Uniden FRS440 User Manual

IINNSSTTAALLLL TTHHEE BBAATTTTEERRYY

Your FRS440 radio uses 3 AA Alkaline batteries for
power.We recommend using Duracell Ultra alkaline
batteries.

To install the batteries:

1) Make sure your radio is off.

2) Remove the battery
compartment door by placing your thumb at the top
of the compartment, press down and slide it away
from the unit.

3) Install 3 AA Alkaline batteries (not included) into the
battery compartment. Be certain to follow the
+ and - symbols in the compartment. Installing the
batteries incorrectly will prevent the unit from
operating.

4) Optional:Your FRS440 radio can be powered using
an optional NiMH battery pack specifically designed
for this model.Remove the alkaline batteries and
install the battery pack by inserting into the battery
compartment. Follow the instructions found with the
NiMH accessory.

5) Replace the battery compartment door by pushing it
up until it is secure.

This unit has a battery level meter on the display to
indicate the status of the batteries.When the batteries in
the unit are low, the battery meter will flash and the unit
will emit a tone.Replace the batter ies immediately or if
you are using the optional NiMH battery pack, you must
recharge the batteries in order to continue using the
radio.

Congratulations on your purchase of the Uniden RS440
Family Radio.This product is a lightweight, palm-sized
radio with a unique carabineer design allowing you to
"clip" the radio to almost anything and carry it almost
anywhere.Use it at shopping malls, amusement parks,
or sporting events to stay in contact with family and
friends, or in a neighborhood watch for vital
communication.This compact, state-of-the-art device is
equipped with many features.

OOPPTTIIOONNAALL AACCCCEESSSSOORRIIEESS

Your package contains the FRS440 radio, this reference
guide, and a product registration card. You will need to
purchase 3 AA Alkaline batteries in order to operate the
unit.The following optional accessories may be
puchased from your participating Uniden dealer or call
1-800-554-3988 or visit us on the web at
www.uniden.com

•Earset Mic w/ PTT - #HS2468

•Vox Headset Mic - #HSV2469

•NiMH Battery Pack w/AC Charger and
DC Car Charger - #BPCC240

•Multi Color Grips ­Available at www.uniden.com

Adjusting the Sound (Key Beeps)

Your radio emits a beep each time one of the buttons is
pressed.To turn this sound off, press call/menuwhile
turning on the radio.To turn this sound on, press
call/menu while turning on the radio again.

Choosing a Channel

Your radio has 14 channels and 38 CTCSS codes you
can use to talk to others.In order to speak to someone,
each of you must be set to the same channel and
CTCSS code.

To choose a channel:
Press the ▲ or ▼button to increase or decrease the
channel number displayed.

Navigating through the Menu

To access the advanced features of the FRS440, your
radio has a menu function.

1) To enter the menu, press and hold the call/menu
button for 1 second.

2) Additional presses of the call/menu button will
advance through the menu until exiting to
"normal" operating mode.

3)Other methods of exiting the menu function are:

a. Press and hold the call/menu button for 1 second

again.

b. Press PTT.
c. Wait 10 seconds until the unit automatically returns to

"normal" mode.

3

THANK YOU

FOR PURCHASING A UNIDEN PRODUCT

BBAATTTTEERRYY LLEEVVEELL AANNDD

LLOOWW BBAATTTTEERRYY AALLEERRTT

Talking on Your Radio

To talk to others using the radio:

1) Press and hold the PTT button and speak in a
clear, normal voice about 2-3 inches away from
the microphone.To avoid cutting off the first part
of your transmission, pause slightly after
pressing the PTT button before you start talking.

2) When you are finished speaking, release the
PTT button.

Transmitting a Call Alert Tone:

Your FRS440 radio is equipped with 5 selectable call
tones that will be transmitted when the call/menu
button is momentarily pressed.

To select a call tone:

1) Enter the Menu.Advance through the menu until
the call icon on the display is shown.The current
call tone number (1-5) will be indicated.

2) Press the ▲ or ▼ button to increase or
decrease the number to the desired call tone.
Each tone will be heard through the speaker.

3) Exit the Menu.

To transmit the selected call alert tone, momentarily
press the call/menu button.The selected tone will
automatically be transmitted for a fixed length of
time.

Note:Do not hold the call/menu button down as this
will cause the unit to enter the Menu mode.

*Range may vary depending on environmental and/or topographical conditions.

Vibrate Alert for Incoming Calls

Your FRS440 radio is equipped with a vibrator that
can be used for notification of an incoming call alert
from other Uniden radios equipped with the same
feature.

To select the vibrate alert:

1) Enter the Menu and then press the call/menu
button twice.The VIBRATE icon on the LCD
display will be shown along with on or off
indicating the vibrate alert feature status.

2) Press either the ▲ or ▼ button to toggle the
feature on or off.

3) Exit the Menu.

Channel Scan Feature

Your FRS440 radio has a channel scan feature that
allows you to easily scan all 14 channels.When an
active channel is detected, the unit will pause on that
channel until the channel is clear.Then after a
4 second delay, the unit will continue scanning.
Pressing PTT while the scan is paused on a channel
will allow you to transmit on that channel.
To turn on channel scanning:
Press and hold either the ▲ or ▼ button until the
SCAN icon on the display is shown. The channel
number on the display will rapidly cycle through the
channels.

Ambient Temperature Display

Your radio will periodically display the ambient
temperature either in degrees F° or degrees C°.

To change this setting:

1) Enter the Menu.Advance through the menu
until the TEMPERATUREicon on the display
is shown.The letters F or C will be blinking
indicating the selection.

2) Press either the s or t button to toggle
between F or C.

3) Exit the Menu.

Note:Once the radio is turned on, please allow
time for an accurate temperature reading to be
collected.

• 5 Selectable Call Tone Alert

• Ambient Temperature Display

• Vibrate Alert for incoming calls

• 7 NOAA Weather Channels

• Optional NiMH Battery Pack

• Optional Headset Accessories

• Channel Monitor

• 14 Channels

• 38 CTCSS Codes

• Up to 2 mile range*

• Battery Level Meter

• FM Radio

• LCD Display

• Countdown Timer

• Channel Scan

FRS440

Auto Squelch Feature

The FRS440 radio is equipped with an automatic
squelch system which shuts off weak
transmissions and unwanted noise due to terrain
conditions or if you have reached your range
limit.

To temporarily disable the Auto Squelch and
monitor the selected channel, rapidly press the
PTT button twice.Press any key to exit channel
monitor mode.The channel will remain open until
the PTT button is pressed.
To re-engage the Auto Squelch, repeat the
double PTT key press.

Automatic Power Save Feature

Your radio has a unique circuit designed to
dramatically extend the life of the batteries.If
there is no transmission within 5 seconds, your
radio switches to the Power Save mode.The
radio is still able to receive transmissions in
this mode.

Countdown Timer Feature

Your radio has a countdown timer which can be
set from 5 minutes to 3 hours in 5 minute
increases.When the timer is running, the
ALARM icon is shown on the display.The icons
around the display provide a visual indication of
how much time is remaining on the timer.

To set the countdown timer:

1) Enter the Menu.Advance through the menu
until the ALARM icon on the display is
shown.The current timer setting will be
flashing on the display.

Note:When zero (0) is displayed, the timer

is off.

2) Press either the s or t button to change
the setting to the desired count.

3) Exit the Menu.The timer will begin
counting down immediately.

Note: If Vibrate Alert is enabled or Key Beep
Tones are turned off, the radio will vibrate when
the countdown timer expires.

Turning the Radio On and Adjusting the Volume

1) Rotate the on/off/volume control clockwise to turn the
unit on and increase the speaker volume.

2) Rotate the on/off/volume control counterclockwise to
decrease the speaker volume and turn the unit off.

UUSSIINNGG TTHHEE RRAADDIIOO

In order to get the most out of your new radio, read this
reference guide completely before attempting to operate
the unit.

Your unit has (3) modes of operation.

1) FRS Radio Mode

2) Weather Radio Mode

3) FM Radio Mode

The Weather Radio Mode and FM Radio Mode will be
discussed later.

To turn off channel scanning:
Press any key to cancel SCANmode.

1) Enter the menu.Advance through the menu, the
CTCSS code on the LCD display will flash.

2) Press the ▲ or ▼ button to increase or decrease
the code number displayed.

3) Exit the Menu to return to "normal" mode.

Choosing a CTCSS Code

Each of the FRS channels 1-14 may have any one of the
codes 0-38 selected.Code "0" indicates no CTCSS code
selected and your radio can receive a signal regardless
of the code settings of the transmitting radio.

FCC Information

This device complies with Part 15 of the FCC Rules Subpart-B.Operation is subject to the following conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference that may cause undesired operation.
Important: Do not open your radio to make any internal adjustments.Your radio is set up to transmit a regulated signal on an assigned frequency. It is against the law
to alter or adjust the settings inside the radio to exceed those limitations.Any adjustments to your radio must be made by qualified technicians using the proper test
equipment.
To be safe and sure:

• Never open your radio’s case.

• Never change or replace anything in your radio except the batteries.
Your radio might cause TV or radio interference even when it is operating properly.To determine whether your radio is causing the interference, turn it off. If the
interference goes away, your radio is causing it. Try to eliminate the interference by moving your radio away from the receiver. If you cannot eliminate the interference,
the FCC requires that you stop using the radio.
Audio Accessories:Do not operate the radio with audio accessories at high volume levels.Hearing experts advise against continuous high volume operation.If you
experience a ringing in your ears, reduce the volume level or discontinue use.Always make sure the radio is turned off before plugging audio accessories into the
accessory jack.
Hazardous Environments:Do not operate the radio in hazardous environments.Explosion or fire may result.Do not operate the radio near unshielded electrical
blasting caps.Under certain conditions, radios can interfere with blasting operations and may cause an explosion.Turn your radio OFF to prevent accidental
transmission when in a blasting area or in areas posted:“Turn off two-way radio.”Construction crews often use remote control RF devices to set off explosives.
Care and Safety:To clean the radio, use a soft cloth dampened with water.Do not use cleaners or solvents because they can harm the body of the unit and leak
inside, causing permanent damage.Use a dry, lint-free cloth to clean the battery contacts.Do not submerge the unit in water.If the unit gets wet, turn it off and
remove the batteries immediately.Dry the battery compartment with a soft cloth to minimize potential water damage.Leave the battery compartment cover off
overnight to ensure complete drying. Do not use the radio until the unit is completely dry.

OONNEE YYEEAARR LLIIMMIITTEEDD WWAARRRRAANNTTYY

Important: Evidence of original purchase is required for warranty service.

WARRANTOR:UNIDEN AMERICA CORPORATION (“Uniden”)ELEMENTS OF WARRANTY:
Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or
exclusions set out below.
WARRANTY DURATION:This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale.The warranty is invalid if the
Product is:
(A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden,
(C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed
by the owner’s manual for this product.
STATEMENT OF REMEDY:In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or
replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its
representatives in connection with the performance of this warranty.Warrantor, at its option, may replace the unit with a new or refurbished unit.THE LIMITED
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES
OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OVERPAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES.Some states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES:This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.This warranty is void outside the United States of
America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY:If, after following the instructions in the owner’s manual you are certain that the Product is defective, pack the
Product carefully (preferably in its original packaging).The Product should include all parts and accessories originally packaged with the Product. Include
evidence of original purchase and a note describing the defect that has caused you to return it.The Product should be shipped freight prepaid, by traceable means, to warrantor:

Uniden America Corporation

Parts and Service Division

4700 Amon Carter Blvd., Fort Worth, TX 76155

[phone], 7 a.m.to 7 p.m.Central, Monday through Friday

www.uniden.com

Sport Clip - U.S.patent pending
Covered under one or more of the following U.S. patents:
4,684,870 4,734,049 4,963,844 5,203,015 5,214,789 5,491,745
5,497,508 5,517,677 5,557,606 5,613,201 5,628,059 5,634,196
5,634,205 5,678,176 5,722,070 5,787,345 5,526,528 5,574,994
5,610,946 5,697,096 5,717,312 5,901,341 6,021,326

SSPPEECCIIFFIICCAATTIIOONNSS

Channels 14 FRS, 7 Weather
CTCSS Codes 38 Sub-Audible Tones
Operating Frequency UHF 462.550- 467.725 MHz

VHF 162.400-162.550 MHz

Power Source 3AA Alkaline Batteries

or custom NiMH Battery Pack
Output Power 500mW ERP maximum
Battery Life 50 Hours (5/5/90 duty cycle)

Frequency Chart

Ch. Freq. Ch. Freq.
1 462.5625 8 467.5625
2 462.5875 9 467.5875
3 462.6125 10 467.6125
4 462.6375 11 467.6375
5 462.6625 12 467.6625
6 462.6875 13 467.6875
7 462.7125 14 467.7125

CTCSS Chart (Hz)

Code Freq. Code Freq.
0 Disabled 20 131.8
1 67.0 21 136.5
2 71.9 22 141.3
3 74.4 23 146.2
4 77.0 24 151.4
5 79.7 25 156.7
6 82.5 26 162.2
7 85.4 27 167.9
8 88.5 28 173.8
9 91.5 29 179.9
10 94.8 30 186.2
11 97.4 31 192.8
12 100.0 32 203.5
13 103.5 33 210.7
14 107.2 34 218.1
15 110.9 35 225.7
16 114.8 36 233.6
17 118.8 37 241.8
18 123.0 38 250.3
19 127.30

© 2001 Uniden America Corporation
All rights reserved • Printed in China
UTZZ-440

Your FRS440 radio can receive FM radio stations from 87.7Mhz to 107.9Mhz. While
using the FM Radio, you are not able to receive FRS communications unless you
press the PTT or call/menu buttons which will immediately exit and return to
FRS Radio Mode.

To turn on the FM Radio:

1) Enter the Menu.

2) Press either the Up or Down button until the FM icon is shown indicating the
FM Radio Mode.

3) Exit the Menu.

Choosing an FM Station

Press the s or t button to scroll through the FM stations.A momentary key press
will change the setting by small steps.

Automatic Seek Feature

Press and hold the ▲ or ▼ button for more than 1 second.The FRS radio will begin
scanning the FM band.Your FRS radio will stop on the next available channel for
5 seconds, then continue on to the next available channel.To stop the
Automatic Seek Feature, press the ▲or ▼ button.

UUSSIINNGG TTHHEE FFMM RRAADDIIOO

NOAA Weather Radio Frequency List

Channel 1 162.550 Mhz Channel 5 162.450 Mhz
Channel 2 162.400 Mhz Channel 6 162.500 Mhz
Channel 3 162.475 Mhz Channel 7 162.525 Mhz
Channel 4 162.425 Mhz

To return to the FRS Radio:

1) Enter the Menu.

2) Press either the s or t button until the channel numbers on the display are
flashing indicating the FRS Radio Mode.

3) Exit the Menu.

Your FRS440 radio can receive weather broadcasts from the NOAA National
Weather Service. While using the Weather Radio, you are not able to receive
FRS communications unless you press the PTT or call/menu button which will
immediately exit and return to FRS Radio Mode.

To turn on the Weather Radio:

1) Enter the Menu.

2) Press either the s or t button until the WX icon is shown indicating the
Weather Radio Mode.

3) Exit the Menu.

Choosing a Weather Channel

There are 7 NOAA channel frequencies available and these frequencies are

common between the US and Canada.You will need to know what frequency is

being transmitted in your location.
Press the s or t button to increase or decrease the channel number

displayed.The Auto Squelch feature is never active in Weather Radio Mode.

UUSSIINNGG TTHHEE WWEEAATTHHEERR RRAADDIIOO

LCD Backlight

The LCD backlight will automatically turn on with any key press.The LCD display
will illuminate for 5 seconds before turning off.

To return to the FRS Radio:

1) Enter the Menu.

2) Press either the s or t button until the channel
numbers on the display are flashing indicating the
FRS Radio Mode.

3) Exit the Menu.