Uniden PC122AM-SSB User Manual

I

=~o .. -- _..00...

=--=- --=

uni I!n@

AM/SSB

PC122

OWNER'SMANUAL

Mobile CB Radio

/

--:::::::;::~=

WE lCOM E

To the world of sophisticated, microprocessor controlled AM/SSBradio communica-
tions. Your Uniden PC 122 represents the most advanced mobile type radio ever

designed for use in the Citizens Band Radio Service. It will operate on any of the 40
AM frequencies and Upper and Lower Side Band Frequencies designated by the

Department of Communications. Your PC 122 features a frequency synthesizing
circuit with PHASE LOCKLOOPtechniques to assureprecisefrequency control. This

radio has beentype accepted and certified by the D.O.C.

WARNING

Before transmitting with your transceiver,you must obtain a Department of
Communications (D.O.C.) Citizens Radio Licence. Obtain an application
form, from the D.O.C. Before completing the form you should read the
conditions governing the licensing and operation of the C.R.S. (D.O.C.
brochure RB 249). This brochure alsocan be obtained from the D.O.C.After
completing the application form, mail it with the appropriate fee to the
Superintendant Regulatory of Licensingin the State or territory in which the
station willbe operated.

MOBilE INSTAllATION

Plan the location of the radio and microphone bracket before starting installation.
Select a iocation that is convenient for operation and does not interfere with the
driver or passenger in the vehicle. The radio should be securely fastened to a solid
surface usingthe mounting bracket and self-tappingscrewswhich are provided.

"t

-.,

MOBILE ANTENNA

Since the maximum allowable power output of the transceiver is' limited by the
D.O.C., the antenna is a very important factor affecting transmission distance. It is
for this reason that we strongly recommend that you install only a quality antenna in
your new CB radio system. You have purchased a superior quality transceiver. Don't
diminish its performance by installing an inferior antenna.
Only a properly matched antenna system will allow maximum power tranSfer Trom me
50-ohm transmission line to the radiating element. We recommend that you use an
SWR meter when installing your antenna. Set your PC 122 to channel 20 and adjust to

- 1. Your SANTRONICdealer is qualified to assist you in the selection of the

SWR
proper antenna to meet your application requirements.

For automobile installation, the whip antenna may be used with good effect. The most
efficient and practical installation is a full quarter wave whip antenna mounted on the
rear deck or fender top, midway between the rear window and bumper.

A short "Ioaded" whip antenna is more convenient to install on your automobile,
although the efficiency is less than a full quarter wave whip antenna.

For marine installation, consult your dealer for information regarding an adequate

grounding system and prevention of electrolysis between fittings on the hull and
water.

-1-

CONNECTING THE POWER CORDS

With regard to the connection of the power cords, it may be possible or desirable to
connect the red lead (for negative ground systems) or the black lead (for positive
ground systems) to the ignition switch accessory terminal so that the radio is auto-
matically turned off when the ignition switch (key) is turned off.

Alternately, the power lead may be connected to an available terminal on the fuse
block or even to a point in the wiring harness. Care must be taken, however, to guard
against a short circuit condition. When in doubt, please contact your vehicle dealer for
specific information for your vehicle.

GROUND INFORMATION

A negative ground system is generally identified by the" - " battery terminal being
connected to the vehicle motor block, but if you cannot determine the polarity of

your vehicle, consult your vehicle dealer for information.
NOTE: This radio may be installed and used in any 12-volt DC negative or positive

ground system.

NEGATIVE GROUND SYSTEM

If you are operating on a negative ground system, connect the red DC power cord

from the radio to the positive "+" battery terminal or other convenient point and
connect the black power lead to the chassisor vehicle frame, or the negative 11- "
terminal of the battery.

POSITIVE GROUND SYSTEM

If you are operating on a positive ground system, connect the black DC power cord

from the radio to the negative" - " battery terminal or other convenient point and
connect the red power lead to the chassis or vehicle frame, or the positive" + "
terminal of the battery.

-2-

CONTROLS AND FUNCTIONS

@

@ @

@

CD(j)@

1. SQUELCH- The squelch control is used to eliminate background noise during

the absence of a transmission. Turn the control fully counterclockwise, then
slowly rotate it back clockwise until all noise disappears. At this setting any

transmission must be slightly stronger than the background noise to "Break
Squelch" or to be heard. Further clockwise rotation will increase the threshold at

which a signal will be heard. You can select any level to "Break Squelch".

2. S/RF METER - This LED meter shows the relative strength of the received signal

or transmit power.

3. CHANNEL INDICATOR - Displays the channel currently in use.

4. CHANNEL SELECTOR - This switch selects the desired channel for transmission

and reception. All channels, except channel 9, may be used for communications
between stations operating under different license. Channel 9 has been reserved by
the D.O.C. for emergency communications involving the immediate safety of

individuals or the immediate protection of property. Channel 9 also may be used
to render assistance to a motorist. This is the D.O.C. rule and applies to all opera-

tors of CB radios.

5. TX INDICATOR - An LED lights to indicate when the radio is transmitting.

6. MICROPHONE- The operational mode of the CB is controlled by the push-to-

talk switch on the microphone. Press the switch to activate the transmitter and
disable the receiver. Release the switch to enable'the receiver and disable the
transmitter. When transmitting, hold the microphone about 2 inches from your

mouth and speak clearly in a normal voice. The microphone included with the
PC 122 is a detachable, Iow impedance, dynamic type.

7. RF GAIN - This control is used to adjust signal reception in areas where strong
signals are present. Turn the control fully clockwise for maximum reception.

8. VOLUME CONTROL - Rotate clockwise to turn radio on and to increase
volume.

-3-

9. NB/ANL SWITCH - You can select either Noise Blanker and Automatic Noise
Limiter, only Automatic Noiselimiter or all filters OFF. The NBand ANL help to

reduce harsh background noise caused by a variety of interference sources. The
ANLwill not work in the USBor LSBmode.

10. PA SWITCH- Movethis switch to the PublicAddressmode when an external PA
speaker is connected. Whenthe PAmode is selected,you can usethe PAfunction
and yet can monitor CB incoming signals.Adjust the PA output levelby rotating

the volumecontrol.

11. AM/SSBSELECTOR - The three position switch allows you to select AM
(standard 40 channel CB)or USB (Upper Side Band) or LSB (Lower Side Band)
operation.

12. CLARIFIER - Turn this control to achievethe best tuning of the upper or lower

side band receiving frequency.

@@

"

w

@

@

13. ANTENNACONNECTOR- This female connector permits connection of the

transmission line cable male connector (PL-259) to the transceiver.

14. PUBLIC ADDRESS - An external 8 ohm 4-watt speaker must be connected to

the "PA SP" jack located on the back of the unit. The speaker must be directed
aw..ayfrom the microphone to prevent feedback.

15. EXTERNAL SPEAKER - The external speaker jack is used for remote receiver
monitoring. The external speaker should have an 8 ohm impedance and be rated
at least 4 watts. When an external speaker is connected, the internal speaker is

disabled.

16. POWER - This plug permits connection of the DC power to the transceiver. The
supplied DC Cord's plug is polarized which ensures that power will always be
connected and fused properly.

OPERATING PROCEDURE TO RECEIVE

1. Be surethat the power source, antenna and microphone are properly connected.

2. Turn the unit on by rotating the Volumecontrol clockwise.

3. Set the channel selector switch to the desired channel.

4. Setthe Volume control to acomfortable listening level.

5. Listen to the background noise from the speaker. Turn the Squelch control clock-
wise until the noise disappears (no signal should be present). Leavethe control at

-4-

this setting. The squelch is now properly set. The receiverwill remainquiet until a
signal is actually received. Do not advance the control too far, or some weaker
signalswill not be heard.

OPERATING PROCEDURE TO TRANSMIT

1. Select the desiredchannel for transmission.

2. If the channel is clear, depress the push-to-talk switch on the side of the micro-
phone and speak in a normal voice.

CAUTION: The transceiver Voltage Standing Wave Ratio (V.S.W.A.)measurement
must be performed prior to the use of the transmitter. A "V.S.W.R." ratio in excessof
2:1 may damagethe transmitter.

OPERATION OF SSB

Choose the desired side band frequency by, A; select standard channel (1 - 40), B;

select Upper or Lower side b~md by moving AM/SSB switch. Transmit or receive
according to previous instructions.

When receiving a side band transmission you may need to use the Clarifier control to
fine tune that frequency. Rotate the Clarifier clockwise or counterclockwise for
optimum reception.

PREVENTATIVE MAINTENANCE

At six to twelve month intervals,the following systemchecks should be made:

1. Checkthe Standing WaveRatio (V.S.W.R.)

2. Inspect all electricalconnections.

3. Inspect antenna coaxial cable for wear.

4. Inspect all screwsand other mounting hardware.

TROUBLE SHOOTING

If your PC 122 is not performing up to your expectations, please try these simple
steps. If you still cannot get satisfactory results after readingthis manual and following
the trouble shooting steps, you may need to haveyour unit serviced.

trouble

Unit willnot turn on.

Nopower

Poor reception

Weak transmission

check

1. Checkpower cord and allconnections.

2. Check powercord fuse.

3. Check vehicleelectricalsystem.

1. Checkand adjust Squelch.

2. Check antenna system and cable, connectors.

3. Check operation mode of the radio.

1. Checkantenna system and cable, connectors.

2. Checkantenna grounding.

3. Checkfor corrosion on connectors.

-5-

If you determine that service is necessary, contact your local dealer or pack the unit in
its original carton. Send it along with a brief, concise description of the problem, your
name, address, phone number, and a copy of the original purchase receipt to the
address listed in the warranty.

SERVICING YOUR CB

Technical information, diagrams and charts will be provided upon request. It isthe
user's responsibility to see that this radio is operating at all times in accordancewith

. the D.O.C. Citizens Radio Service regulations.Wehighly recommendthat you consult

a qualified radiotelephone technician for service and alignment of this radio. When
ordering parts, it is important to specify the correct model number and serial number

of this radio.
Please refer to the WARNING information on the first page of this manual.

SPECIFICA TIONS

GENERAL

Channels

Frequency Range

Frequency Control

Frequency Tolerance: 0.005%
Operating Temp. : -30°C to +50oc
Microphone : Plug in type; dynamic

Input Voltage: 13.8 VDC nom. (+ or -

Current Drain

Size : 6"W x 7%"D x 2"H
Weight : 2 lb. 10 oz.

Antenna Connector: UHF, SO-239
Semiconductors: 41 transistors, 7 IC, 49

LED Meter

TRANSMITTER

Power Output

Modulation
Intermodulation

Distortion

SSB Carrier
Suppression

: 40 AM, 40 use, 40 LSB
: 26.965 to 27.405 MHz

: Phase Lock Loop (PLU

synthesizer

ground)

: TX: AM full mod., 2.2 A,

SSB 12 watts PEP out-
put, 2 A

RX: AM & SSBwith max

audio output 0.6 A

diodes

: Indicates relative power

output and receive signal
strength

: AM 4 watts, SSB 12

watts P.E.P.

: ClassB amplitude

modulation

: SSB:3rd and 5th order,

better than -25dB, 7th

and 9th order better than

-35dB

: Better than -55dB

Unwanted Sideband: Better than - 5OdB

Freq. Response: 300 - 3000 Hz

Output Impedance: 50 ohms, unbalanced
SSBFilter : 10.695 MHz, 8 pole

RECEIVER

Sensitivity

Selectivity
Cross Modulation

Image Rejection
I.F. Frequency

Automatic Gain
Control

Squelch
Clarifier : t1.5KHz

AudioOutput Power:3watts into 8 ohms

Freq. Response: 350 to 2500 Hz
Distortion : Less than 10% at 3 watts

Internal Speaker
External Speaker

PA System

monolithic type

4.2KHz, 6OdB@7.0KHz

: SSB: Better than .25/JV

for 1OdB; (S +

greater than 1/2 watt of
audio output, AM; Bet-
ter than .5 /JV for 10 dB;
(S + N)/N @ greater than
1/2 watt of audio output

: SSB and AM; 6dB @ 4.2

KHz,6OdB@7.0KHz

: More than SOdB

6dB @

N)/N @

: Morethan 75dB

: AM and SSB; 10.695

MHz

: (AGC): less than 1OdB

change in audio output
for inputs from 10 to
500,000 microvolts

: Adjustable; threshold less

than .5 /JV

output

: 16 ohms, round
: (not supplied) 8 ohms

: 3 watts in external 8 ohm

speaker

f ,

-6-

~

uniden@

12 MONTHS FULL WARRANTY

WARRANTOR. SANTRONIC AGENCIES PTY. LTD. 13 Garema Circuit,

Kingsgrove NSW 2208 ("SANTRONIC").

ELEMENTS OF WARRANTY. SANTRONIC warrant$, for the duration of this
warranty, its UNIDEN CB Product to be free from defects in materials and crafts-
manship with only the limitation or exclusions set out below.
WARRANTY DURATION. This Warranty shall terminate and be of no further effect
One (1) year after the date of original purchase of the Product or at the time the

Product is (a) damaged or not maintained as reasonable and necessary, (b) modified,
(cl improperly installed, (d) is repaired by someone other than Warrantor for a

defect or malfunction covered by this Warranty, or (e) used in a manner or purpose

for which the Product was not intended.

PARTS COVERED. This Warranty covers all components of the Products.
STATEMENT OF REMEDY. In the event that the Product does not conform to this
Warranty at any time while this Warranty is effective, Warrantor will repair the defect
and return it to you prepaid, without charge for parts, service, or any other costs
incurred by Warrantor or its representatives in connection with the performance of

this Warranty. In addition, if the Product contains a defect or malfunction which is
not repaired after a reasonable number of attempts by Warrantor to repair the
Product, the Product or defective component will, at our discretion, be replaced
without charge, when the defective product is delivered to the warrantor at 13
Garema Circuit Kingsgrove NSW 2208 free and clear of all liens and encumbrances.
Please note that while the Product will be remedied under this Warranty without
charge, THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIM-

BURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES.

Some states do not allow this exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY. In the event
that the Product does not conform to this Warranty, the Product should be shipped
prepaid to Warrantor at 13 Garema Circuits Kingsgrove NSW 2208. THE ORIGINAL

OR COpy OF THE SALES RECEIPT OR OTHER VALID EVIDENCE OF THE
DATE OF THE ORIGINAL PURCHASE MUST ACCOMPANY THIS PRODUCT.

LEGAL REMEDIES. This Warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.

UTSN01549DZ

San ironic )

AGENCIES PTY. LTO.

13 GAREMA CIRCUIT, KINGSGROVE
PHONE [phone], TELEX AA73170
P.O. Box 12, Kingsgrove, NSW 2208

BRISBANE: 3/12 RANDALLST
SLACKS CREEK, OLD 4127

PHONE [phone]

@Copyright 1985 Uniden Corporation

Print~d in Taiwan