Uniden America ON4055 User Manual

English

1-5

alert

GMR4055-2CK, GMR4055-2CKHS GMR4060-2CK, GMR4060-2CKHS

• 15 GMRS / 7 FRS Channels

• 7 Weather Channels

• 121 Privacy Codes

• Internal VOX Circuitry

• Up to 40 Mile Range*

• Backlit LCD Display

• Headset Jack

• 10 Selectable Call Tone Alerts

• 2 VOX earbuds (GMR4055-2CKHS and GMR4060-2CKHS)

• Power Boost PTT

• Roger Beep

• 2 Belt Clips

• Battery Charging Cradle

* Range may vary depending on environmental and/or topographical conditions.

1 Antenna 16 tx - Transmitting

2 MicroUSB port and

earbud jack

3 Push to Talk (PTT) 18

4 Boost 19 call - Transmitting

5 Microphone 20 boost - Change transmis-

6 Channel Up/Down 21 vol - Volume level

7 Weather/Monitor 22 vox - VOX is on.

8 Speaker 23 scan - channel scan

9 9A - Flashlight LED

9B - Flashlight button

10 Screen 25 hi/lo - transmitting in hi

11 MENU/Power 26 Privacy Code

12 Volume Up/Down 27 Weather Channel active

13 Call/Lock 28 miniUSB port

14 rx - Receiving 29 Charging Contacts

- Battery Status

PACKAGE CONTENTS

Your package contains two radios, 6 AA rechargeable NiMH batteries (GMR4055 models) or 2 Li-Ion battery packs (GMR4060 models), one charging cradle, one AC adapter with single miniUSB connector cable, two belt clips, and this

• Battery Level Meter

• 3 AA NiMH batteries per radio (GMR4055)

• Lithium Ion battery pack (GMR4060)

• 10 Hours Battery Life

• MicroUSB Charging Port

• Channel Monitor

• Channel Scan

• Vibrate

• NOAA Emergency / Weather Channels with ALERT

• Emergency Strobe

• Weather Resistant (JIS4)

14 18

19 22

17 Vibe - Silent mode on

- Key Lock

sion power from 1.0W to 2.5W.

selected.

feature on.

24 Channel Number

power (1W) or low power (0.5W)

Weather Channel alert

30 Charging LEDs

reference guide. The GMR4055-2CKHS and GMR4060-2CKHS also include two VOX earbuds. To order Uniden accessories, visit our web site at www.uniden.com or call 1-800-554-3988 during regular business hours. Use only Uniden accessories (AC adapter with microUSB plug).

GMRS LICENSE

The radio operates on the General Mobile Radio Service (GMRS) frequencies when using Channels 1-7 and channels 15-22. You must have a GMRS license issued by the Federal Communications Commission to legally use these channels. For licensing information and application forms, visit the FCC online at: www.fcc.gov/wtb/uls or call the FCC hotline at 1-800-418-3676. If you have any questions, you can contact the FCC direct at 1-888225-5322. No license is required for operation on channels 8-14 or operation on any channel in Canada.

INSTALL THE BATTERY

GMR4055 models use NiMH AA rechargeable batteries (included) or 3 AA alkaline non-rechargeable batteries (not included). GMR4060 models use Lithium Ion battery packs.

To install the batteries/battery pack:

1. Unscrew and remove the battery compartment cover.

2. Install the batteries/battery pack into the battery compartment. Be certain to follow the instructions written on the label on the battery pack. Installing the batteries/battery pack incorrectly will prevent the unit from operating.

3. Replace and screw in the battery compartment cover.

BATTERY LEVEL AND

This unit has a battery level meter on the display to indicate the status of the batteries. When the battery in the unit is low, the battery level meter icon battery pack immediately. If you are using alkaline batteries

(GMR4055 models only), you must replace the alkaline batteries in

order to continue using the radio.

LOW BATTERY ALERT

flashes. Recharge the batteries/

CHARGING THE RADIO

If using rechargeable batteries/battery packs, two radios can be charged directly by using the supplied charging cradle. A single radio can charge using the miniUSB port to connect to a USB power source. For fastest charging, turn off the radio before charging.

Warning! To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden accessories specifically designated for this product.

Warning! Do not attempt to recharge Alkaline batteries (GMR4055 models only).

Using the miniUSB Port

1. Connect the included AC adapter with miniUSB connector cable to the radio's miniUSB port. Connect the other end to an outlet that provides USB charging power (NOT to a USB hub).

2. Charge the batteries/battery pack for 16 hours until the battery indicator stops flashing.

Using the Charging Cradle

1. Connect the included AC adapter with USB connector cable to the charging cradle's miniUSB port. Connect the other end to a standard 120V AC wall outlet.

2. Set the charging cradle on the desk or tabletop, and place the radio in the charging cradle with the keypad facing forward.

3. Make sure that the LED illuminates. Charge the battery pack for 16 hours and remove the radio from the charging cradle after the charging cradle LEDs turn off.

Note:

• Use only the supplied battery and AC adapter or approved accessories from Uniden.

• Charge time may vary depending on the battery life remaining.

• Do not attempt to recharge alkaline batteries (GMR4055 models only). Doing so can create a safety hazard or damage the radio.

• The battery must be installed for the unit to operate, even if the unit is also connected to external power.

• If battery power is low, you cannot operate the radio even using external power. Allow the batteries to charge before using. If you try to transmit while power is low, the radio will automatically turn off.

USING EARBUDS

GMR4055-2CKHS and GMR4060-2CKHS come with VOX earbuds. You can use earbuds for more private communications. To use the earbud, lift the rubber cover from over the headset jack, then plug in the earbud.

Important: Your radio is not weather resistant when using

earbuds. After removing an earbud, be sure to fully press the jack

cover into place to restore its weather resistant capability

USING THE RADIO

Turning the Radio On and Adjusting the Volume

1. Press and hold MENU/ to turn the radio ON. Iincrease the

speaker volume by pressing

VOL ▼.

press

2. Press and hold

MENU/ again to turn the radio OFF.

Adjusting the Sound (Key Beeps)

Your radio emits a beep each time one of the keys PTT and CALL/LOCK) is pressed. and hold CALL/LOCK while turning ON the radio. Repeat to turn the sound back ON.

Choosing a Channel

Your radio has 22 channels and 121 Privacy codes you can use to talk to others. In order to speak to someone, each of you must be set to the same channel and Privacy code.

With the radio in "Normal" operating mode, press the CH ▲/CH ▼ key to increase or decrease the channel number displayed.

Note: Channels 1-7 have a typical range of up to 40 miles. Channels 8-14 have a typical maximum range of up to 5 miles. Channels 15-22 have a typical range of up to 40 miles. You can see which GMRS or FRS channel is active by the icon. The icon is displayed while on GMRS channels, and the displayed while on FRS channels.

Talking on Your Radio

To talk to others using the radio:

1. Press and hold the PTT button and speak in a clear, normal voice

about 2-3 inches away from the microphone. While you are transmitting, the off the first part of your transmission, pause slightly after pressing

PTT button before you start talking.

the

2. When you have finished speaking, release the can now receive incoming calls. While receiving,

Monitor Mode Feature

Your radio allows you to listen for weak signals on the current channel at the press of a key.

To turn ON Monitor mode:

Press and hold WX/MON for 2 seconds until two beeps sound. The receiver circuit stays open, and both noise and weak signals can be heard. The icon stops blinking and disappears.

To turn OFF Monitor mode:

Press and hold WX/MON for 2 seconds to return to "Normal" mode; two beeps sound and the disappears.

Advanced Functions (Menus)

Use MENU/ to access your radio's advanced functions.

Sub Code

Normal

1. Press MENU/ to enter the menus.

2. Additional presses of until exiting to "Normal" operating mode (a double beep sounds).

You can also press any key except

VOL ▼

Privacy Code

Each of the channels 1-22 may have a Privacy code (oF or 1-121) selected. Code oF (OFF) indicates no Privacy code selected and your radio can receive a signal regardless of the code settings of the transmitting radio.

1. Press MENU/ to enter Menu mode. The Privacy code indicator flashes.

2. Press code number displayed. You can also select

stage.

3. Press

4. Press any key other than press

Scan

Your radio has a channel scan feature that allows you to easily scan all 22 channels. When an active channel is detected, the radio pauses on that channel until the channel is clear. Then, after a 2 second delay, the radio continues scanning. Pressing the PTT button while the scan is paused on a channel allows you to transmit on that channel.

Scan

OFF, 1-121

ON/OFF

or tap PTT to exit Menu mode.

CH ▲/ CH ▼

MENU/ to exit Menu mode.

PTT and the radio returns to Idle mode in 10 seconds.

VOL ▲. To decrease the volume,

(except for the

To turn this sound OFF, press

lo icon is

icon appears on the display. To avoid cutting

PTT button. You

displays.

icon stops blinking and

Call

Silent

ON/OFF

MENU/ advance you through the menus

key to increase or decrease the Privacy

VOX Level

OFF,

CH ▲ / CH ▼

CH ▲ /CH ▼

Alert

Tone

ON/OFF

1-10

VOL ▲/

oF (OFF) at this

VOL ▲/VOL ▼

To turn ON channel scan:

1. Press MENU/ repeatedly until the scan... icon and oF blink.

2. Press to start it.

CH ▲ / CH ▼ t

o select Scan mode and press MENU/

To turn OFF channel scan:

1. Press MENU/ with the scan setting of oF.

2. Press any key other than

or Flashlight to turn channel scan off in 10 seconds.

CH ▲ / CH ▼, VOL ▲/VOL ▼,

Voice Operated Transmission

Your radio is equipped with a user selectable Voice Operated Transmitter (VOX) that can be used for automatic voice transmissions. The VOX feature is designed to be used with a headset with a microphone. Transmission is initiated by speaking into the microphone instead of pressing PTT.

To select VOX level:

1. Press MENU/ repeatedly until the vox icon and the VOX

sensitivity level

2. Press

level 1 to increase environments activation in very noisy environments.

(oF,

1-5

) blink

CH ▲ / CH ▼

sensitivity to voice in normally quiet

, and use a higher level to reduce undesired

to change the VOX sensitivity levels. Use

Call Tone

Your radio is equipped with 10 selectable call tones that are transmitted when CALL/LOCK is pressed.

To select a call tone:

1. Press MENU/ repeatedly until the CALL icon and Call Tone

start to blink on the display.

CH ▲/ CH ▲

2. Press

Each tone will be heard through the speaker but will not be transmitted. Cycle through these tones and stay on the tone you want to select.

3. Exit Call Tone to set the selected tone.

to move through the available call tones.

Setting Silent Mode

When you turn on Silent mode, all incoming calls are muted; if you receive a call, the unit vibrates and the backlight flashes. If you do not respond to the call within 15 seconds, the backlight turns off. The radio will also vibrate to remind you that you missed a call. Silent mode is disabled for 15 seconds when you transmit, receive, or press any other button.

Press MENU/

repeatedly until vibe and the current setting start

to blink on the display.

To turn ON Silent mode:

1. Press

CH ▲

2. To exit the Menu, press the

to turn Silent mode on; on displays.

the Menu until exiting to "Normal" mode.

MENU/ key to advance through

vibe appears.

To turn OFF Silent mode:

1. Press

CH ▼

2. To exit the Menu, press the

to display oF.

the Menu until exiting to "Normal" mode.

MENU/ key to advance through

vibe disappears.

Note: To prevent unwanted silent alerts, be sure to use a Privacy

code whenever you use the Silent mode feature. You can hear the received voice when you turn on channel scan and an active channel is detected even during Silent mode.

Normal

Missed Call Alerts

If you receive an incoming call while Silent mode is on and do not respond, the radio will turn on the Missed Call icon.

The radio will additionally remind you of a missed call by vibrating every minute after the call for 3 minutes.

Key Lock

To lock the keypad:

Press and hold CALL/LOCK;

displays.

These functions are not affected by Key Lock:

• Volume Adjust • Call Tone Transmission

• PTT Transmission • Boost

• Power Off • Enter Monitor Mode

• Flashlight

To unlock the keypad:

Press and hold CALL/LOCK again;

Automatic Power Save

disappears.

Your radio has a circuit designed to dramatically extend the life of the batteries. If there is 3 seconds,

your radio switches to Power Save mode. The radio is

no transmission or an incoming call within

still able to receive transmissions in this mode.

LCD Backlight

The LCD Backlight automatically turns ON when any key (except the PTT button) is pressed. It stays lit for 10 seconds before turning OFF.

Roger Beep

Roger Beep is a beep sound that that is sent to indicate the end of transmission (both PTT and VOX transmission). Roger Beep can be heard through the speaker when both Roger Beep and Key Beep are set to ON. When Roger Beep is set to ON and Key Beep is set to OFF, Roger Beep will not be heard from the speaker but it will be transmitted to your party. When Roger Beep is set to OFF, Roger Beep will neither be heard nor transmitted.

To change Roger Beep setting:

Press and hold VOL

▲ while turning the radio on and off. If Roger

Beep is ON, it will be turned off; if it is OFF, it will be turned on.

LED Flashlight with SOS

The radio is equipped with an LED flashlight that can also flash an SOS signal during emergencies. Press the Flashlight button to cycle through the options.

• Press - turn on flashlight. (Quick press - turn off flashlight)

• Press and hold - turn on SOS signal.

• From SOS - Press to turn off SOS signal and return to flashlight.

• From flashlight - Press to turn off flashlight.

Note: The flashlight will also work when the radio is off.

USING THE WEATHER RADIO

Your radio can receive weather broadcasts from the NOAA National Weather Service. When in the Weather Radio Alert mode, the system functions as it does in standard mode but also monitors the selected weather channel for alerts when not communicating. While using the Weather Radio, you are not able to receive GMRS communications.

1. To turn on the Weather Radio Broadcast mode, press WX/MON.

2. Press

3. To exit the Weather Radio Broadcast mode, press

icon appears.

The

CH ▲/CH ▼

desired Weather Channel.

icon disappears.

to increase or decrease the number to the

WX/MON. The

Choosing an Emergency/Weather Channel

There are 7 NOAA channel frequencies available and these frequencies are common between the US and Canada. You need to know what frequency is being transmitted in your location.

Press MENU/

repeatedly until the

icon and the current

setting start to blink on the display.

To turn ON Weather Alert:

1. Press

CH ▲

2. To exit the Menu, press the

to display on.

through the Menu until exiting to "Normal" mode. appears.

3. When the unit receives a warning signal, it beeps for 5 seconds. and channel indicator flash.

MENU/ key to advance you

icon

To turn OFF Weather Alert:

1. Press

CH ▼

2. To exit the Menu, press the

the Menu until exiting to "Normal" mode.

• When Weather Alert is activated, the highest priority is given to this function. It checks the weather alert signals every 5 seconds. When the unit finds a warning signal, it switches to the warning receive mode automatically.

• Weather Alert is activated even if Beep Tone is turned off.

to display oF.

MENU/ key advance you through

icon disappears.

NOAA Weather Radio Frequency List

Ch. Frequency (MHz) CH. Frequency (MHz)

1 162.550 5 162.450

2 162.400 6 162.500

3 162.475 7 162.525

4 162.425

SPECIFICATIONS

Channels 15 GMRS/7 FRS/7 Weather

Privacy Codes 121 Sub-Audible Tones

38 CTCSS/83 DCS Codes

Operating Freq.

GMRS/FRS 462.5500 - 467.7125 MHz

WX 162.4000 - 162.5500 MHz

Power Source GMR4055: 3 AA NiMH Batteries or 3

AA Alkaline batteries (not included)

GMR4060: Li-Ion battery back

Range Channels 1 -7: up to 40 miles

Channels 8 - 14: up to 5 miles

Channels 14 - 22: up to 40 miles

FREQUENCY CHART

CH. Freq. Cross-Ref. CH. Freq. Cross-Ref.

1 462.5625 FRS & GMRS 1 12 467.6625 FRS 12

2 462.5875 FRS & GMRS 2 13 467.6875 FRS 13

3 462.6125 FRS & GMRS 3 14 467.7125 FRS 14

4 462.6375 FRS & GMRS 4 15 462.5500 GMRS 11

5 462.6625 FRS & GMRS 5 16 462.5750 GMRS 8

6 462.6875 FRS & GMRS 6 17 462.6000 GMRS 12

7 462.7125 FRS & GMRS 7 18 462.6250 GMRS 9

8 467.5625 FRS 8 19 462.6500 GMRS 13

9 467.5875 FRS 9 20 462.6750 GMRS 10

10 467.6125 FRS 10 21 462.7000 GMRS 14

11 467.6375 FRS 11 22 462.7250 GMRS15

DCS CODE LIST

Tone

No.

39 023 67 174 95 445

40 025 68 205 96 464

41 026 69 223 97 465

42 031 70 226 98 466

43 032 71 243 99 503

44 043 72 244 100 506

45 047 73 245 101 516

46 051 74 251 102 532

47 054 75 261 103 546

48 065 76 263 104 565

49 071 77 265 105 606

50 072 78 271 106 612

51 073 79 306 107 624

52 074 80 311 108 627

53 114 81 315 109 631

54 115 82 331 110 632

55 116 83 343 111 654

56 125 84 346 112 662

57 131 85 351 113 664

58 132 86 364 114 703

59 134 87 365 115 712

60 143 88 371 116 723

61 152 89 411 117 731

62 155 90 412 118 732

63 156 91 413 119 734

64 162 92 423 120 743

65 165 93 431 121 754

66 172 94 432

Octal Code

Tone

No.

Octal Code

Tone

No.

Octal Code

CTCSS Chart (Hz)

Code Freq. Code Freq. Code Freq.

oF OFF 13 103.5 26 162.2

1 67.0 14 107.2 27 167.9

2 71.9 15 110.9 28 173.8

3 74.4 16 114.8 29 179.9

4 77.0 17 118.8 30 186.2

5 79.7 18 123.0 31 192.8

6 82.5 19 127.3 32 203.5

7 85.48 20 131.8 33 210.7

8 88.5 21 136.5 34 218.1

9 91.5 22 141.3 35 225.7

10 94.8 23 146.2 36 233.6

11 97.4 24 151.4 37 241.8

12 100.0 25 156.7 38 250.3

RBRC INFORMATION

As part of our commitment to protect the environment and conserve natural resources, Uniden voluntarily participates in an RBRC®

LI-Ion

industry program to collect and recycle used Ni-MH and Li-Ion batteries within the US.

Please call 1-800-8-BATTERY for information on Ni-MH and Li-Ion battery recycling in your area. (RBRC® is a registered trademark of the Rechargeable Battery Recycling Corporation.)

Care and Safety: To clean the radio, use a soft cloth dampened with water. Do not use cleaners or solvents because they can harm the body of the unit and leak inside, causing permanent damage. Use a dry, lint-free cloth to clean the battery contacts. Do not submerge the unit in water. If the unit gets wet, turn it off and remove the batteries immediately.

Dry the battery compartment with a soft cloth to minimize potential water damage. Leave the battery compartment cover off overnight to ensure complete drying. Do not use the radio until the unit is completely dry.

REGULATORY INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation.

Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Your radio is set up to transmit a regulated signal on an assigned frequency. It is against the law to alter or adjust the settings inside the radio to exceed those limitations. Any adjustments to your radio must be made by qualified technicians.

To be safe and sure:

• Never open your radio’s case.

• Never change or replace anything in your radio except the batteries.

Your radio might cause TV or radio interference even when it is operating properly. To determine whether your radio is causing the interference, turn it off. If the interference goes away, your radio is causing it. Try to eliminate the interference by moving your radio away from the receiver. If you cannot eliminate the interference, the FCC requires that you stop using the radio.

Hazardous Environments: Do not operate the radio in hazardous environments. Explosion or fire may result. Do not operate the radio near unshielded electrical blasting caps.

Under certain conditions, radios can interfere with blasting operations and may cause an explosion. Turn your radio OFF to prevent accidental transmission when in a blasting area or in areas posted: "Turn off two-way radio." Construction crews often use remote control RF devices to set off explosives.

WARNING! Read this information before using the radio. In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters.

Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of the radio complies with the FCC guidelines and these international standards.

Never allow children to operate the radio without adult supervision and the knowledge of the following guidelines.

WARNING! It is up to the user to properly operate this radio transmitter to insure safe operation. Please adhere to the following:

Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for a replacement antenna.

IC INFORMATION

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modifications to this equipment may void compliance with I.C. Rules. Any change or modification must be approved in writing by Uniden. Changes or modifications not approved by Uniden could void the user’s authority to operate the equipment.

L’appareil est conforme aux normes d’Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) Ce dispositif ne doit pas causer d’interférences et (2), il doit pouvoir accepter les interférences, incluant celles pouvant nuire à son fonctionnement normal.

Tous les changements apportés à cet appareil, s’ils ne sont pas expressément approuvés par Uniden ou toute utilisation de celui-ci d’une autre manière que celle décrite dans ce guide peut annuler votre autorisation de le faire fonctionner.

Hand-Held Operation (Held-to-Face)

This device was evaluated for typical hand-held (held-to-face) operations with a 1 inch spacing from the front of the radio. For handheld operation, the radio should be held 1 inch from the user's face in order to comply with FCC RF exposure requirements.

Body-Worn Operation

This device was evaluated for body-worn operations with the supplied belt-clip accessory. (All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines.

For body worn operation, this device has been tested and meets the Industry Canada RF exposure guidelines when used with Uniden accessories supplied or designated for this product. Use of other accessories may not ensure compliance with Industry Canada RF exposure guidelines.

Fonctionnement de l’appareil, lorsque porté sur le corps. Cet appareil a été testé et s’est avéré conforme aux normes d’Industrie Canada et approuvé pour le port sur le corps à l’aide des accessoires Uniden inclus et conçus pour cet appareil. L’utilisation d'accessoires ne respectant pas les exigences d'exposition RF d’Industrie Canada doit être évitée.

ONE-YEAR WARRANTY

IMPORTANT: SAVE YOUR RECEIPT! Evidence of original purchase

is required for warranty service.

WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")

ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.

WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is: (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, sub-

assemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this product.

STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OVERPAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America and Canada.

PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). Disconnect the battery from the Product and separately secure the battery in its own separate packaging within the shipping carton. The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it.The Product should be shipped freight prepaid, by traceable means, to warrantor at:

Uniden America Corporation C/O Saddle Creek 743 Henrietta Creek Road, Suite 100 Roanoke, TX 76262