Uniden UH060SX-2 User Manual
UH060SX-2
Operating Guide
To bring outstanding wireless communication products
to people's lives throughout the world.
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 1
vol/ch
vol/ch
vol/ch
2
CONTROL & INDICATORS
INCLUDED IN YOUR PACKAGE:
• UH060SX Radio (2)
• Operating Guide
• Belt Clip (2)
OPTIONAL ACCESSORIES
• VOX Earset
• Carry Case
1 Antenna
2 PTT (Push-To-Talk) Button
3 Monitor Button
4 Duplex/Call Key
5 Scan Key
6 Channel/Volume/Keylock Key
7 Speaker
8 Headset Jack
9 Volume/Channel up Key
10 Volume/Channel down Key
11 Power On/Off/Select Key
12 Txp/CTCSS Key
13 Microphone
• Charging Cradle with AC Adaptor
• NiMH Battery Pack (2)
• VOX Headset (2)
14 Battery Level Meter
15 Receive Indicator
16 Channel Indicator
17 Scan Indicator
18 VOX Indicator
19 Keypad Lock Indicator
20 Transmit Indicator
21 Volume Setting Indicator
22 HI Indicator
23 LO Indicator
24 CTCSS Indicator
25 Charging LED’s
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 2
3
GETTING STARTED
BATTERY INSTALLATION
Your UH060SX-2 unit uses the included NiMH battery pack for
power. The unit can be powered with optional 4 AAA ALKALINE
batteries.
To avoid damage to the unit do not mix old and
new batteries.
Do not charge alkaline or non rechargeable
batteries.
Uniden does not represent this product to be
waterproof. Do not expose this product to Rain or
Moisture.
If you don't use the UH060SX-2 for long periods,
Uniden recommend removing the batteries. The
UH060SX-2 is designed to retain the previous user
settings. This feature will continue to use a small
amount of battery power while the unit is switched off.
To install the batteries:
1. Make sure your radio is off.
2. Release the battery cover clip, then
remove the battery cover.
3. Insert NiMH battery pack according
to the orientation on the battery
pack.
OR Insert 4 AAA ALKALINE batteries (not
included) according to the polarity
symbols inside the battery
compartment.
4. Align the battery cover tabs with the
UH060SX-2 tab holes then replace
the cover clip.
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 3
4
Place the UH060SX-2 into the charge cradle. The charge light will
come on to indicate the unit is charging. Before operating the
UH060SX-2, charge the battery pack for 16 hours.
If the battery level becomes low, the battery
indicator icon on the display begins flashing.
When the batteries in the unit are low, the unit will go into a
Battery Low mode. The Transmit mode is disabled. Replace the
alkaline batteries immediately or if you are using the NiMH
battery pack, place the radio on the charge cradle to recharge.
Full charge will take up to 16 Hrs.
Do not charge alkaline or non
rechargeable batteries.
BELT CLIP
LOW BATTERY ALERT
To attach the belt clip:
Slide the belt clip until it snaps into place.
To remove the belt clip:
To remove the belt clip, press and hold belt
clip locker, slide the belt clip at the same
time until released.
INSTALLING THE CHARGE CRADLE
• Plug the AC adaptor into the rear of the charge cradle and
into the mains power.
UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 4
Loading...