Uniden DECT 6035, DECT 6005 Owner's Manual

i

DECT 6005

Accessory handset for

DECT 6015 and DECT 6035 Series

DECT6005 OM.indd iDECT6005 OM.indd i 20/8/07 1:49:18 PM20/8/07 1:49:18 PM

1

Welcome

Congratulations on your purchase of the Uniden DECT6005
accessory handset and charger. You can place this fully featured
cordless handset anywhere your home has AC power.

Note: Illustrations in this manual are used for explanation

purposes. Some illustrations may differ from the actual unit.

Important!

The DECT6005 accessory handset will not operate until it is
registered to a Uniden main base. This manual describes how
to set up your new handset; for more detailed instructions on
operating your new handset, please refer to the manual supplied
with your base.

Terminology Used in this Manual

Base

The main part of the phone that connects to your phone
line, and lets you make and receive calls.

Charger

A cradle that charges an accessory handset. It connects to
power but not to a phone line.

Accessory
Handset

A handset that works with an expandable phone base.
Accessory handsets must be registered to a base.

Standby

The handset is not in use. If it is off the cradle, no line has
been activated. No dial tone is present.

Station Any handset or the base.

Talk

A telephone line has been activated on the handset or the
base, enabling a dial tone.

DECT6005 OM.indd 1DECT6005 OM.indd 1 20/8/07 1:49:19 PM20/8/07 1:49:19 PM

2

Compatible Bases

This handset is compatible with Uniden’s 1.8GHz DECT 6015
and DECT 6035 expandable phone series.

Installing the Accessory Handset

Checking the Package Contents

Make sure your package contains the following items. If any
items are missing or damaged, contact our Customer Service
Hotline. See inside the back cover page for contact information.

• Cordless Handset • Belt Clip

• Charger • Printed Material

• AC Adapter (model # AAD-600S: Input 240V AC, 50 Hz;
Output 9V DC, 210 mA)

• Rechargeable NiMH Battery Pack (model # BT-652: Capacity
650 mAh, 2.4V)

Installing the Battery

Follow the steps below to install the
rechargeable battery pack.

Using the fi nger indentation, press in on
the battery case cover and slide it down
to remove it.

Plug the battery connector into the
battery compartment jack. Be sure to
match the red and black wires to the
label near the jack.

Gently pull on the battery wires. If the
battery connector comes loose, try
connecting it again.

Replace the battery case cover and
slide it up until it clicks into place.

Note: Use only the Uniden BT-652

rechargeable battery pack supplied
with your cordless telephone.

1.

2.

3.

4.

DECT6005 OM.indd 2DECT6005 OM.indd 2 20/8/07 1:49:20 PM20/8/07 1:49:20 PM

3

Installing the Belt Clip

Line up the tabs with the holes on each side of
the handset. Press the belt clip down until both
tabs click into place.

To remove the belt clip, pull both sides of the clip
to release the tabs from the holes.

Installing the Optional Headset

Your phone may be used with an optional
headset. To use a headset, insert the headset
plug into the headset jack. Headsets may
be purchased by calling the Uniden Parts
Department. See inside the back cover page for
contact information.

Charging the Accessory Handset

The handset is powered by a rechargeable battery pack that
automatically recharges when the handset is placed in the
charger.

Connect the AC adapter to the DC IN 9V jack and to a 240V
AC outlet that is not controlled by a wall switch.

Caution: Use only the Uniden AAD-600S adapter.

Set the charger on a
desk or tabletop, and
place the handset in the
charger with the keypad
facing forward.

Make sure that the
charge LED illuminates.
If the LED does not
illuminate, check to see
that the AC adapter
is plugged in and
the handset makes
good contact with the
charging contacts on the charger.

Charge the handset battery pack for at least 15-20 hours
before using your new handset for the fi rst time.

1.

2.

3.

4.

To AC outlet

To DC IN 9V

AC adapter (supplied)

Route the cord.

Caution: Use only the Uniden AAD-600S adapter.

To AC outlet

To DC IN 9V

AC adapter (supplied)

Route the cord.

Caution: Use only the Uniden AAD-600S adapter.

DECT6005 OM.indd 3DECT6005 OM.indd 3 20/8/07 1:49:20 PM20/8/07 1:49:20 PM

4

Registering the Handset

You must register the handset to the base before you can use it.
Only one handset can be registered at a time. (If an accessory
handset has ever been registered to a base, you must reset the
handset before you can register it to a new base.)

To register to a DECT 6000
series base, place the
accessory handset in the base.
While the handset is registering,
HANDSET REGISTERING
appears in the LCD. When
REGISTRATION COMPLETE is
displayed, the handset has been
registered to the base.

If REGISTRATION FAILED
appears, pick up the handset
from the base and try again.

Resetting the Handset

If you want to register the handset to a different base or replace
a handset with another one, you must fi rst clear the registration
information from the base and the handset.

Press and hold [

] and [#] for at least fi ve seconds, until the

SYSTEM RESET menu appears.
Select the DEREGISTER HS

submenu by pressing [Menu/Select].
WHICH HANDSET? appears in the
display.

Use [

] or [ ] to select the handset ID to be de-registered
from the list, and then press [Menu/Select]. DEREGISTER
HS appears.

Press [ ] to move the cursor to YES, and then press
[Menu/Select]. You will hear a confi rmation tone.

1.

2.

3.

4.

Extra Handset

Extra Handset

Charger

Charger

Main Base

Extra Handset

+

Main Base

Charge the handset
for 15-20 hours.

Place the extra handset
in the main base to
register.

1

2

3

4

Registration
Complete.
Base #1

Extra Handset

Extra Handset

Charger

Charger

Main Base

Extra Handset

+

Main Base

Charge the handset
for 15-20 hours.

Place the extra handset
in the main base to
register.

1

2

3

4

Registration
Complete.
Base #1

Which Handset?
Handset #1
Handset #2

Which Handset?
Handset #1
Handset #2

DECT6005 OM.indd 4DECT6005 OM.indd 4 20/8/07 1:49:20 PM20/8/07 1:49:20 PM

5

Resetting the Handset Without the Base

If the original base this handset was registered to is not
available for some reason (for example, it is lost or somehow
incapacitated), you can still reset the handset and use it with
another base.

Press and hold [

] and [#] for more than fi ve seconds, until

the SYSTEM RESET menu appears.
Press [

] to move the cursor to BASE UNAVAILABLE and

then press [Menu/Select]. WHICH BASE? appears.
Press [

] to move the cursor to the base which you want
to de-register from, and then press [Menu/Select]. BASE
UNAVAILABLE appears.

Press [ ] to move the cursor to YES, and then press
[Menu/Select]. You hear a confi rmation tone, and the
handset deletes its own link to the base without trying to
contact the base.

Now you are ready to register the handset to the new base.

1.

2.

3.

4.

DECT6005 OM.indd 5DECT6005 OM.indd 5 20/8/07 1:49:21 PM20/8/07 1:49:21 PM