Uniden UH037SX-2, UH037SX-4 User Manual

UH037SX-2 and UH037SX-4
UHF Radio Transceiver
OWNER’S MANUAL
CONTROL & INDICATORS
INCLUDED IN YOUR
INCLUDED IN
UH036SX PACKAGE
YOUR PACKAGE
dup
ch/
scan
vol/ mon
mic
1 Antenna 2 PTT (Push-To-Talk) Button 3 Channel/scan up Key 4 Channel/scan down Key
Duplex/Keylock Key
5 Duplex Key 6 Speaker 7 Power On/Off Key 8 Volume up/mon (monitor) Key
UH036SX x 2
UH037SX Radio
Operating Guide
Operating Guide
Belt Clips x 2
Belt Clips
*UH037SX-2 (x2), UH037SX-4 (x4) Other printed materials may be included
RX TX
*
*
9 Volume down/mon (monitor) Key 10 Microphone 11 Battery Compartment Door 12 Channel Indicator 13 Receive Indicator 14 Battery Low Indicator 15 Transmit Indicator
1
OLD
NEW
GETTING STARTED
BATTERY WARNING
To retain the previous user settings, the UH036
The UH037SX will consume a small amount of battery
will continue to use a small amount of battery
power when switched off. To prevent the batteries from
power when switched off. To prevent the batteries from running down, remove them from the radio if the
UH037SX
UH036SX will not be used for long periods.
running down, remove them from the radio if the UH037SX will not be used for long periods.
BATTERY INSTALLATION
Your UH036SX radio uses 3 AAA ALKALINE batteries for power.
UH037SX
Use only good quality alkaline batteries for maximum life and range. Note: Batteries are not supplied.
To avoid damage to the unit do not mix old and new batteries.
1. Make sure your radio is off.
2. Remove the battery cover.
3. Insert 3 AAA ALKALINE batteries according to the polarity symbols inside the battery compartment.
UH037SX
4. Replace the battery cover.
2
WATER WARNING
Uniden does not represent this product to be waterproof. Do not expose this product to Rain or Moisture.
BELT CLIP
To attach the belt clip:
Slide the belt clip until it snaps into place.
To remove the belt clip:
To remove the belt clip. Pinch and hold belt clip and latch (see arrows indicated) and slide the belt clip in the direction shown.
LOW BATTERY ALERT
If the Battery level becomes low, the battery indicator icon will appear on the LCD and begin flashing.
Pinch Belt Clip and Latch
The unit will go into a Battery Low Mode. The Transmit Mode is disabled. Replace the batteries immediately to continue using the radio.
3
OPERATION
POWER ON/OFF
Press and hold to turn the Radio . The channel number
ON
will appear on the display. Press and hold to turn the
OFF
Radio .
VOLUME
Press volume or to increase or decrease the volume level. The Channel indicator will flash when the volume is being adjusted.
ADJUSTING THE KEY BEEPS
Your radio emits a beep each time one of the keys (except for the PTT button and the Key) are pressed.
To turn the beep:
turning the Radio.
To turn the beep:
again.
) are pressed.
OFF
Press and hold the Key while
ON
ON OFF ON
Turn the Radio and then
dup
ch/
scan
dup
vol/ mon
mic
The key beeps cannot permanently be disabled.
4
SELECTING A CHANNEL
Press channel or to select the desired channel.
dup
vol/
ch/
mon
scan
TO TRANSMIT AND RECEIVE
UH037SX
The UH036SX uses the 40 UHF-CB Channels. For your reference a list of the available channels and corresponding frequencies is printed on page 10.
etry and telecommand applications. Transmit is inhibited on these channels).
1. The transmit power of the
UH037SX
UH036SX is 500mW which will provide a range of up to 3+Km.
2. Before you transmit, listen for activity on the selected channel.
3. When the channel is clear, press and hold the to transmit. appears on the LCD.TX
Hold the radio with microphone approximately 5 cm in front of your mouth with the antenna at approximately 45° angle away from your head. Speak in a clear, normal conversational voice.
4. When you have finished speaking,
PTT
release the . then disappears on
PTT
TX
the LCD. Listen for a response.
(Channels 22 and 23 are for telem-
PTT
Switch
PTT
Switch
dup
vol/
ch/
mon
scan
PTT
mic
PTT
TX
While receiving, the RX icon is displayed.
5
channel/ scan
volume/
mon
dup
RX TX
channel/ scan
volume/
mon
dup
RX TX
RANGE
For maximum range and extended the life of the batteries,
avoid touching the antenna
with your hand when transmitting.
Maximum Range
Reduced Range
6
channel/ scan
volume/
mon
dup
RX TX
channel/ scan
volume/
mon
dup
RX TX
INCLUDED IN YOUR UH036SX PACKAGE
UH036SX x 2 Operating Guide Belt Clips x 2
1 Antenna
2 PTT (Push-To-Talk) Button
3 Channel/scan up Key
4 Channel/scan down Key
5 Duplex Key
6 Speaker
7 Power On/Off Key
8 Volume up/mon (monitor) Key
ch/
scan
INCLUDED IN YOUR UH036SX PACKAGE
UH036SX x 2 Operating Guide Belt Clips x 2
1 Antenna
2 PTT (Push-To-Talk) Button
3 Channel/scan up Key
4 Channel/scan down Key
5 Duplex Key
6 Speaker
7 Power On/Off Key
8 Volume up/mon (monitor) Key
ch/
scan
POWER ON/OFF
Press and hold to turn the Radio . The channel number will appear on the display.
ON
OFF
Press and hold to turn the Radio .
OPERATION
mic
vol/ mon
ch/ scan
dup
ADJUSTING THE KEY BEEPS
Your radio emits a beep each time one of the keys (except for the PTT button and the Key) are pressed.
Press and hold the Key while
turning the Radio.
Turn the Radio and then
again.
To turn the beep:
To turn the beep:
OFF
ON
ON OFF ON
dup
VOLUME
Press volume or to increase or decrease the volume level. The Channel indicator will flash when the volume is being adjusted.
The key beeps cannot permanently be disabled.
AUTOMATIC SQUELCH FEATURE
The UH037SX is equipped with an Automatic Squelch system which shuts off weak transmissions and unwanted noise.
For maximum range and extended the life of the batteries, with your hand when transmitting.
avoid touching the antenna
MONITOR
This feature enables users to listen in for weak signals on the current channel at the press of a button.
To use monitor,
Press and hold Volume or for 2 seconds. The RX icon will begin to flash. For continuous listening, the receiver circuit will stay open,
RANGE
letting in both the noise & weak signals. To return to normal receive mode press and hold Volume or for 2 seconds or press key once.
TO OPERATE IN DUPLEX MODE (REPEATERS)
The Duplex function enables you to access local repeater stations. You can only activate Duplex from CH01-CH08. UHF CB Repeaters are used to retransmit or relay your signal. Repeaters will extend the range of your radio and overcome the shielding effect caused by solid obstructions.
Contact your retailer for a list of repeaters available in your area.
Maximum Range
7
6
Reduced Range
Operation with the aid of a Repeater
Eg. CH1 is being used in your area for repeater use. Press momentarily. The icon appears.
Press again to deactivate the duplex operation. UH037SX will return to normal operation.
POWER SAVE
Your UH037SX has a unique circuit designed to dramatically extend the life of the batteries. If there is no transmission nor an incoming call within 2 seconds, your Radio switches to the Power Save mode. The Radio is still able to receive transmissions in this mode.
KEY LOCK
Press and hold / to lock or unlock the keypad. and keys remain functional when key lock is on. When key lock setting is turned on, appears momentarily and will appear when an inactive key is pressed.
SCANNING
The scan function scans all channels and stops at an active channel. When the signal stops, the UH037SX waits 2 seconds (Drop-Out Delay) before
scanning resumes.
8
To initiate scanning,
INCLUDED IN YOUR UH036SX PACKAGE
UH036SX x 2 Operating Guide Belt Clips x 2
INCLUDED IN YOUR UH036SX PACKAGE
UH036SX x 2 Operating Guide Belt Clips x 2
POWER ON/OFF
Press and hold to turn the Radio . The channel number will appear on the display.
ON
OFF
Press and hold to turn the Radio .
OPERATION
mic
vol/ mon
ch/ scan
dup
ADJUSTING THE KEY BEEPS
Your radio emits a beep each time one of the keys (except for the PTT button and the Key) are pressed.
Press and hold the Key while
turning the Radio.
Turn the Radio and then
again.
To turn the beep:
To turn the beep:
OFF
ON
ON OFF ON
dup
VOLUME
Press volume or to increase or decrease the volume level. The Channel indicator will flash when the volume is being adjusted.
The key beeps cannot permanently be disabled.
POWER ON/OFF
Press and hold to turn the Radio . The channel number will appear on the display.
ON
OFF
Press and hold to turn the Radio .
OPERATION
mic
vol/ mon
ch/ scan
dup
ADJUSTING THE KEY BEEPS
Your radio emits a beep each time one of the keys (except for the PTT button and the Key) are pressed.
Press and hold the Key while
turning the Radio.
Turn the Radio and then
again.
To turn the beep:
To turn the beep:
OFF
ON
ON OFF ON
dup
VOLUME
Press volume or to increase or decrease the volume level. The Channel indicator will flash when the volume is being adjusted.
The key beeps cannot permanently be disabled.
Assuming the unit is on CH1 1. when switched on. Press and hold Channel or 2. for 3 seconds and scanning starts.3.
3.
Press or to cancel 4.
scanning.
If Channel or is pressed while the unit is
paused on a channel, scanning will be resumed.
DROP-OUT DELAY
While scanning, the UH037SX stops at a busy channel and receives a transmission. When the received signal is over, the unit will wait for 2 seconds for the return of the signal,
otherwise, the radio resumes scanning.
USER LICENSE INFORMATION
The citizen band radio service is licenced in Australia by ACMA Radio-communications (Citizen Band Radio Stations) Class Licence and in New Zealand by MED General User Licence for Citizen Band Radio and operation is subject to conditions contained in those licenses.
9
POWER ON/OFF
Press and hold to turn the Radio . The channel number will appear on the display.
ON
OFF
Press and hold to turn the Radio .
OPERATION
mic
vol/ mon
ch/ scan
dup
ADJUSTING THE KEY BEEPS
Your radio emits a beep each time one of the keys (except for the PTT button and the Key) are pressed.
Press and hold the Key while
turning the Radio.
Turn the Radio and then
again.
To turn the beep:
To turn the beep:
OFF
ON
ON OFF ON
dup
VOLUME
Press volume or to increase or decrease the volume level. The Channel indicator will flash when the volume is being adjusted.
The key beeps cannot permanently be disabled.
UHF CHANNELS & FREQUENCIES
Please follow these guidelines for channel use in Australia:
• Channels 05 and 35 are Emergency Channels.
• Channel 11 is a Calling Channel.
• Channels 22 and 23 are for telemetry and telecommand applications
and TX is inhibited on these channels. General communication is accepted on all other channels with
these guidelines:
• Channel 40 - road channel (Australia).
Channels 01-08 (and 31-38) are repeater channels.
CH No.
10 11 12 12 14 15 16 17 18 19 20
Simplex Mode
Transmit/Receive
Frequency (MHz)
1 2 3 4 5 6 7 8 9
476.425
476.450
476.475
476.500
476.525
476.550
476.575
476.600
476.625
476.650
476.675
476.700
476.725
476.750
476.775
476.800
476.825
476.850
476.875
476.900
Duplex Mode
Transmit
Frequency (MHz)
477.175 CH31
477.200 CH32
477.225 CH33
477.250 CH34
477.275 CH35
477.300 CH36
477.325 CH37
477.350 CH38
CH No.
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Receive Frequency
Simplex
Moderansmit/
(MHz)
476.925
476.950 (RX only)
476.975 (RX only)
477.000
477.025
477.050
477.075
477.100
477.125
477.150
477.175
477.200
477.225
477.250
477.275
477.300
477.325
477.350
477.375
477.400
10
WARRANTY
UNIDEN UH037SX-2 and UH037SX-4 UHF CB TRANSCEIVER RADIO
Limited One Year Warranty
Note: Please keep your sales docket as it provides evidence of warranty.
Warrantor: Uniden Australia Pty Limited ABN 58 001 865 498 Uniden New Zealand Limited Warranty only available in original country of purchase Elements of Warranty: Uniden warrants to the original retail owner for the duration of this warranty, its UH037SX-2 and UH037SX-4 UHF CB Transceiver Radios (hereinafter referred to as the Product) to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.
Warranty Duration: This warranty to the original retail owner only, shall terminate and be of no further effect ONE (1) year after the date of original retail sale. This warranty will be deemed invalid if the Product is;
(A) Damaged or not maintained as reasonable and necessary, (B) Modified, altered or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) Improperly installed (D) Repaired by someone other than an authorized Uniden Repair Agent for a defect or malfunction covered by this warranty, (E) Used in conjunction with any equipment or parts or as part of a system not manufactured by Uniden, or (F) Where the Serial Number label of the product has been removed or damaged beyond recognition. Warranty only valid in the country of original retail/sale.
Parts Covered: This warranty covers for one (1) year, the Product and included accessories.
Statement of Remedy: In the event that the Product does not conform to this warranty at any time while this
warranty is in effect, the warrantor at its discretion, will repair the defect or replace the Product and return it to you without charge for parts or service. This warranty does not provide for reimbursement or payment of incidental or consequential damages.
This EXPRESS WARRANTY is in addition to and does not in any way affect your rights under the TRADE PRACTICES ACT 1974 (Cth) (Australia) or the CONSUMER GUARANTEES ACT (New Zealand).
Procedure for obtaining performance or warranty: In the event that the Product does not conform to this warranty, the Product should be shipped or delivered, freight pre-paid, with evidence of original purchase (e.g. a copy of the sales docket), to the warrantor at:
UNIDEN AUSTRALIA PTY LIMITED UNIDEN NEW ZEALAND LTD
Service Division Service Division 345 Princes Highway, Rockdale, NSW 2216 150 Harris Road, East Tamaki, Auckland Fax (02) 9599 3278 Fax (09) 274 4253
www.uniden.com.au www.uniden.co.nz
Customers in other states should ship or deliver the Product freight pre-paid to the nearest Uniden Authorised Repair Centre. (Contact Uniden for the Warranty Agent nearest you.)
© 2008 Uniden Australia Pty Limited/Uniden New Zealand Limited Printed in China UTZZ01942ZZ(0)
11
UTZZ01942ZA(0)
2013
Loading...