Uniden Trimline Phone User Manual
Fold
line
Fold
line
Fold
line
Fold
line
Changes or modications to this product not expressly approved by Uniden, or operation
of this product in any way other than as detailed by the owner’s manual, could void your
authority to operate this product.
Industry Canada (I.C.) Notice
Terminal equipment
NOTICE:This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specications. This is conrmed by the registration number. The abbreviation, IC, before
the registration number signies that registration was performed based on a Declaration of
Conformity indicating that Industry Canada technical specications were met. It does not
imply that Industry Canada approved the equipment.
NOTICE:The Ringer Equivalence Number (REN) for this terminal equipment is marked on the
equipment itself. The REN assigned to each terminal equipment provides an indication of
the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not
exceed 5.
One-year Limited Warranty
Important: Evidence of original purchase is required for warranty service. WARRANTOR:
UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden warrants,
for one year, to the original retail owner, this Uniden Product to be free from defects in
materials and craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of no
further eect 12 months after the date of original retail sale. The warranty is invalid if
the Product is (A) damaged or not maintained as reasonable or necessary, (B) modied,
altered, or used as part of any conversion kits, subassemblies, or any congurations not
sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an
authorized Uniden service center for a defect or malfunction covered by this warranty, (E)
used in any conjunction with equipment or parts or as part of any system not manufactured
by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's
manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty
at any time while this warranty is in eect, warrantor will either, at its option, repair or
replace the defective unit and return it to you without charge for parts, service, or any
other cost (except shipping and handling) incurred by warrantor or its representatives in
connection with the performance of this warranty. Warrantor, at its option, may replace the
unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE
AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES
ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR
ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES
NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of
incidental or consequential damages so the above limitation or exclusion may not apply to
you.
LEGAL REMEDIES: This warranty gives you specic legal rights, and you may also have other
rights which vary from state to state. This warranty is void outside the United States of
America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the
instructions in the owner's manual you are certain that the Product is defective, pack the
Product carefully (preferably in its original packaging). The Product should include all parts
and accessories originally packaged with the Product. Include evidence of original purchase
and a note describing the defect that has caused you to return it. The Product should be
shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Corporation
Service Department
4700 Amon Carter Blvd.
Fort Worth, TX 76155
Trimline Phone User's Guide
What's in the box?
If any items are missing
or damaged, contact
our Customer Care Line
immediately. Never use
damaged products.
Need Help? You can get
answers 24/7 at our
website: www.uniden.com.
If You... Contact Uniden’s... Phone
have a question or problem Customer Care Line* 800-297-1023
need a part or accessory Parts Department* 800-554-3988
need special assistance due
to a disability
Accessibility Help Line
800-874-9314
(voice or TTY)
* During regular business hours, Central Standard Time. Visit our website for detailed
business hours.
Important safety precautions
When using your telephone equipment, always follow basic safety
precautions to reduce the risk of re, electric shock and injury to
persons, including the following:
Do not use this product near water, for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
Uniden works to reduce lead content in our PVC coated cords in our products and
accessories.
Warning! The cords on this product and/or accessories contain lead,
a chemical known to the State of California to cause birth defects or
other reproductive harm. Wash hands after handling.
Uniden® is a registered trademark of Uniden America Corporation.
The pictures in this manual are used for examples only. Your actual phone may not look
exactly like the pictures.
►
►
►
Connecting the Phone
Test the connection
Pick up the handset and listen for a dial tone. If you don't hear
one, check the connection between the base and the phone jack.
Make a test call. If the dial won't stop when you dial, check the
Tone/pulse switch: if it’s on tone, change it to pulse, and vice
versa. Try your test call again.
If there is static or noise on the line, see the section on Solving
Problems.
1)
2)
Use the coiled cord to
connect the handset
to the base (use the
jack marked with the
handset icon).
Use the telephone
cord to connect the
line jack to a standard
telephone wall jack.
Route the
cord through
the channel.
Route the
cord through
the channel.
Use the coiled cord to
connect the handset
to the base (use the
jack marked with the
handset icon).
Use the telephone
cord to connect the
line jack to a standard
telephone wall jack.
Route the
cord through
the channel.
Route the
cord through
the channel.
Base
Telephone
cord
Coiled
handset cord
Handset
Front (top panel)Back (bottom panel)Folded inside
Page 1 (outside)
Fold
line
Fold
line
Fold
line
Fold
line
Using the Phone
Flash
button
Boost
button
Volume
dial
Reset
button
Redial
button
Mute
button
Tone/
pulse
switch
Visual
ringer
light
Hook
switch
Ringer
switch
Handset
clip
Button What it does
Boost and
Volume dial
These controls work together to change the volume. See
Changing the Audio Volume.
Flash During a call: switch to a waiting call
Tone/pulse Change the dial mode (see Solving Problems.)
Reset During a call: Hang up the current call and get a dial tone.
Mute
During a call: press & hold to mute the microphone so callers
can’t hear you. Release to turn the microphone back on.
Redial Redial the last number.
Ringer Turn the audio ringer (but not the visual ringer) o or on.
Using Call Waiting
Call waiting is service provided by your local telephone provider;
contact your telephone provider to subscribe to this service.
If you get a Call Waiting call, the handset beeps. Press Flash to
switch between the current call and the waiting call; each time you
switch, there’s a short pause before you're connected to the other
caller.
Changing the Audio Volume
During a call, press Boost to activate the Volume dial. Use the dial
to change the volume. When you’re nished, press Boost again to
deactivate the Volume dial.
Wall-Mounting the Phone
You can mount the phone on
any standard telephone wall
plate where the pins are 100
mm (315/16 inches)
apart.
Before
putting the
handset in
the cradle,
you need to
switch the
handset
clip into
wall mount
mode as
shown in
the drawing
below.
Solving Problems
If you have any trouble with your phone, try these simple steps rst.
If you still have a question or problem, call the Customer Hotline
listed on the front page.
Problem Things to try
I keep hearing a dial tone
when I try to make a call.
Checking the Tone/pulse switch: if it’s on
tone, change it to pulse and try again.
The phone rings, but I can't
hear anything.
Checking the coiled cord connection
between the base and the handset.
Connect the cords as
usual, but route the
line cord through
the inside channel.
Line up the notches on the
base with the pins on the
wall plate. Place the phone
over the plate and slide it
down to lock it into place.
Tuck excess line cord into the
space on the back of the phone.
Connect the cords as
usual, but route the
line cord through
the inside channel.
Line up the notches on the
base with the pins on the
wall plate. Place the phone
over the plate and slide it
down to lock it into place.
Tuck excess line cord into the
space on the back of the phone.
Flip the clip from
front to back.
Slide the
clip out of
its slot.
Rotate the clip
180 degrees.
Slide it
back into
the slot.
Flip the clip from
front to back.
Slide the
clip out of
its slot.
Rotate the clip
180 degrees.
Slide it
back into
the slot.
If there's static on the line
DSL broadband Internet service can
cause static on telephones, but a DSL
lter usually solves any problems. To
get a DSL lter, call your DSL provider
or look in any electronics store.
To install the lter, plug the DSL lter
into the wall jack and then plug your
phone into the lter. Make a test call
to see if the noise is gone.
What Else Do I Need to Know?
FCC compliance information
Part 68 information
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the bottom of this equipment is a label that contains, among other information, a
product identier in the format US: 6NYTE##BXXXXXX (where XXXXXX stands for a specic
model number). If requested, this number must be provided to the telephone company.
An applicable Universal Service Order Codes (USOC) certication for the jacks used in this
equipment is provided (i.e., RJ11C) in the packaging with each piece of approved terminal
equipment. A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also compliant.
See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone
line. Excessive RENs on a telephone line may result in the devices not ringing in response to
an incoming call. In most but not all areas, the sum of RENs should not exceed ve (5.0). To
be certain of the number of devices that may be connected to a line, as determined by the
total RENs, contact the telephone provider. The REN for this product is part of the product
identier that has the format US:6NYTE##BXXXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 18 is a REN of 1.8).
If this equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if
advance notice isn’t practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to le a complaint with the FCC if
you believe it is necessary. The telephone company may make changes in its facilities,
equipment, operations or procedures that could aect the operation of the equipment. If
this happens the telephone company will provide advance notice in order for you to make
necessary modications to maintain uninterrupted service.
If the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
Follow instructions for repairing, if any (e.g. battery replacement section); otherwise do not
substitute or repair any parts of the device except as specied in this manual. Should you
experience trouble with this equipment, contact Uniden customer service at 800-297-1023
to arrange repairs. All repairs must be done by Uniden or an authorized agent.
Connection to party line service is subject to state taris. Contact the state public utility
commission, public service commission or corporation commission for information. This
equipment is hearing aid compatible.
NOTICE: According to telephone company reports, AC electrical surges, typically resulting
from lightning strikes, are very destructive to telephone equipment connected to AC power
sources. To minimize damage from these types of surges, a surge arrestor is recommended.
DSL lter
Telephone
cord
Telephone
wall jack
DSL lter
Telephone
cord
Telephone
wall jack
Page 2 (inside)
Loading...