Uniden UH073sx User Manual

Page 1
To bring outstanding wireless communication products
to people's lives throughout the world.
Operating Guide
uh073sx
Page 2
WARNING!
i
WATERPROOF: JIS7
This Means:
Being defined as having no ingress of water when immersed at 1 metre for 30 minutes. The uh073sx will only meet this rating if fully assembled and all rubber seals and bungs are well maintained and correctly fitted. This means that the speaker microphone bung is inserted, and the battery pack and antenna are attached and securely fastened.
LITHIUM ION BATTERY PACK WARNING
M This equipment contains a Lithium Ion Battery Pack. M The Lithium Ion Battery Pack contained in this equipment may
explode if disposed of in a fire.
M Do not short-circuit the Battery Pack. M Do not charge the Lithium Ion Battery Pack used in this
equipment in any charger other than the one designed to charge this Battery Pack. Using another charger may damage the Battery Pack or cause the Battery Pack to explode.
M Lithium Ion batteries must be disposed of properly.
USER LICENSE INFORMATION
The citizen band radio service is licenced in Australia by ACMA Radio-communications (Citizen Band Radio Stations) Class Licence and in New Zealand by MED General User Licence for Citizen Band Radio and operation is subject to conditions contained in those licenses.
Page 3
CONTENTS
1
Introduction
Features ..................................................................................................2
Included in your Package ........................................................................3
Optional Accessories ............................. .................................................3
Getting Started
Mounting the Drop-in Charger ................................................................4
Attaching the Antenna .............................................................................4
Attaching the Battery Pack ......................................................................5
Attaching the Beltclip ...............................................................................5
Charging the Battery Pack.......................................................................6
Battery Level Display...............................................................................7
Operation
Power On/Off...........................................................................................8
Volume.....................................................................................................8
Adjusting the Key Beeps .........................................................................8
Roger Beep .............................................................................................9
Selecting Channel ...................................................................................9
Squelch..................................................................................................10
To Transmit and Receive ......................................................................11
Using a Repeater Channel ....................................................................12
To Operate uh073sx in Duplex Mode ....................................................13
Scanning................................................................................................13
Open Scan (OS) Mode.....................................................................13
Group Scan (GS) Mode....................................................................14
Programming Scan Channels ..........................................................15
Priority Channel .....................................................................................15
Choosing a Priority Channel.............................................................15
Drop-Out Delay......................................................................................15
Advanced Features ...............................................................................16
CTCSS ............................................................................................16
VOX .................................................................................................16
Power Save ...........................................................................................18
Back Lighting .........................................................................................18
Keypad Lock .........................................................................................18
Busy Channel Lock-out (BCL) ...............................................................19
Monitor ..................................................................................................19
UHF Channel and Frequencies.................................................................20
CTCSS Codes and Frequencies ..............................................................21
Warranty .....................................................................................................22
Controls and Indicators ...........................................................................23
Page 4
2
INTRODUCTION
The uh073sx is a JIS7 Waterproof, portable two-way UHF-CB radio. It is compact, rugged and fits easily in your hand. This hand held UHF radio will give you consistent, outstanding performance in virtually all conditions and situations. To ensure that you get the most from the uh073sx features, please read this operating guide carefully before using the unit.
FEATURES
! 40 UHF CB Channels ! 3W Max TX Power ! 1W/3W Switchable TX Power ! Waterproof (meets JIS7 waterproof specifications) ! Rubber Grips/Seal ! 38 Built-in CTCSS codes ! Backlit Keypad & LCD Display ! Duplex Mode ! Open and Group Scan ! Busy Channel Lockout Function ! VOX Function ! Headset Jack ! Keypad Lock ! Battery Type: Lithium-lon Rechargeable ! Low Battery Alert ! Battery strength Indicator ! Auto Battery Save ! Battery Cover with charge contacts ! Roger Beep
Page 5
3
INCLUDED IN YOUR PACKAGE
Drop-in Charger
(DT073)
Beltclip
Wrist Strap
Lithium Battery
(BP075)
AC Adapter
(AAD-075S)
uh073sx
Antenna
Reference Guide/
Printed Material
Mounting Screws
If any of these items are missing from the box, contact your Uniden Dealer, immediately.
OPTIONAL ACCESSORIES
M VOX Headset M External Speaker Mic
3
U
H0
7 S
X
3
Page 6
4
GETTING STARTED
Attaching the Antenna
Attach the antenna to the uh073sx. Be sure the antenna is firmly seated.
Mounting the Drop-in Charger
1. Mount the drop-in charger to either a table or wall.
Table: Attach the drop-in charger using the mounting screws and washers.
Wall: Insert the two mounting screws into the wall keeping the same space as the holes on the charger.
Place the charger with the screws through the larger holes then turn the charger.
2. Plug one end of the AC adapter into the wall outlet and the other end into the drop-in charger.
When you mount the drop-in charger in a mobile vehicle, use the optional cigarette lead instead.
Page 7
5
Attaching the Battery Pack
1. Place the battery pack onto the back of the radio. It will only fit in one way.
2. Snap the battery release clip until it clicks. Be sure the battery pack fits tightly against the uh073sx body.
Attaching the Beltclip
1. Hold the beltclip in the direction.
2. Apply it to the hanger piece on the back of the radio. Then slide it up.
3. You will hear a click. The beltclip is firmly attached.
Contacts
Avoid exposing the Lithium Ion battery, attached or unattached to the radio, in direct sunshine, heated cars, or in areas with temperatures below –20°C (–4°F) or above +60°C (+140°F). Exposing the chemicals contained within the battery pack to temperatures above +60
°C (+140°F) may cause the battery to
rupture, fail or reduce performance.
In case of exposure to cell contents, wash the affected area thoroughly, and seek medical attention.
Additional battery cautions should be applied as described on page i of your Owner s Manual.
CAUTION!
Page 8
6
! The charger won’t overcharge the battery pack. When charging is completed, the charge LED is no longer illuminated.
! Do not transmit when the uh073sx is in the drop-in charger!
! You can monitor incoming calls while the uh073sx is in the
drop-in charger.
4. To take the beltclip off the radio, turn it
and slid it up.
Charging the Battery Pack
Your radio is powered by a specially designed Lithium Ion battery pack.
! Before operating the uh073sx, charge the Lithium Ion battery pack for 5
hours without interruption in the drop-in charger.
1. Place the uh073sx in the drop-in charger.
2. The red LED illuminates and stays ON, until fully charged.
Page 9
7
Battery Level Display
The BATTERY icon in the top right hand corner of the screen indicates the
uh073sx current battery voltage level at all times. The battery level is displayed in
4 levels.
LEVEL 4 Battery 100% full
LEVEL 3 Battery approx. 40% capacity
LEVEL 2 Low Battery
LEVEL 1 (flashing) Empty Battery
When is pressed at Level Empty, battery icon and channel number will flash, transmission is disabled.
Recharge the battery at any time. From empty the battery will take up to 5 hours to fully charge.
Battery Life : 12 Hours (Typical) This is based on the following Duty Cycle:
Transmit (Low Power) 5%
Receive 5%
Stand-by 90%
PTT
Page 10
8
OPERATION
POWER ON/OFF
To turn the unit ON, rotate the [ON/OFF VOL] clockwise. A channel number and battery level should appear on the display.
To turn the unit
OFF, rotate the [ON/OFF VOL]
knob counter-clockwise. The display will disappear.
ADJUSTING THE KEY BEEPS
Your radio emits a beep each time-one of the keys (except for the PTT or mon) are pressed.
VOLUME
Rotate the [ON/OFF VOL] knob clockwise or counter-clockwise to adjust speaker volume to desired listening level.
See the Controls and Indicators page at the back of this operating guide for button and key operations.
To turn OFF this beep: Press and hold while turning on the radio. To turn ON this beep: Press and hold while turning on the radio.
UH073SX
dup
dup
Page 11
9
ROGER BEEP
Roger Beep is a BEEP that is sent to notify the end of transmission (both PTT and VOX transmission.) Roger Beep can be heard through the speaker when Key Beep is on. Roger Beep is transmitted even if key beep is turned off. However Roger Beep will not be heard from the speaker.
To turn OFF Roger Beep: Press and hold while turning on the radio. To turn ON Roger Beep: Press and hold while turning on the radio.
SELECTING CHANNEL
Press or to select the desired channel.
If you press and hold the or , channel number will scroll rapidly.
Page 12
10
SQUELCH
The squelch is used to eliminate any annoying background noise when there are no signals present.
Think of squelch as a gate. Turn [SQ]
fully clockwise. This raises the "Squelch Gate" so high that only the very strong signals can get through.
Turn [SQ]
fully counter clockwise until you hear a hiss. This opens the "Squelch Gate" so that everything gets through noise, weak signal, and strong signals.
To set the "Squelch Gate" to the desired level, turn [SQ] counter-clockwise until you hear noise. Then turn the [SQ]
clockwise just until the noise stopped. Now only the desired signal can get through.
If an incoming signal is very weak there is a possibility that you will have a choppy or broken reception, due to the sensitivity of the squelch. In this case, simply rotate the [SQ]
clockwise
until the weak signal is heard clearly.
Noise
Weak Signals
Medium Signals
Strong Signals
Make sure to first select a channel not in use before setting the squelch in your
uh073sx UHF-CB radio.
UH073SX
Page 13
11
TO TRANSMIT AND RECEIVE
The uh073sx uses the 40 UHF-CB Channels. For your reference a list of the available channels and corresponding frequencies is printed at the end of this manual.
1. The maximum RF transmit power of
uh073sx is 3 Watts.
2. Before you transmit, listen for activity on the
selected channel.
3. When the channel is clear, press and hold the
to transmit.
TX appears on the LCD.
4. When you have finished speaking, release the
and listen for a response. TX indicator
then disappears on the LCD.
The display shows BUSY when a transmission is being received by your radio.
Hold the radio with microphone approximately five cms in front of your mouth with the antenna at approximately 45* angle away from your head. Speak in a clear, normal conversational voice.
To switch to low power, press . LOW appears on the LCD.
To switch back to higher power, press again. LOW indicator disappears from the LCD.
PTT
PTT
1/3w
1/3w
Page 14
12
USING A REPEATER CHANNEL
UHF CB Repeaters are used to retransmit or relay your signal. Repeaters will extend the range of your radio and overcome the shielding effect caused by solid obstructions.
In normal Simplex operation, your radio transmits on one particular frequency and receives on that same frequency. If there is a barrier (i.e. a Tall Building) that partially blocks your transmitted signal, the possibility of the other radio receiving the signal is very slim. Valleys, metallic structures, etc., tend to act as a screen between radios.
With Duplex operation, the signal coming from your radio is received by the Repeater station and then re-transmitted at the same time on another channel.
Your
uh073sx is designed with duplex capability on Channels 1 to 8. When any of these channels are set to operate in duplex mode during transmission, the uh073sx automatically sends the signal at a frequency 30 channels above the original in order to access the repeater station. After transmitting, the radio reverts back to its original operating frequency.
For example:
1. CH01 is on Duplex Mode
- will receive on CH01 but Transmit on CH31
2. CH02 is on Duplex Mode
- will Receive on CH02 but Transmit on CH32, etc….
Refer to UHF Channel & Frequencies table on page 20.
Standard Operation without the aid of a Repeater Station
Operation with the aid of a Repeater
Normal Simplex Operation Transmitting on CH 01
No signal being received
Repeater Station
CH 31
CH 01
Page 15
13
TO OPERATE uh073sx IN DUPLEX MODE
Eg. CH01 is being used in your area for repeater use.
SCANNING
The uh073sx has two types of scanning; Open Scanning (OS) and Group Scanning (GS).
Scanning allows you to search for active channels programmed in the OS or GS memory.
To initiate scanning;
1. Assuming the unit is on CH17 when switched on.
2. Press and scanning starts. Scan icon flashes during scanning.
Open Scan (OS) Mode (the absence of GS icon indicates that the unit is on OS mode)
Allows continuous scanning of channels stored in the Open Scan (OS) memory. If an active channel is found, scanning will stop on that channel.
The factory has preprogrammed all the 40 UHF channels into the Open Scan channel memory. However, you can change or customize the channels by following the steps on programming Scan Channels on page 15.
Example: CH40 becomes active
If the received signal cease, the unit will wait for at least 3 seconds for the signal to return, otherwise scanning resumes.
To skip the active channel, press momentarily. Scanning resumes.
To deactivate SCAN, press or .
Check with your local retailer for available repeaters.
Press momentarily. The DUP icon appears.
Press again to deactivate the duplex operation. uh073sx will return to simplex operation.
PTT
dup
dup
scan
scan
mem
Page 16
14
Group Scan (GS) Mode
Allows you to monitor a Priority Channel while scanning.
To use GS Mode Scanning, press the key. .
GS icon appears on the
display.
GS Scanning checks the Priority channel activity regularly.
If SCAN is deactivated while in an active channel, the uh073sx will stay on that active channel. If no other channels are active, the uh073sx will reinstate the starting channel.
If SCAN is deactivated while it is turned to an active channel, the uh073sx will stay on that active channel. If none of the channels are active, the uh073sx will reinstate the Priority channel.
If GS Scanning is initiated when there are no channels programmed in GS memory, an error tone will be heard and scanning will not start.
If the Priority channel becomes active the radio will stay on that channel for as long as the signal is present. If the received signal ceases, Priority scanning continues after 3 seconds.
If scanning stops on a channel which is not a Priority Channel the uh073sx will continue monitoring the Priority Channel for activity while listening to the active one.
To deactivate SCAN, press the or .
PTT
os/gs
scan
Page 17
15
Programming Scan Channels
1. Select which Scanning Mode you wish to use OS or GS Mode.
OS is indicated by the absence of the GS icon.
2. Select the channel you want to store by pressing or .
3. Press and hold for 1.5 secs. to store. MEM icon appears and two
short tone beeps are heard.
4. To remove the channels from Memory, press and hold for 1.5 secs.
once more. Two short tone beeps are heard and the
MEM icon disappears.
PRIORITY CHANNEL
The Priority Channel feature allows user to monitor one of 40 channels in the uh073sx, monitoring it every 1.5 secs. during Group Scanning.
Choosing a Priority Channel
DROP-OUT DELAY
While scanning, the uh073sx stops at a busy channel and receives a transmission. When the received signal is over, the unit will wait for 3 seconds for the return of the signal, otherwise, the radio resumes scanning.
The starting channel, when Group Scanning is initiated, is always the Priority Channel. To change the priority channel setting while scanning, (eg. PRI Channel is CH17 (476.825 MHz ));
a. press , to select a higher channel (scanning
pauses).
or
b. press , to select a lower channel.
mem
mem
Page 18
16
ADVANCED FEATURES
VOX
MBuilt-in Voice Activated Circuit (VOX) feature enables the user to
transmit automatically by speaking on the microphone of the VOX headset (not supplied) without pressing the PTT switch.
CTCSS (Continuous Tone Coded Squelch System)
CTCSS is a feature that allows a group to talk to each other without hearing other users on the same channel.
Programming CTCSS Code
1. Select a desired channel to be used with CTCSS.
2. Press and hold for 1.5 secs. CTCSS icon blinks.
3. Press or to select the desired CTCSS code.
4. Press to save the selected code. CTCSS icon stops blinking.
The uh073sx will return to standby mode after 10 secs. of no activity. CTCSS code can be programmed on every channel. There are 38 available CTCSS tone per channel.
CTCSS Scan Operation
1. Press to start scanning (GS or OS) mode.
2. Press and hold to change to CTCSS scan mode.
3. When a signal is sensed on a CTCSS CH, the uh073sx stops for about 400 msecs (decode time) to decode the CTCSS code. If there is no code or the receive code does not match the one programmed on the unit, the unit resumes scanning.
Channels 5 and 35 are used for emergency channels. CTCSS will not operate on these channels.
ctcss
ctcss
ctcss
scan
Page 19
17
VOX feature will not work without the Vox Headset Microphone. The built in mic of uh073sx is temporarily disabled, however accidental pressing of will cause the unit to transmit briefly.
Changing the VOX sensitivity setting to "oF" without removing the microphone will cause the unit to transmit continuously.
To activate VOX
1. Press and hold for 1.5 secs. "VOX" icon blinks.
2. Press either or within 10 secs. to select the desired VOX sensitivity level (9 with the lowest sensitivity to 1 with the highest sensitivity).
3. Press to save the selected level. "VOX" icon stops blinking.
4. Install VOX Headset (not supplied) to uh073sx.
To De-activate VOX
1. Remove VOX Headset from uh073sx.
2. Press and hold for 1.5 secs. until "VOX" blinks.
3. Press repeatedly and until "oF" is displayed.
4. Press to save the setting. "VOX" icon disappears.
PTT
vox
vox
vox
vox
Page 20
18
POWER SAVE
Battery Save feature extends the battery life by switching the receiver circuit power ON and OFF. This feature automatically activates during standby mode (RX mode without signal).
BACK LIGHTING
The Liquid Crystal Display (LCD) and function keys are backlit for easy viewing at night or in low light situations. The back lighting automatically switches ON every time a key (except PTT) is pressed. It turns OFF 5 secs after the last key is pressed.
KEYPAD LOCK
To prevent accidental entries, you can lock the keypad. Press and hold the button until it beeps to activate Key Lock. icon appears.
To unlock the keypad, press and hold the button again. icon disappears.
When the Key Lock is active, a warning beep will be heard if you attempt to press keys. (except for the PTT button)
lock
lock
Page 21
19
BUSY CHANNEL LOCK-OUT (BCL)
This feature prevents accidental transmission on a busy channel. This is recommended on channels where CTCSS is being used. If the channel is "active" and the signal is coming from a non or different CTCSS code user the BCL feature will prevent you from transmitting.
To activate BCL
Press and hold for 1.5 secs. until "BCL" appears on display.
To De-activate BCL
Press and hold for 1.5 secs. until "BCL" disappears from the display.
MONITOR
This feature enables users to listen in for weak signals on the current channel at the press of a button.
To use monitor
! For brief listening, press . ! For continuous listening. Press and hold for 2 sec. A two tone
beep will be heard and the receiver circuit will stay open letting in both the noise & weak signals.
! Display shows MON and BUSY icons. ! To return to normal receive mode press .
bcl
bcl
mon
mon
mon
Page 22
20
UHF CHANNEL & FREQUENCIES
Please follow these guidelines for channel use in Australia:
Channels 05 and 35 are Emergency Channels.
Channel 11 is a Calling Channel.
Channels 22 and 23 are for telemetry and telecommand applications and TX
should be avoided on these channels. General communication is accepted on all other channels with these guidelines:
Channel 40 - road channel (Australia).
Channels 01- 08 (and 31- 38) are repeater channels. Channels 01- 08 (and 31- 38) are repeater channels.
Page 23
21
CTCSS CODES & FREQUENCIES
Page 24
22
WARRANTY
UNIDEN UH073SX UHF CB TRANSCEIVER RADIO
Two Year Limited Warranty
Note: Please keep your sales docket as it provides evidence of warranty. Warrantor: Uniden Australia Pty Limited ABN 58 001 865 498 Uniden New Zealand Limited Warranty only available in original country of purchase Elements of Warranty: Uniden warrants to the original retail owner for the duration of this
warranty, its uh073sx UHF CB Transceiver Radio (hereinafter referred to as the Product) to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. Warranty Duration: This warranty to the original retail owner only, shall terminate and be of no further effect TWO (2) years after the date of original retail sale. This warranty will be deemed invalid if the Product is; (A) Damaged or not maintained as reasonable and necessary, (B) Modified, altered or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) Improperly installed, (D) Repaired by someone other than an authorized Uniden Repair Agent for a defect or malfunction covered by this warranty, (E) Used in conjunction with any equipment or parts or as part of a system not manufactured by Uniden, or (F) Where the Serial Number label of the product has been removed or damaged beyond recognition. Warranty only valid in the country of original retail/sale. Parts Covered: This warranty covers for TWO (2) years, the Product and included accessories. Statement of remedy: In the event that the Product does not conform to this warranty at any time while this warranty is in effect, the warrantor at its discretion, will repair the defect or replace the Product and return it to you without charge for parts or service. This warranty does not provide for reimbursement or payment of incidental or consequential damages. This EXPRESS WARRANTY is in addition to and does not in any way affect your rights under the TRADE PRACTICES ACT 1974 (Cth) (Australia) or the CONSUMER GUARANTEES ACT (New Zealand).
Procedure for obtaining performance of warranty: In the event that the Product does not conform to this warranty, the Product should be shipped or delivered, freight prepaid, with evidence of original purchase, (eg. a copy of the sales docket) to the warrantor at:
UNIDEN AUSTRALIA PTY LIMITED UNIDEN NEW ZEALAND LTD Service Division Service Division 345 Princes Highway, 150 Harris Road, East Tamaki, Rockdale NSW 2216 Auckland Fax (02) 9599 3278 Fax (09) 274 4253 www.uniden.com.au www.uniden.co.nz
Customers in other states should ship or deliver the Product freight pre-paid to the nearest Uniden Authorized Repair Centre. (Contact Uniden for the Warranty Agent nearest you.)
Page 25
23
CONTROLS & INDICATORS
1 Antenna
2 Belt Clip
3 Battery
4 Battery Release Clip
5 PTT (Push to Talk) Key
6 Memory Key (MEM)
7 Scan Button (SCAN)/
Busy Channel Lock-Out Mode (bcl)
8 TX Power/Lock Button
9 Microphone
10 Speaker MIC (Optional) Jack
11 ON/OFF VOL Knob 12 Squelch Knob (SQ)
13 LCD Display
14 Monitor Button (mon)
15 Open Scan/Group Scan
(os/gs)/VOX
16 Channel Up Button ( )
17 Duplex Key (dup)/ CTCSS Key (ctcss)
18 Channel Down Button ( )
19 Speaker
11 12
13 14
10
15 16 17
18
19
6
8
7
9
1
2
3
4
5
UH073SX
1/3w
Page 26
24
LCD Display
A Transmit B 1W Power C Duplex Transmit D Scanning E Monitor F Priority G Busy Channel Lock Out H Group Scanning I Channel Numbers
J CTCSS K VOX L Roger Beep
M Battery Level Indicator N Key Lock O Memory P Receive
GI
K
L
M
NOP
B C D
A
E
F
J
H
Page 27
25
Note:
Page 28
©2007 Uniden Australia Pty Limited/Uniden New Zealand Limited Part Code UTZZ01936ZA(0). Printed in China
Loading...