Uniden UH047sx User Manual

uh047sx

Operating Guide

To bring outstanding wireless communication products

to people's lives throughout the world.

18 19

26 27

TORS

1 Antenna 16 DCS ON Indicator 2 PTT(Push-To-Talk) Key 17 Scan Indicator 3 Monitor Key 18 Memory Indicator 4 Keylock/Call Key 19 Priority Channel Indicator 5 Memory/Scan Key 20 CTCSS ON Indicator 6 Channel/Power Hi-Lo Key 21 Battery Level Indicator 7 Speaker 22 HI Transmit Indicator 8 Headset Jack 23 Lo Transmit Indicator 9 Select/Power On-Off Key 24 CTCSS and DCS Code/Volume Level Indictor 10 Volume/Select Up Key 25 Volume Setting Indicator 11 Volume/Select Down Key 26 VOX Indicator

27 Busy Channel Lockout Indicator

12 Microphone 13 Receive Indicator

28 Keypad Lock Indicator

14 Transmit Indicator

29 Charging LED

15 Channel Indicator

(1)

10 11

CONTROL & INDICATORS

INCLUDED IN YOUR PACKAGE:

• uh047sx Radio • Charging Cradle with AC Adaptor

• Operating Guide • NiMH Battery Pack

• Belt Clip • External Speaker Mic

OPTIONAL ACCESSORIES

• VOX Earset

• Carry Case

• VOX Headset

GETTING STARTED

Uniden does not represent this product to be waterproof. Do not expose this product to Rain or Moisture.

BATTERY INSTALLATION

Your uh047sx unit uses the included NiMH battery pack for power. The unit can be powered with optional 4 AAA ALKALINE batteries.

If you don't use the uh047sx for long periods, Uniden recommend removing the batteries. The uh047sx is designed to retain the previous user settings. This feature will continue to use a small amount of battery power while the unit is switched off.

To avoid damage to the unit do not mix old and new batteries.

To install the batteries:

1. Make sure your radio is off.

2. Release the battery cover clip, then remove the battery cover.

3. Insert NiMH battery pack according to the orientation on the battery pack.

Insert 4 AAA ALKALINE batteries (not included) according to the polarity symbols inside the battery compartment.

4. Align the battery cover tabs with the uh047sx tab holes then replace the cover clip.

Do not charge alkaline or non rechargeable batteries.

(2)

(3)

INSTALLING THE CHARGE CRADLE

1. Plug the AC adaptor into the rear of the charge cradle and into the

mains power.

2. Place the uh047sx into the charge cradle. The charge light will come on

to indicate the unit is charging.

3. Before operating the uh047sx, charge the battery pack for 16 hours.

Do not charge alkaline or non rechargeable batteries.

USER LICENCE INFORMATION

The citizen band radio service is licenced in Australia by ACMA Radio-communications (Citizen Band Radio Stations) Class Licence and in New Zealand by MED General User Licence for Citizen Band Radio and operation is subject to conditions contained in those licences.

BELT CLIP

To attach the belt clip:

Slide the belt clip until it snaps into place.

To remove the belt clip:

To remove the belt clip, press and hold belt clip locker, slide the belt clip at the same time until released.

LOW BATTERY ALERT

If the battery level becomes low, the battery indicator icon on the display begins flashing. When the batteries in the unit are low, the unit will go into a battery Low mode. The Transmit mode is disabled. Replace the alkaline batteries immediately or if you are using the NiMH battery pack, place the radio on the charge cradle to recharge. Full charge will take up to 16 Hrs.

BACK LIGHT

The uh047sx has an automatic display back light which remains on for 10 seconds after a key press (all keys except PTT key). The back light will work even if the keypad is locked but will not work during low battery alert mode.

(4)

+ 11 hidden pages