Uniden EXI4246C - EXI Cordless Phone, EXI4246 Series Owner's Manual
EXI 4246
QUICK REFERENCE GUIDE
EXI4246
Make sure your cordless phone's
packaging includes the following items.
Base Handset AC adapter
Belt Clip Rechargeable
battery
Telephone
cord
Also included: • Owner's manual
Plug the other end into the
telephone wall jack.
Plug one end of the
telephone cord into
the base TEL LINE
jack.
Step 2 Install Handset Battery Pack and Charge
Remove the
cover.
Connect the
battery pack
Note
Use ONLY the Uniden rechargeable battery pack supplied with
your new phone!
Step 1 Check the Package Contents
Plug the AC adapter cord to
the DC IN 9V jack (yellow) .
Plug the AC adapter to a
120V AC power outlet.
Route the cord.
Route the cord.
Route the cord.
Note
Use ONLY the Uniden AC adapter
supplied with your new phone!
Place the handset in
the base.
Make sure that
charge LED
Step 3 Set up the Base
Step 4 Charge the Handset
Step 5 Connect to the Phone Line
Step 6 Make & Receive Calls
To Make a Call
To Receive a Call
Press
talk/flash .
Listen for dial
tone.
Dial the desired
number.
Pick up the handset
and press talk/flash .
Additional Features
For more information on these and
other features, please refer to your
Owner's Manual. For your
convenience, listed below are
important features that will help
you set up your new cordless phone.
Refer to your Owner's Manual
Handset/Base Set up:
- Adjust the Earpiece
Volume → P.19
- Set the Ringer Volume → P.17
- Set Tone/Pulse Dialing → P.16
Caller ID:
Set Caller ID on Call Waiting
(CIDCW) → P.14
Note: You must subscribe to Caller
ID services through your local
telephone provider to use Caller
ID and CIDCW.
EXI4246
Asegúrese de que haya recibido los siguientes
artículos en el paquete
Base Receptor
Adaptador
CA
Pinza para
la correa
Pila
recargable
Cable
telefónico
Además
va incluido: • Manual del usuario
Conecte el otro extremo en el
enchufe telefónico de la pared.
Al enchufe telefónico
Cable de la línea telefónica
(suministrado)
Al enchufe TEL LINE
Conecte un
extremo de la
línea telefónica
en el enchufe
TEL LINE en la
base.
2° Paso
Instalación y carga de la pila para el receptor
Quite la tapa.
Conecte el
paquete de
Nota ¡Use SOLAMENTE el paquete de
pilas recargable de Uniden suministrado con su nuevo teléfono!
1° Paso
Inspección del contenido del embalaje
Conecte el adaptador CA en el
enchufe (amarillo)
DC IN 9V
.
Conecte el adaptador CA en
una toma de 120V CA.
Pase el cable
A la toma CA
Al enchufe DC IN 9V
Adaptador CA
(
suministrado
)
Nota ¡Use SOLAMENTE el adaptador CA de
Uniden suministrado con su teléfono!
Coloque el receptor
en la base.
Asegúrese de que el
LED de carga se
3° Paso Preparación de la base
4° Paso Carga del receptor
5° Paso Conexión de la línea telefónica
6° Paso Realización y recepción de llamadas
Para hacer una llamada
Para recibir una llamada
Oprima
talk/flash .
Espere por el tono
de marcación.
Marque el
número deseado.
Levante el receptor y
oprima
talk/flash .
Características adicionales
Para más información sobre estas y otras
características, le rogamos que consulte
su Manual del usuario. Para su
conveniencia, hemos listado abajo unas
características importantes, las cuales le
ayudarán a programar su nuevo teléfono
inalámbrico de Uniden.
Programación del receptor/base:
- Ajuste del volumen del auricular
y del altavoz → P. 19
- Programación del volumen del
timbre → P.17
- Programación de la marcación
por tono/pulso → P.16
Identificación de llamadas (Caller ID):
Programe la Identificación de llamadas
en Llamadas en espera (CIDCW)
→
P.1 4
Nota: Usted debe estar suscrito al
servicio de Identificación de llamadas con su proveedor de telefonía
local para poder usar las características de Caller ID y de CIDCW
Contents
QUICK REFERENCE GUIDE 1
Welcome/Features 4
Controls and Functions 5
Terms Used in this Manual 6
Accessibility 7
Installing the Phone 8
A. Choose the Best Location 8
B. Install the Rechargeable Battery Pack into the Handset 9
C. Connect the Base Unit and Charge the Handset 10
D. Mount the Base Unit on a Wall 11
Installing the Beltclip 12
Headset Installation 13
Basic Setup 14
Activating AutoTalk 14
Activating Caller ID on Call Waiting 14
Entering Your Area Code 15
Choosing the Dialing Mode 16
Setting the Language 16
Selecting the Ring Tone and Volume 17
Using Call Waiting 21
Voice Mail Waiting Indicator 22
Using the Speed Dial Memory 23
Storing Names and Numbers in Speed Dial Memory 23
Storing Caller ID Messages in Speed Dial Memory 26
Making Calls from Speed Dial Memory 27
Caller ID and CIDCW (Caller ID on Call
Waiting) 28
Viewing the Caller ID Message List 29
Deleting Information from the Caller ID List 30
Making a Call from the Caller ID List 31
Caller ID on Call Waiting (CIDCW) 31
Changing the Digital Security Code 32
Note on Power Sources 33
General Information 35
Troubleshooting 36
Liquid Damage 38
Precautions & Warranty 39
As an Energy Star Partner, Uniden has determined that this product or product
models meets the Energy Star
guidelines for energy efficiency.
Energy Star
is a U.S. registered mark.
Welcome
Features
• 2.4GHz Extended Range Technology
• Caller ID/Caller ID on Call Waiting
• 3-Line Backlit LCD
• Trilingual Menu Displays
• 30 Caller ID Memory
• 10 Number Memory Dialing
• Last Number Redial
• Tone/Pulse Dialing
•Find Handset Key
• Earpiece/Ringer Volume Controls
• Mute or Turn Ringer Off
• Hearing Aid Compatible
• 20 Channel Auto Scan
• Desk or Wall Mountable
If you have any trouble with your phone, call our Customer Hotline at 1-800-297-1023
Congratulations on your purchase of the Uniden cordless telephone. This phone is designed and
engineered to exacting standards for reliability, long life, and outstanding performance.
Note:Illustrations in this manual are used for explanation purposes. Some
illustrations in this manual may differ from the actual unit. The color of your
cordless phone may vary.
7
6
9
8
15
13
14
5
1
2
3
4
Controls and Functions
CONTROLS & FUNCTIONS
1. Handset antenna
2. Jack for optional headset
3. Beltclip hole
4. Ringer speaker
5. Handset battery compartment
6. Handset earpiece
7. LCD display
8. / /vol/ (earpiece volume, ringer
volume and scroll) key (pages 14, 17 and
19)
9. Call id/menu key (pages 14 and 28)
10.*/tone/ key (left cursor) key
(pages 20 and 23)
11. Redial/pause key (pages 19 and 25)
12. Select key (page 14)
13. Talk/flash key (pages 18 and 21)
14. End key (pages 18 and 19)
21
20
23
24
22
20. Base charging contacts
21. Find hs key (pages 21 and 32)
22. Charge/in use and VMWI
(Voice Mail Waiting Indicator) LED
23. DC IN 9V jack
24. Telephone line jack
Terms Used in this Manual
• Standby Mode - The handset may be sitting in or off the base, but is NOT in use. The talk/flash key has not
been pressed and there is no dial tone.
Accessibility
Uniden provides a customer service hotline for accessibility questions. If you have a disability and need customer
service assistance or if you have any questions about how Uniden's products accommodate persons with disabilities,
please call the accessibility voice/TTY line:
1-800-874-9314
A representative is available to talk to you M-F, 8:00 am to 5:00 pm, CST. After hours, you can leave a message, and
we will call you back. Information is also available on our web site, www.uniden.com, under the "Accessibility" link.
Installing the Phone
Do the following steps:
A. Choose the Best Location
B. Install the Rechargeable Battery Pack into the Handset
C. Connect the Base Unit and Charge the Handset
D. Mount the Base Unit on a Wall
A. Choose the Best Location
When choosing a location for your new phone, here are some important guidelines you should consider:
Avoid heat sources, such as radiators,
air ducts, and sunlight
Avoid television sets and other
electronic equipment
Choose a central location
Avo
id
noise sources such as a window by
a street with heavy traffic
Avoid microwave ovens
Avoid excessive moisture,
extremely low temperatures, dust,
mechanical vibration, or shock
Avoid personal computers
Avoid other cordless telephones
If your home has
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.
If you have questions
about what will disable
your alarm equipment,
contact your telephone
company or a qualified
installer.
note
INSTALLING THE
PHONE
B. Install the Rechargeable Battery Pack into the Handset
The handset is powered by a rechargeable battery pack.
The battery recharges automatically when the handset is placed
in the base unit.
1) Press down on the handset battery case cover (use the
finger indention for a better grip) and slide the cover
downward to remove.
2) Plug the battery pack connector (red & black wires) into the
jack inside the battery compartment.
(The connector notches fit into the grooves of the jack only
one way.) Match the wire colors to the polarity label in the
battery compartment, connect the battery and listen for a
click to insure connection.
3) Make sure you have a good connection by slightly pulling on
the battery wires. If the connection is secure, the battery
jack will remain in place.
Use only the Uniden
(BT-905) rechargeable
battery pack supplied
with your cordless
telephone.
!
INSTALLING THE
PHONE
C. Connect the Base Unit and Charge the Handset
1) Connect the AC adapter to the DC IN 9V jack and to
a standard 120V AC wall outlet.
2) Place the handset in the base unit with the keypad
facing forward.
3) Make sure the charge/in use LED illuminates.
If the LED does not illuminate, check to see that the AC
adapter is plugged in and the handset makes good
contact with the base charging contacts.
• Connect the AC adapter to a continuous power
supply.
• Place the base unit close to the AC outlet to
avoid long extension cords.
4) Charge your handset at least 15-20 hours before
plugging the phone line.
Route the cord.
Route the cord.
Route the cord.
•Use only the supplied
AD-0001 AC adapter.
Do not use any other
AC adapter.
•Do not place the power
cord where it creates a
trip hazard or where it
could become chafed
and create a fire or
electrical hazard.
!
INSTALLING THE
PHONE
D. Mount the Base Unit on a Wall
Standard wall plate mounting
This phone can be mounted on any
standard wall plate.
1) Plug the AC adapter to the DC IN 9V
jack.
2) Plug the AC adapter into a standard
120V AC wall outlet.
3) Plug the telephone line cord into the
TEL LINE jack.
4) Plug the telephone line cord into the
telephone outlet.
5) Align the mounting slots on the base
with the mounting posts on the wall.
Then push in and down until the
phone is firmly seated.
1
3
4
5
5
INSTALLING THE
PHONE
Direct wall mounting
If you don't have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting
location that could cause a hazard when inserting screws into the
wall.
• Try to mount your phone within 5 feet of a working phone jack to
avoid excessive cord lengths.
• Make sure the wall material is capable of supporting the weight of
the base and handset.
• Use #10 screws (minimum length of 1-3/8 inches) with anchoring
devices suitable for the wall material where the base unit will be
placed.
1) Insert two mounting screws into the wall, (with their appropriate anchoring device), 3-
15/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for
mounting the phone.
2) Refer to steps 1 through 5 on page 11 to mount the telephone.
INSTALLING THE
PHONE
Headset Installation
Your phone may be used with an optional headset. To use this feature,
insert the headset plug into the headset jack.
Your phone is ready for hands-free conversations.
(Headset may be purchased by calling Uniden's Customer Hotline or
visiting the web site. See page 35.)
INSTALLING THE
PHONE
Loading...