. No memory space is wasted, and you can tell at a glance how much memory you have used and how much remains.

With a traditional scanner, when you program it to track a trunked system, you must first program the frequencies. Since you can only program one trunking system per bank in a traditional scanner, if there were (for example) 30 frequencies, the remaining 70 or so channels in the bank are not used and therefore wasted. Also, since some trunked systems might have hundreds of talk groups, you would have had to enter those types of systems into multiple banks in order to monitor and track all the ID’s.

What is Scanning?

Unlike standard AM or FM radio stations, most two-way communications do not transmit continuously. Your BC246T scans programmed channels until it finds an active frequency, then stops on that frequency and remains on that channel as long as the transmission

Understanding Scanning

continues. When the transmission ends, the scanning cycle resumes until the scanner receives another transmission.

What is Searching?

The BC246T can search each of its 21 bands and up to 10 bands together to find active frequencies. This is different from scanning because you are sear ching for fr equencies that have not been programmed into the scanner . When you select frequency bands to se arch, the scanner searches for any active frequency within the lower and upper limits you specify. When the scanner finds an active frequency, it stops on that frequency as long as the transmission lasts. If you think the frequency is interesting, you can program it into one of th e ba nk s. If not, you can continue to search.

What is CTCSS/DCS?

Your scanner can monitor systems using a Continuous Tone Control Squelch (CTCSS) and Digital Coded Squelch (DCS) system, which allow squelch to open only when the tone you have programmed with a specific frequency is received along with a transmission.

CTCSS and DCS are subaudible tone signaling systems sometimes referred to as PL (Motorola’s trademarked term for Private Line). CTCSS and DCS are used only for FM signals and are usually associated with both amateur and commercial two-way repeaters. These systems make use of a special subaudible tone that accompanies a transmitted signal.

CTCSS and DCS are used for many purposes. In many cases, CTCSS and DCS are used to restrict access to a commercial repeater, so that only those units, which transmit the correct tone along with their signal can “talk to the repeater.”

CTCSS and DCS are also used in areas that receive interference where there are several stations with output frequencies close to each other. When this occurs, you

Understanding Scanning

might hear multiple communications at the same time. The stations might even interfere with each other to the point where it is impossible to clearly receive any of the stations. A scanner equipped with CTCSS and DCS (like your scanner) can code each received frequency with a specific CTCSS or DCS frequency. Then, when you receive multiple signals, you only hear the transmission with the CTCSS or DCS tone you programmed. If you do not receive the correct tone with a signal, the scanner’s squelch remains closed and you hear nothing.

Local frequency allocation groups set cooperative standards to establish the CTCSS and DCS tone for each transmitter (or repeater).

You can search for the following CTCSS frequencies and DCS codes.

CTCSS Frequencies (Hz)

67.0 69.3 71.9 74.4 77.0 79.7

82.5 85.4 88.5 91.5 94.8 97.4

100.0 103.5 107.2 110.9 114.8 118.8

123.0 127.3 131.8 136.5 141.3 146.2

151.4 156.7 159.8 162.2 165.5 167.9

171.3 173.8 177.3 179.9 183.5 186.2

189.9 192.8 196.6 199.5 203.5 206.5

210.7 218.1 225.7 229.1 233.6 241.8

250.3 254.1

DCS Codes (Octal)

023 025 026 031 032 036 043 047 051 053 054 065 071 072 073 074 114 115 116 122 125 131 132 134 143 145 152 155 156 162 165 172 174 205 212 223 225 226 243 244 245 246 251 252 255 261 263 265 266 271 274 306 311 315 325 331

Understanding Scanning

332 343 346 351 356 364 365 371 411 412 413 423 431 432 445 446 452 454 455 462 464 465 466 503 506 516 523 526 532 546 565 606 612 624 627 631 632 654 662 664 703 712 723 731 732 734 743 754

Conventional Scanning

Conventional scanning is a relatively simple concept. Each group of users in a conventional system is assigned a single frequency (for simplex systems) or two frequencies (for repeater systems). Any time one of them transmits, their transmission always goes out on the same frequency. Up until the late 1980’s this was the primary way that radio systems operated.

Even today, there are many 2-way radio users who operate using a conventional system:

•Aircraft

• Amateur radio

• FRS/GMRS users

• Broadcast AM/FM/TV stations

• Many business radio users

When you want to store a conventional system, all you need to know is the frequencies they operate on. When you are scanning a conventional system, the scanner stops very briefly on each channel to see if there is activity. If there isn’t, the scanner quickly moves to the next channel. If there is, then the scanner pauses on the transmission until it is over.

Simplex Operation

Simplex systems use a single frequency for both transmit and receive. Most radios using this type of operation are limited to line-of-sight operation. This type of radio is frequently used at construction job sites, and with inexpen-

Understanding Scanning

sive consumer radios such as GMRS/FRS radios. The range is typically 1-8 miles, depending upon the terrain and many other factors.

Repeater Operation

Repeater systems use two frequencies: one transmits from the radio to a central repeater; the other transmits from the repeater to other radios in the system. With a repeater-based system, the repeater is located on top of a tall building or on a radio tower that provides great visibility to the area of operation. When a user transmits (on an input frequency), the signal is picked up by the repeater and retransmitted (on an output frequency). The user’s radios always listen for activity on the output frequency and transmit on the input frequency. Since the repeater is located very high, there is a very large line of sight. Typical repeater systems provide coverage out to about a 25-mile radius from the repeater location.

What is Trunk Tracking?

Your BC246T is designed to track the following types of trunking systems.

• Motorola Type I, Type II, Type IIi, hybrid, SMARTNET, and PRIVACYPLUS analog trunking systems, which are extensively used in 800 MHz communication systems.

• LTR trunking systems

• EDACS SCAT trunking systems

• EDACS trunking systems

When tracking these types of systems, you might want to remember these important points:

• Your scanner can track more than one trunking system at a time and scan conventional and trunked systems at the same time.

• The frequencies for many of the 800 MHz public safety systems are listed in the National Public Safety

Understanding Scanning

Trunked System Frequency Guide included with your BC246T scanner.

Conventional scanning is a simple concept. You enter a frequency used by someone you want to monitor into your scanner’s memory. For example, the police in your area might transmit on 460.500 MHz, the fire department on 154.445 MHz, the highway department on 37.900 MHz, etc. So when your scanner stops on a frequency, you usually know who it is, and more importantly, you can stop on a channel and listen to an entire conversation. This type of scanning is easy and fun.

However, as the demand for public communications has increased, many public radio users do not have enough frequencies to meet their needs, creating a serious problem. Trunking radio systems help solve this problem.

Trunked Scanning

While conventional scanning worked great while there were only a few groups wanting to use the frequencies, with the advent of smaller, lower-cost radios more and more agencies and businesses wanted to take advantage of the utility of 2-way radio. As a result, the bands that were used most became full, so new users were not able to take advantage of the technology as quickly as they wanted.

Trunking solved this frequency shortage by allowing multiple groups to use the same set of frequencies in a very efficient way. While each type of trunking system operates a little differently (see the next few sections), they all work on the same basic premise: even in a system with a lot of users, only a few users are ever transmitting at any one time.

Instead of being assigned a frequency, as with conventional systems, each group is assigned a talk group ID. A central computer controls the frequency each group operates on...and this frequency selection is made each time a user transmits. So, while on a conventional

Understanding Scanning

system queries, replies, and follow-ups are all on a single frequency, they could each be on completely different frequencies on a trunked system. This semi-random frequency assignment made monitoring such a system impossible prior to Uniden’s invention of the Trunktracking scanner.

Not only does your BC246T scan channels like a conventional scanner, it actually follows the users of a trunked radio system. Once you know a talk group’s ID, you won’t miss any of the action.

If you are a new scanner enthusiast, you might want to read the first part of this manual and use your scanner in conventional mode before you begin trunk tracking. Understanding scanning fundamentals and terminology will make trunk tracking much easier. If you are already an experienced scanner operator, you might want to go to “Programming Trunked Systems” on Page 42 now.

Types of Trunking Systems

Trunking systems divide a few frequencies among many different users, but the way that each system does this is slightly different. This section describes some of the technical data behind Motorola, EDACS, and LTR trunked radio systems.

Motorola Trunking

While there are different types of Motorola trunking systems, they all use the same basic trunking method. The system consists of one control channel plus one or more voice channels (typically 10, 20, or 30 total channels). When a user presses Push To Talk (PTT) to tran smit, their radio first sends their talk group information to the control channel. The computer then assigns that talk group to a specific voice channel and transmits that data over the control channel. All radios in that talk group switch over to the assigned voice channel and the user can begin speaking. This all typically takes place in about a second...the person transmitting hears a beep from their

Understanding Scanning

radio when the channel is assigned and then it is OK to start talking.

The systems in use are: Motorola Type I – the radios send the radio ID, the fleet

and subfleet talk group ID to the control channel each time they transmit. To program a Type I system, you need to know the system’s fleet map. The most common fleet maps are included at the back of this manual. You can also find fleet map resources on the web.

Motorola Type II – the radios only send the radio ID and radio channel code to the control channel. The central computer keeps a database of radio ID’s and which talk group is assigned to which channel code for each radio,

so with this system the user’s radio sends only about the data as a Type I system with each transmission. Type II systems do not use Fleet-subfleet talk groups; instead they use a 5-digit ID for each talk group.

Type IIi Hybrid — these systems support a mix of both Type I and Type II users. Like Type I systems, you must know the system’s fleet map to ensure proper tracking.

EDACS Trunking

EDACS trunking works in much the same way as Motorola trunking with a couple of major differences. In an EDACS system, each frequency used by the system is assigned a Logical Channel Number (LCN) so that less data needs to be transmitted by the control channel. Also, talk groups are assigned in an Agency-Fleet-Subfleet (AFS) hierarchy. Also, there is one variation of EDACS called SCAT that your BC246T can monitor.

Logical Channel Numbers – each frequency used by the system is assigned an LCN. This information is programmed into each user radio. When a user presses PTT, their radio sends their AFS information to the control channel. The computer then assigns that talk group to a channel and sends the LCN so that all other radios in tha t talk group will switch to the correct channel. To program an EDACS system in your scanner, you will need to know

Understanding Scanning

both the frequencies used by the system and the LCN for each frequency.

Agency-Fleet-Subfleet – talk group ID’s for EDACS systems are assigned in a way that makes it easy to see at a glance the affiliation of the user. Each radio is assigned a 2-digit agency identifier from 00 – 15. For example, 01 might be used by the police, 02 by ambulance service, 03 by the fire department, and so on. Each agency is then subdivided up to 16 times to provide fleet identification, and then 8 more times to identify subfleets.

For example, the complete AFS for the Police Department West District’s dispatch channel might be 01-062. 01 identifies the agency as the police department, 06 identifies the fleet as the West district, and 2 identifies the subfleet as the dispatch channel. While these assignments are somewhat arbitrary and vary from system to system, there are many resources on the web for finding the assignments for most systems. Because of the logical hierarchy of the AFS system, your BC246T lets you assign wildcard ID’s that let you, for example, use only one ID memory to identify all units in either an agency or a fleet.

EDACS SCAT – EDACS SCAT (Single Channel Autonomous Trunking) systems operate on a single channel and alternate control data with analog voice traffic. While your BC246T cannot track ID’s in this system, it can eliminate the control data so that all you hear is the voice transmissions when you monitor this type of system.

LTR Trunking

L TR (Logic T run ked Radio) syste ms are trunking systems used primarily by business or private communications service providers, such as taxicabs, delivery trucks, and repair services. These systems encode all control information as digital subaudible data that accompanies each transmission, so there is no separate control channel. Users on an LTR system are assigned to specific talk groups, which are identified by the radio as six digit numbers.

Understanding Scanning

These numbers are in the form AHHUUU, where: A = Area code (0 or 1) H = Home repeater (01 through 20) U = User ID (000 through 254) When the scanner receives a transmission on a channel

set to the LTR mode, it first decodes the LTR data included with the transmission. In the ID search mode, the scanner stops on the transmission and displays the t alk group ID on the display . In the ID scan mode, the scanner only stops on the transmission if the LTR data matches a talk group ID that you have stored in the bank’s talk group ID list and have not locked out. LTR systems are frequently programmed so that each radio has a unique user ID.

Where To Get More Information

By itself, this manual really only provides part of what you need to know to have fun scanning – how to program and use the scanner. The two included conventional and trunking frequency guides will give you a good head start on the other part of what you need to know – what frequencies have interesting content.

Information On The Internet

The Internet is a great source for current frequencies and information about scanning. Many web sites have lists of frequencies for your area. Y ou can use a se arch engine to find and use them.

Make a list of the agencies you want to listen to, then look up the frequencies and systems used by those agencies. Here are a few useful sites:

• http://www.scannermaster.com * - frequency resources and home of Police Call.

You can also call them at 1 800 SCANNER (hours are from 10:00 a.m. to 5:00 p.m. Eastern Time Monday through Friday).

Understanding Scanning

• http://www.radioreference.com* - the Internet's premier source for user-supported radio system information.

• http://www.bearcat1.com - frequency information from National Communications.

• svartifoss2.fcc.gov/reports/index.cfm frequency information on file with the US Government

* - This web site is not affiliated with Uniden Corporation. To purchase another copy of the conventional or trunking

frequency guide, contact your local dealer or: Uniden Parts Department

(800) 554-3988 (Hours are from 8:00 a.m. to 5:00 p.m.Central Time Monday through Friday.)

For more information about Uniden and our other products, visit http://www.uniden.com.

- conventional

Using a Computer to Control Your BC246T

You can operate your scanner using software and a personal computer and cable (not included). Demo and fullfeatured software are available at http://www.uniden.com.

Understanding Scanning

Included With Your Scanner

Vol

AC Adapter

Scanner

Batteries

Belt Clip

Wrist Strap

Antenna

Owners Manual

National Public Safety

Trunked System

Frequency Guide

If any of these items are missing or damaged, immediately contact your place of purchase or Uniden Customer Service at: (800) 297-1023, 8:00 a.m. to 5:00 p.m., Central, Monday through Friday.

Frequency Guide

Setting Up Your Scanner

Included With Your Scanner

Setting Up Your Scanner

These guidelines will help you install and use your new scanner:

• If your scanner receives interference or electrical noise, move the scanner or its antenna away from the source.

• To improve the scanner’s reception, use an optional external antenna designed for multi-band coverage. (You can purchase this type of antenna at a local electronics store). If the optional antenna has no cable, use 50-70 ohm coaxial cable for lead-in. A mating plug might be necessary for the optional antennas.

• Use an optional mono earphone or mono headset with proper impedance for private listening. Read the precautions on the inside front cover of this Owners Manual.

• Do not use the scanner in high-moisture environments such as the kitchen or bathroom.

• Avoid placing the scanner in direct sunlight or near heating elements or vents.

Using Internal Batteries

You can power your scanner using two alkaline, lithium, or rechargeable (Ni-Cd or Ni-MH) AA batteries.

Setting Up Your Scanner

Before installing batteries, set the switch in the battery compartment to match the type of batteries you will use. Select ALKALINE for non-rechargeable battery types and RECHARGEABLE for rechargeable battery types, including Ni-Cd and Ni-MH. See also “Using Rechargeable Batteries” on Page 31 when you use rechargeable batteries.

1. Remove the battery cover and set the battery switch.

2. Install 2 AA batteries, matching the polarity symbols (+ -).

WARNING!

Set ALKALINE/RECHARGEABLE to RECHARGEABLE for use only with nickel cadmium (Ni-Cd) or

nickel metal hydride (Ni-MH) rechargeable batteries. Never attempt to recharge non-rechargeable batteries. Non-rechargeable batteries can get hot or burst if you try to recharge them.

Setting Up Your Scanner

+ 98 hidden pages

Uniden America UB326 Users manual

Specifications and Main Features

Frequently Asked Questions

User Manual