Uniden EXI 7246 Series, EXI7246B, EXI7246G, EXI7246P, EXI7246C Owner's Manual

Uniden EXA32

45.book 3 ページ ２００３

年１２月１７日　水曜日　午

前１１時３１分

QUICK REFERENCE GUIDE

EXI7246/EXI7246C

Make sure your cordless phone's
packaging includes the following items.

Base Handset AC adapter Belt Clip

Rechargeable

battery

Telephone

cord

Also included: • Owner's manual

Wall mount

adapter

Plug the other end into the
telephone wall jack.

Plug one end of the
telephone cord into
the base TEL LINE
jack.

Step 2 Install Handset Battery Pack and Charge

Remove the
cover.

Connect the
battery pack

Note

Use ONLY the Uniden recharge­able battery pack supplied with
your new phone!

Step 1 Checking the Package Contents

Plug the AC Adapter cord to
the DC IN 9V jack (yellow) .

Plug the AC Adapter to a
120V AC power outlet.

Route the cord.Route the cord.

Note

Use ONLY the Uniden AC Adapter
supplied with your new phone!

Place the handset in
the base.
Make sure that
charge LED

Step 3 Set up the Base

Step 4 Charging the Handset

Step 5 Connect to the Phone Line

Step 6 Make & Receive Calls

To Make a C a l l

To Receive a Call

Press

talk/flash .

Listen for dial
tone.

Dial the desired
number.

Pick up the handset
and press talk/flash .

Additional Features

For more information on these and
other features, please refer to your
Owner's Manual. For your
convenience, listed below are
important features that will help
you set up your new cordless phone.

Refer to your Owner's Manual

Handset/Base Set up:

- Adjust the Earpiece

Volu me →P.18

- Set the Ringer Volume →P.1 6

- Set Tone/Pulse Dialing →P.1 5

Caller ID:

Set Caller ID on Call Waiting

(CIDCW) →P.13

Note: You must subscribe to Caller
ID services through your local
telephone provider to use Caller
ID and CIDCW.

UP033BH_EXI7246C.book 1 ページ ２００４年１月１５日　木曜日　午前１１時４７分

EXI7246/EXI7246C

Asegúrese de que haya recibido los siguientes
artículos en el paquete (la cantidad de artículos
puede variar según el modelo que haya comprado)

Base Receptor

Adaptador

CA

Pinza para

la correa

Pila

recargable

Cable

telefónico

Además

va incluido: • Manual del usuario

Adaptador para el

montaje en la pared

Conecte el otro extremo en el
enchufe telefónico de la pared.

Al enchufe telefónico

Cable de la línea telefónica
(suministrado)

Al enchufe TEL LINE

Conecte un
extremo de la línea
telefónica en el
enchufe TEL
LINE en la base.

2° Paso

Instalación y carga de la pila para el receptor

Quite la tapa.

Conecte el
paquete de

Nota ¡Use SOLAMENTE el paquete de

pilas recargable de Uniden sumi­nistrado con su nuevo teléfono!

1° Paso

Inspección del contenido del embalaje

Conecte el adaptador CA en el
enchufe (amarillo)

CC IN 9V

.

Conecte el adaptador CA en
una toma de 120V CA.

Route the cor

Route the cord.d.

Pase el cable

A la toma CA

Al enchufe CC IN 9V

Adaptador CA
(suministrado)

Note ¡Use SOLAMENTE el adaptador CA de

Uniden suministrado con su teléfono!

Coloque el receptor
en la base.
Asegúrese de que el
LED de carga se

3° Paso Programación de la base

4° Paso Carga del receptor

5° Paso Conexión de la línea telefónica

6° Paso Realización y recepción de llamadas

Para hacer una llamada

Para recibir una llamada

Oprima

talk/flash .

Espere por el tono
de marcación.

Marque el
número deseado.

Levante el receptor y
oprima

talk/flash .

Características adicionales

Para más información sobre estas y
otras características, le rogamos que
consulte su Manual del usuario. Para
su conveniencia, hemos listado abajo
unas características importantes, las
cuales le ayudarán a programar su
nuevo teléfono inalámbrico de Uniden.

Programación del receptor/base:

- Ajuste del volumen del timbre y

del auricular →P.1 8

- Programación del volumen del

timbre →P.16

- Programación de la marcación

por tono/pulso →P.1 5

Identificación de llamadas (Caller ID):

Programe la Identificación de llamadas
en Llamadas en espera (CIDCW)→P.1 3

Nota: Usted debe estar suscrito al
servicio de Identificación de llama­das con su proveedor de telefonía
local para poder usar las caracterís­ticas de Caller ID y de CIDCW

UP033BH_EXI7246C.book 2 ページ ２００４年１月１５日　木曜日　午前１１時４７分

Contents

QUICK REFERENCE GUIDE 1
Welcome/Features 4
Controls and Functions 5
Terms Used in this Manual 6
Getting Started

Installing the Phone 7

A. Choose the Best Location 7
B. Install the Rechargeable Battery Pack into the Handset 8
C. Connect the Base Unit and Charge the Handset 9
D. Mount the base unit on a wall 10
Installing the Beltclip 11
Headset Installation 12

Basic Setup 13

Activating AutoTalk 13
Activating Caller ID on Call Waiting 13
Entering Your Area Code 14
Choosing the Dialing Mode 15
Setting the Language 15
Selecting the Ring Tone and Volume 16

Using Call Waiting 20
Voice Mail Waiting Indicator 21

RocketDial

RocketDial 22

Storing the RocketDial 22

Using the Speed Dial Memory

Using the Speed Dial Memory 23

Storing Names and Numbers in Speed Dial Memory 23
Storing Caller ID messages in Speed Memory Locations 26
Making Calls from Speed Dial Memory 27

Caller ID Features

Caller ID and CIDCW (Caller ID on Call Waiting) 28

When the Telephone Rings 28
Viewing the Caller ID Message List 29
Deleting Information from the Caller ID List 30
Making a Call from the Caller ID List 31

Additional Information

Changing the Digital Security Code 32
Note on Power Sources 33
General Information 35

UP033BH_EXI7246C.book 3 ページ ２００４年１月１５日　木曜日　午前１１時４７分

As an Energy Star Partner, Uniden has determined that this product or product
models meets the Energy Star



guidelines for energy efficiency.

Energy Star



is a U.S. registered mark.

Welcome

Features

• 2.4GHz Extended Range Technology

• 3 Line Backlit Display

• Caller ID and Caller ID on Call Waiting

• 10 Number Memory Dialing

• One touch RocketDial®

• Last Number Redial

• Voice Mail Waiting Indicator

• English, French or Spanish Support

• Pulse/Tone Dialing

•Find Handset

• Earpiece Volume Control

•Ringer Volume Control

• Hearing Aid Compatible

• 20 Channel Autoscan

Congratulations on your purchase of the Uniden cordless telephone. This phone is designed and
engineered to exacting standards for reliability, long life, and outstanding performance.

Note:Illustrations in this manual are used for explanation purposes. Some

illustrations in this manual may differ from the actual unit. The color of your
cordless phone may vary.

UP033BH_EXI7246C.book 4 ページ ２００４年１月１５日　木曜日　午前１１時４７分

6

5

7
8

12
13

14

4

1

2

3

Controls and Functions

CONTROLS & FUNCTIONS

1. Handset antenna

2. Jack for optional headset

3. Beltclip hole

4. Handset battery compartment

5. Handset earpiece

6. LCD display

7. caller id/menu key (pages 13 and 28)

8. / /vol/ (earpiece volume, ringer
volume and scroll) key (pages 13, 16 and

18)

9.

*

/tone/← key (left cursor) key

(pages 19 and 23)

10. redial/pause key (pages 18 and 25)

11. select key (page 13)

12. Rocketdial key (page 22)

13. talk/flash key (pages 17 and 20)

14. end key (pages 17 and 18)

UP033BH_EXI7246C.book 5 ページ ２００４年１月１５日　木曜日　午前１１時４７分

23 24

21

22

20

20. Base charging contacts

21. find handset key (pages 20 and 32)

22. charge/in use and VMWI
(Voice Mail Waiting Indicator) LED

23. DC IN 9V jack

24. Telephone line jack

Terms Used in this Manual

• Standby Mode - The handset may be sitting in or off the base, but is NOT in use. The talk/flash key has not

been pressed and there is no dial tone.

UP033BH_EXI7246C.book 6 ページ ２００４年１月１５日　木曜日　午前１１時４７分

Installing the Phone

Do the following steps:

A. Choose the Best Location
B. Install the Rechargeable Battery Pack into the Handset
C. Connect the Base Unit and Charge the Handset
D. Mount the Base Unit on a Wall

A. Choose the Best Location

When choosing a location for your new phone, here are some important guidelines you should
consider:

Avoid heat sources, such as radiators,
air ducts, and sunlight

Avoid television sets and other
electronic equipment

Choose a central location

Avoid noise sources such as a window by
a street with heavy traffic

Avoid microwave ovens

Avoid excessive moisture,
extremely low temperatures, dust,
mechanical vibration, or shock

Avoid personal computers

If your home has
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.

If you have questions
about what will disable
your alarm equipment,
contact your telephone
company or a qualified
installer.

note

GETTING STARTED

UP033BH_EXI7246C.book 7 ページ ２００４年１月１５日　木曜日　午前１１時４７分

B. Install the Rechargeable Battery Pack into the Handset

The handset is powered by a rechargeable battery pack.
The battery recharges automatically when the handset is placed
in the base unit.

1) Press down on the handset battery case cover (use the
finger indention for a better grip) and slide the cover
downward to remove.

2) Plug the battery pack connector (red & black wires) into the
jack inside the battery compartment.
(The connector notches fit into the grooves of the jack only
one way.) Match the wire colors to the polarity label in the
battery compartment, connect the battery and listen for a
click to insure connection.

3) Make sure you have a good connection by slightly pulling on
the battery wires. If the connection is secure, the battery
jack will remain in place.

•Use only the Uniden
(BT-905) rechargeable
battery pack supplied
with your cordless
telephone.

•Replacement batteries
are also available
through the Uniden
Parts Department at
[phone],
Monday through Friday
from 8:00 a.m. to 5:00
p.m. or online at

www.uniden.com

!

GETTING STARTED

UP033BH_EXI7246C.book 8 ページ ２００４年１月１５日　木曜日　午前１１時４７分

C. Connect the Base Unit and Charge the Handset

1) Connect the AC adapter to the DC IN 9V jack and to

a standard 120V AC wall outlet.

2) Place the handset in the base unit with the keypad
facing forward.

3) Make sure the charge/in use LED illuminates.
If the LED does not illuminate, check to see that the AC
adapter is plugged in and the handset makes good
contact with the base charging contacts.

• Connect the AC adapter to a continuous power
supply.

• Place the base unit close to the AC outlet so that
you can unplug the AC adapter easily.

4) Charge your handset at least 15-20 hours before
plugging into the phone line.

Route the cord.

Route the cord.

Route the cord.

•Use only the supplied
AD-0001 AC adapter.
Do not use any other
AC adapter.

•Do not place the power
cord where it creates a
trip hazard or where it
could become chafed
and create a fire or
electrical hazard.

!

GETTING STARTED

UP033BH_EXI7246C.book 9 ページ ２００４年１月１５日　木曜日　午前１１時４７分

D. Mount the base unit on a wall

Standard wall plate mounting

This phone can be mounted on any
standard wall plate.

1) Locate the base unit on the wall
mount adapter as shown and slide
the wall mount adapter into the
notches on the base bottom with the
tab pressed.

2) Plug the AC adapter to the DC IN 9V
jack.

3) Route the AC adapter cord through
the molded wiring channel as shown.

4) Plug the AC adapter into a standard
120V AC wall outlet.

5) Plug the telephone line cord into the
TEL LINE jack. Route the cord
through the molded wiring channel
as shown.

1

2

3

4

5

6

7

7

GETTING STARTED

UP033BH_EXI7246C.book 10 ページ ２００４年１月１５日　木曜日　午前１１時４７分

Direct wall mounting

If you don't have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:

• Avoid electrical cables, pipes, or other items behind the mounting
location that could cause a hazard when inserting screws into the
wall.

• Try to mount your phone within 5 feet of a working phone jack to
avoid excessive cord lengths.

• Make sure the wall material is capable of supporting the weight of
the base and handset.

• Use #10 screws (minimum length of 1-3/8 inches) with anchoring
devices suitable for the wall material where the base unit will be
placed.

1) Insert two mounting screws into the wall, (with their appropriate anchoring device), 3-

15/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for
mounting the phone.

2) Refer to steps 1 through 7 on page 10 to mount the telephone.

GETTING STARTED

UP033BH_EXI7246C.book 11 ページ ２００４年１月１５日　木曜日　午前１１時４７分

Headset Installation

Your phone may be used with an optional headset, the Uniden HS910.
To use this feature, insert the headset plug into the headset jack.
Your phone is ready for hands-free conversations.
(Headset may be purchased by calling the Uniden Parts Department or
visiting the web site. See page 35.)

GETTING STARTED

UP033BH_EXI7246C.book 12 ページ ２００４年１月１５日　木曜日　午前１１時４７分

Basic Setup

There are five basic options that you will need to set up: AutoTalk, CIDCW (Caller ID on Call
Waiting), Area Code, Dial Mode and Language.

Activating AutoTalk

AutoTalk allows you to answer the phone simply by removing the handset from the base. You
do not have to press any keys.

1) When the phone is in standby mode, press and hold the caller id/

menu key. The following screen appears.

2) Press the select key to turn AutoTalk on.

3) Press the end key to complete the setting. The handset returns to standby mode.

Activating Caller ID on Call Waiting

Caller ID allows you to see the name and number of the calling party before you answer the
phone. Caller ID on Call Waiting (CIDCW) lets you see the name and number of a call that
comes in when you are on the line.

GETTING STARTED

UP033BH_EXI7246C.book 13 ページ ２００４年１月１５日　木曜日　午前１１時４７分