Uniden DCT748-4 Owner's Manual

DCT 748

SERIES

OWNER'S

MANUAL

Contents

WELCOME/FEATURES 2 TERMINOLOGY 3 CONTROLS & FUNCTIONS 4 DISPLAY AND ICONS 6 GETTING STARTED 7

Setting up the Phone 7 Expanding Your Phone 12 Register the Handset 14 Changing the Digital Security Code 15 Installing the Beltclip 15 Optional Headset Installation 15 Main Menu Options 16 Setting Menu Options 17

BASICS 26

Using Your Phone 26 Call Waiting 28 Placing a Call on Hold 28 Redialing a Call 29 Adjusting the Ringer, Earpiece and Speaker Volume 30 Mute Microphone 31 Tone Dialing Switch-over 32 Traveling Out of Range 32 Clarity Booster 33 Privacy Mode 33 Conferencing 34 Find Handset 34

PHONEBOOK 35

Setting up the Phonebook 35 Viewing the Phonebook 39 Making Calls Using the Phonebook 40 Speed Dialing 40 Editing or Erasing a Stored Name, Phone Number, Distinctive Ring and Speed Dial 41 Copying Phonebook Locations 42

CALLER ID 43

Caller ID and CIDCW (Caller ID on Call Waiting) 43

THE INTEGRATED TELEPHONE ANSWERING DEVICE 48

The Integrated Telephone Answering Device 48 Turning the Answering System On/Off 52 Setting Your Outgoing Message (Greeting) 52 Using Your Answering System 54 Remote Operation 58

MULTI-HANDSET FEATURES 62

Multi-Handset Features 62 Using DirectLink Mode 62 Intercom 64 Room/Baby Monitor 66

ADDITIONAL INFORMATION 67

Note on Power Sources 67 General Information 69

TROUBLESHOOTING 70

Troubleshooting 70 Liquid Damage 72

PRECAUTIONS & WARRANTY 73 I.C. NOTICE 75 INDEX 76 MEMORY LIST 77 REMOTE OPERATION CARD 80

[1]

www.uniden.com

Welcome

Features

Congratulations on your purchase of the Uniden Multi-Handset Cordless Telephone System! This unit is different from conventional cordless telephones. When the base unit is connected to AC power and a telephone line, it can support up to four handsets. You can now place a fully-featured cordless handset anywhere in your home or office where AC power is available to connect the handset chargers. Extra handsets also allow you to establish a three-way conference call among two handsets and an outside line.

Note: Illustrations in this manual are used for explanation purposes. Some

• Backward / Forward Compabibility

• 2.4GHz Frequency Hopping Spread Spectrum

• Integrated Answering Device

• 4 Multi-Handset Expandability (DCX700 handset sold separately)

• Handsfree Speakerphone

• Caller ID/Call Waiting Deluxe (subscribe through local telephone company)

• 100 Dynamic Memory Locations (Phonebook & Caller ID)

• Trilingual Display Options and Voice Prompts (English, French and Spanish)

• Intercom/Call Transfer Between Handsets

• Distinctive Ring Options

• 20 ring types - (10 ring tones and 10 melody rings)

• Hold or Mute Call

•Audio/Clarity Boost

• True Banner

• DirectLink Mode

• Room/Baby Monitoring

• Battery Level Indicator

• Clock Display

illustrations in this manual may differ from the actual unit.

As an Energy Star meets the Energy Star Energy Star



Partner, Uniden has determined that this product or product models



is a U.S. registered mark.

guidelines for energy efficiency.

FEATURES/

WELCOME/

www.uniden.com

WELCOME/FEATURES/TERMINOLOGY [2]

This series features AutoTalk and AutoStandby. AutoTalk allows you to answer a call by just removing the handset from the cradle so you don't have to waste time pushing buttons. AutoStandby allows you to hang up by simply returning the handset to the cradle.

To protect you against mis-billed calls that might result from your phone being activated by other equipment, this series has

Random Code digital security, which automatically selects one of about

130,000 digital security codes for the handset and base.

Digital Spread Spectrum Technology uses a wider frequency band than standard digital transmissions. The result is a more secure conversation with the clarity of digital sound, extended range, and minimal interference from other cordless phones.

IntegriSound Built in sound quality which provides life-like conversations. With DirectLink mode, you can use two or more handsets as radio transceivers (walkie-talkies).

Be sure to visit our web site: www.uniden.com



Uniden

is a registered trademark of Uniden America Corporation.

AutoTalk, AutoStandby, DirectLink, IntegriSound and Random Code are trademarks of Uniden America.

Your phone may be compatible with other Uniden 2.4GHz Digital Expandable System. Look for the technology icon on our boxes!

Terminology

•Standby Mode - The handset maybe sitting or off the cradle, but is NOT in use. talk/flash or has not been

pressed. No dial tone is present.

•Talk Mode - The handset is not in the cradle, and talk/flash or has been pressed and enabling a dial tone.

FEATURES/

WELCOME/

[3] WELCOME/FEATURES/TERMINOLOGY

www.uniden.com

Controls & Functions

11 12

1.Handset Antenna

2.Headset Jack Cover

3.Beltclip Hole

4.Speakerphone Speaker and Ringer

5.Handset Battery Compartment

6.New Message LED

7.Handset Earpiece

8.LCD Display

9. (ring)/vol (volume) and ∧/∨ ( P. 3 0 & 17 ) a.ringer and volume control b. scroll keys for display screen

10.cid (caller ID) (P. 45)

11.

15 16 17

/tone/ (P. 32 & 36)

12.pause/redial Key (P. 26 & 29)

13. (speaker) (P. 27)

14.talk/flash (P. 26 & 28)

15.menu/clear (P. 17 & 36)

16.select/ (Handset Remote)/audio tone (P. 17, 58 & 31)

17.end (P. 27)

18.#/ (P. 36)

19. (phonebook)(P. 35)

20.hold/transfer/int’com (intercom) (P. 28 & 64)

21.Handset Microphone

22.Handset Charging Contacts

CONTROLS &

FUNCTIONS

Repeat

Delete

www.uniden.com

Play

Skip

Stop

CONTROLS & FUNCTIONS [4]

24 25

27 28

29 30

31 32 33

353436

23. Base Speaker

24. charge LED

25. in use LED

26. Base antenna

27. New Message LED

28. (play/stop) (p.54)

29. find hs / (skip) (p.34 & 55)

30. (repeat)(p.55)

31. ∅ (delete)(p.56)

[5] CONTROLS & FUNCTIONS

32. volume/ (ring)/ (speaker) (p.30)

33. answer/on off LED (p.58)

34. Base Charging Contacts

35. TEL LINE Jack

36. DC IN 9V Jack

www.uniden.com

CONTROLS &

FUNCTIONS

Display and Icons

Example of the standby mode display

ࠕ1((

570# *CPFUGV 0GY%+&

ICON STATUS DESCRIPTION

Ringer off icon (when the ringer is off) / Day of the week and time / battery icon Handset ID and Banner Number of new Caller ID calls received

ࠕࠗ࠙

㨮

www.uniden.com

Standby/Talk

Standby Ringer off icon indicates that ringer is turned off.

Talk Mute icon appears when you mute the handset.

Talk Speaker icon appears when the handset speaker phone is used.

Talk Booster icon appears when the Clarity Booster feature is in use.

Talk Privacy icon appears when the Privacy Mode is turned on.

Talk Record icon appears while recording a conversation.

Battery icons indicate the handset battery status. This icon cycles depending on the battery status (full, medium, low, and empty).

DISPLAY AND ICONS [6]

DISPLAY AND ICONS

note

If your home has specially wired alarm equipment connected to phone line, be sure that installing the system does not disable your alarm equipment.

If you have questions about what will disable alarm equipment, contact your telephone company or a qualified installer.

GETTING STARTED

Setting up the Phone

Do the following steps:

A. Choose the best location B. Install the rechargeable battery pack into the handset C. Connect the base unit and charge the handset D. Mount the base unit on a wall

A. Choose the best location

Before choosing a location for your new phone, read "Installation Considerations" on page 74. Here are some important guidelines you should consider:

[7] GETTING STARTED

www.uniden.com

B. Install the rechargeable battery pack into the handset

The handset is powered by a rechargeable battery pack. The battery recharges automatically when the handset is placed in the base unit.

GETTING STARTED

note

1) Press down on the handset battery case cover (use the finger indention for a better grip) and slide the cover downward to remove.

2) Plug the battery connector (red & black wires) into the jack inside the battery compartment. (The connector notches fit into the grooves of the jack only one way). Match the wire colors to the polarity label in the battery compartment, connect the battery and listen for a click to insure connection.

3) Make sure you have a good connection by gently pulling on the battery wires. If the connection is secure, the battery jack will remain in place.

4) Place the battery case cover back on the handset and slide it upwards until it clicks into place.

www.uniden.com

•

Use only the Uniden (BT-446) rechargeable battery pack supplied with your cordless telephone.

•

Replacement battery packs are also available through the Uniden Parts Department at (800) 554-3988, Monday thru Friday from 8:00 a.m. to 5:00 p.m. or online at

www.uniden.com

GETTING STARTED [8]

note

•Use only the supplied AD-800 AC adapter. Do not use any other AC adapter.

•Do not place the power cord where it creates a trip hazard or where it could become chafed and create a fire or electrical hazard.

GETTING STARTED

C. Connect the base unit and charge the handset

1) Connect the AC adapter to the DC IN 9V jack and to a standard

120V AC wall outlet.

Note:

• Connect the AC adapter to a

continuous power supply (i.e., an outlet that is not controlled by a switch).

• Place the base unit close to the

AC outlet to avoid long extension cords.

2) Place the handset in the base unit with the keypad facing forward.

3) Make sure that the charge LED illuminates. If the LED does not illuminate, check to see that the AC adapter is plugged in and the handset makes good contact with the base charging contacts.

4) Charge your handset at least 15-20 hours before plugging into the phone line.

5) Once the handset battery pack is fully charged, connect the telephone line cords to the TEL LINE jack and to a telephone outlets.

If your telephone outlet isn't modular, contact your telephone company for assistance.

[9] GETTING STARTED

www.uniden.com

D. Mount the Base Unit on a Wall

Standard wall plate mounting

This phone can be mounted on any standard wall plate.

1) Plug the AC adapter into the DC IN 9V jack. Wrap

the AC adapter cord inside the molded wiring channel as shown.

2) Plug the AC adapter into a standard 120V AC wall outlet.

3) Plug the telephone line cords into the TEL LINE jack.

4) Plug the telephone line cords into the telephone outlets.

5) Align the mounting slots on the base with the mounting posts on the wall. Then push in and down until the phone is firmly seated.

GETTING STARTED

www.uniden.com

GETTING STARTED [10]

Direct wall mounting

If you don't have a standard wall plate, you can mount your phone directly to the wall. Before doing this, consider the following:

• Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.

• Try to mount your phone within 5 feet of a working phone jack to avoid excessive lengths.

• Make sure the wall material is capable of supporting the weight of the base and handset.

• Use #10 screws (minimum length of 1 & 3/8 inches) with anchoring devices suitable for the wall material where the base unit will be placed.

1) Insert two mounting screws into the wall

(with their appropriate anchoring device), 3 & 15/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for mounting the phone.

2) Refer to steps 1 through 5 on page 10 to

mount the telephone.

GETTING STARTED

[11] GETTING STARTED

www.uniden.com

Expanding Your Phone

Four Handset Expandability

Your phone supports up to four handsets, including any handsets supplied with your phone. You can now place a fully-featured cordless handset anywhere AC power is available to connect the handset charger. Handsets can be used in DirectLink Mode or on an intercom call without interfering with incoming calls. It is possible to have a three-way conference among two handsets and an outside lines. All of the handsets ring when a call is received.

Backward / Forward Compatibility

Your phone may be compatible with other Uniden 2.4 GHz Digital Expandable Systems. Please visit our website at www.uniden.com. If you purchase a DCX700 expansion handset, please register the handset to the original/main base before use. The DCX700 will not operate until it is registered.

GETTING STARTED

www.uniden.com

GETTING STARTED [12]

note

GETTING STARTED

Connect the expansion handset's charger

The handset is powered by a rechargeable battery pack. The battery recharges automatically when the handset is placed in the charger.

Use only the supplied AD-0005 AC adapter. Do not use any other AC adapter.

[13] GETTING STARTED

1) Connect the AC adapter to the DC IN 9V jack and to a

standard 120V AC wall outlet.

2) Set the charger on a desk or tabletop, and place the

handset in the charger with the keypad facing forward.

3) Make sure that the charge LED illuminates.

If the LED does not illuminate, check to see that the AC adapter is plugged in and the handset makes good contact with the base charging contacts.

4) Charge the handset battery pack for at least 15-20

hours before using your new cordless telephone for the first time.

www.uniden.com

If you purchase an expansion handset, you need to register the handset before use. Only one handset can be registered at a time.

Handsets supplied with the phone are registered to the base by the factory. When charged, pre-registered handsets display a handset ID number. Handsets that have not been registered display

registration or refer to Owner's Manual.

the base, the handset ID will be assigned.

For the DCX700 expansion handset

1) Before registering the extra handset, the battery pack MUST be charged for 15-20 hours.

2) Place the extra handset in the main base unit to begin registration.

3) While the handset is registering,

Registering Registration Complete

will appear in the LCD. When

been registered to the base. If appears, please try these steps again.

For the DCX640 expansion handset (DCT7 seriescompatible model)

1) Disconnect the AC adapter.

2) While holding find hs/ and on the base, connect the AC adapter. Keep pressing find hs/ and on the base until the CHARGE LED starts to blink.

3) On the handset, press and hold # until you hear beep.

www.uniden.com

Models vary! Charge handset on the base for

When you register an extra handset to

Handset

is displayed, the handset has

Registration Failed

GETTING STARTED [14]

GETTING STARTED

note

Your phone may be compatible with other Uniden 2.4GHz Digital Expandable Systems. Please visit our website at www.uniden.com for model number confirmation or call our customer service at (800) 297-1023.

Changing the Digital Security Code

The digital security code is an identification code used to connect the handset and the base unit. Normally, setting the code is not necessary. In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code. To change the digital security code:

1. Perform the "System Reset" options ("De-register the Handset" and "Replacing the Base Setting") for all the handsets you have (see page 25).

2. Re-register each handset by following the steps on page 14.

Installing the Beltclip

To attach the beltclip

Insert the beltclip into the holes on each side of the handset. Press down until it clicks.

To remove the beltclip

Pull either side of the beltclip to release the tabs from the holes.

Optional Headset Installation

Your phone may be used with an optional headset. To use this feature, insert the headset plug into the headset jack. Your phone is ready for hands-free conversations. (Headset may be purchased by calling the Uniden Parts Department or visiting the web site. See page 69.)

GETTING STARTED

[15] GETTING STARTED

www.uniden.com

Main Menu Options

Your phone has four main menu options: DirectLink Mode, Room/Baby Monitor, Handset Setup, Global Setup, and Answering Setup as well as submenu options.

Default Settings

The default settings set from the factory match the features that most people use. You may not need to change them. However, there are a number of options you must set and entries you must make in memory to take full advantage of all the phone features. The table below lists the default settings.

Function Handset Function Handset

Ringer Tones Distinctive Ring Auto Talk Anykey Answer Banner

Language (LCD) Key touch tone Security Code Ring Time

Flicker

Off

“ “

English

Toll Saver

Recording Time Message Alert Language (TAD) Call Screen Answer Setup Day & time CIDCW Area Code Dial Mode

one minute

Off

English

SUN 12:00 AM

CIDCW on/CWDX off

None

Tone

GETTING STARTED

note

For Global Setup and System Reset, when setting options from the handset, make sure the line is not in use and the handsets are within range of the base.

www.uniden.com

GETTING STARTED [16]

Setting Menu Options

Using the interface

Below are some tips for using the software interface on your phone.

GETTING STARTED

• Press menu/clear to access the main menu.

• Use /vol/∧ or /vol/∨ to scroll through options.

• Press select/ /audio tone to make a selection.

• Press menu/clear to cancel setting and exit the

menu.

• If you do not press a key within 30 seconds, the phone will time out and exit the

menu mode. When setting Day and Time, the time-out period is extended to two minutes.

[17] GETTING STARTED

&KTGEV.KPM/QFG 4QQO/QPKVQT *CPFUGV5GVWR

www.uniden.com

Handset Setup

The following submenu options must be set separately for each handset.

Selecting a Ringer Tone

Ringer tone lets you choose from 10 melodies or 10 ringer tones. You must set a separate ringer tone on each handset.

- Melodies (Beethoven's Symphony #9 [Beethoven9], For Elise [Elise], We Wish You A Merry Christmas [Merry- Xmas], Home Sweet Home [Hm Swt Hm], Lorri Song #6 [Lorri Song], When the Irish Eyes Are Smiling [Irish Eyes], Aura Lee, Let Me Call You Sweet Heart [Sweetheart], Star Spangled Banner [Star Spngl], Old MacDonald [Old MacDld])

- Ringers (Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder)

GETTING STARTED

1) Press menu/clear. Select the Handset Setup menu, and then the Ringer Tones submenu.

2) Press /vol/

∧ or /vol/∨ to move the pointer.

You will hear the ringer or melody as you scroll

4KPIGT6QPGU (NKEMGT %NCVVGT

through the options.

3) Press select/ /audio tone. You will hear a confirmation tone.

www.uniden.com

GETTING STARTED [18]

Distinctive Ringer Setup

Distinctive Ringer allows you to assign a designated ring tone to a stored phonebook number. When a call is received and the Caller ID information matches the information in one of the phonebook memory entries, the phone uses the distinctive ring assigned to that particular caller. You can assign distinctive rings to multiple phonebook memory entries. Switching the setting to Distinctive Off disables distinctive ringing: all incoming calls will have a normal ring tone. Switching to Distinctive On activates all programmed distinctive rings.

GETTING STARTED

1) Press menu/clear. Select the Handset Setup menu, and then the Distinctive Ring submenu.

2) Press /vol/

3) Press select/ /audio tone. You will hear a confirmation tone.

Setting AutoTalk

AutoTalk allows you to answer the phone simply by removing the handset from the cradle. You do not have to press any buttons to answer the call.

1) Press menu/clear. Select the Handset Setup menu, and then the AutoTalk submenu.

2) Press /vol/

3) Press select/ /audio tone. You will hear a confirmation tone.

[19] GETTING STARTED

∧ or /vol/∨ to select

Off

&KUVKPEVKXG4KPI

1P 1HH

#WVQ6CNM 1P 1HH

www.uniden.com

Setting Anykey Answer

GETTING STARTED

Anykey Answer allows you to answer the phone by pressing any number key,

/tone/ or #/ on the handset.

1) Press menu/clear. Select the Handset Setup menu, and then the Anykey Answer submenu.

2) Press /vol/

∧ or /vol/∨ to select

Off

3) Press select/ /audio tone. You will hear a

#P[MG[#PUYGT 1P 1HH

confirmation tone.

Setting the True Banner

True Banner lets you customize the name your handset displays. The name will be displayed on the LCD screen during Standby Mode, Intercom, Intercom Hold, Room Monitor, and Copy Phonebook operation. The banner name will be displayed on the receiving handset as well.

1) Press menu/clear. Select the Handset Setup menu, and then the Banner submenu.

2) Use the number keypad (0-9),

menu/clear to enter or edit the name.

/tone/ , #/ , or

$CPPGT /QOU2JQPG

AAAAAAAAAA

3) Press select/ /audio tone. You will hear a confirmation tone.

www.uniden.com

GETTING STARTED [20]

Selecting a Language

You can change the language the menu display will use. Choose from English, French, or Spanish.

GETTING STARTED

1) Press menu/clear. Select the Handset Setup menu, and then the Language submenu.

2) Press /vol/

Fran ﾕ ais

3) Press select/ /audio tone. You will hear a confirmation tone.

Setting the Key Touch Tone

Key Touch Tone is the tone your keypad makes when keys are pressed. You can turn this tone on or off.

1) Press menu/clear. Select the Handset Setup menu, and then the Key Touch Tone submenu.

2) Press /

3) Press confirmation tone.

[21] GETTING STARTED

∧ or /vol/∨ to choose

(French), or

Espaﾃol

(Spanish).

vol/∧ or /vol/∨ to select

English

select/ /audio tone. You will hear a

Off

.CPIWCIG

'PINKUJ (TCP㩟CKU

-G[6QWEJ6QPG 1P 1HH

www.uniden.com

Global Setup

If you change one of the global settings, you change that setting for all registered handsets. Only one handset can change global settings at a time.

Setting Day and Time

Day & Time sets the day and time of your display.

1) Press menu/clear. Select the Global Setup menu, and then the Day & Time submenu option.

2) Press /vol/

∧ or /vol/∨ to select the day of the

week, and then select/ /audio tone.

3) Press /vol/

∧ or /vol/∨ to set the hour, and then

press select/ /audio tone.

4) Press /vol/

∧ or /vol/∨ to set the minute, and then press

select/ /audio tone.

5) Press /

vol/∧ or /vol/∨ to choose

or PM, and then press

select/ /audio tone. You will hear a confirmation tone.

&C[6KOG 570#/ =㨬㨲㨱㨭5'.'%6?

GETTING STARTED

note

If no key is pressed for two minutes, the phone will exit the menu mode.

www.uniden.com

GETTING STARTED [22]

Setting Caller ID on Call Waiting (CIDCW)

Caller ID on Call Waiting (CIDCW) displays the name and number of an incoming call while you are on the line. Call Waiting Deluxe (CWDX) allows you to handle call waiting calls in seven different ways. See page 44 for instructions on using call waiting deluxe.

GETTING STARTED

1) Press menu/clear. Select the Global Setup menu, and then the CIDCW submenu.

2) Press /vol/

CW On/CWDX Off

3) Press select/ /audio tone. You will hear a confirmation tone.

Setting the Area Code

If you enter a 3-digit area code number in the "Area Code" option, your local area code does not appear in the Caller ID message. When calls are received from outside your local area code, you will see a full 10-digit number.

1) Press menu/clear. Select the Global Setup menu, and then the Area Code submenu.

2) Use the number keypad (0-9) to enter a 3-digit area code. If an area code has already been stored, it will appear in the display. Press menu/clear to delete the stored code, then enter a new one.

3) Press

[23] GETTING STARTED

%+&%9

∧ or /vol/∨ to select

, or

CW Off/CWDX Off

select/ /audio tone. You will hear a confirmation tone.

CW On/CWDX On

%91P%9&:1P

%91P%9&:1HH

#TGC%QFG 㨫AA

www.uniden.com

Setting the Dial Mode

Dial Mode sets the dial mode to tone or pulse. Most phone systems use tone dialing; the default setting is tone dialing. Set the dialing mode to match the dialing system used by your local phone service.

• If you are not sure of your dialing system, make a trial call. If the call connects, leave the setting as is; otherwise set the unit to pulse dialing.

• If your phone system requires pulse dialing and you need to send DTMF tones in certain situations during a call, you may switch over to tone dialing (refer to "Tone Dialing Switch-over" on page 32).

GETTING STARTED

1)Press menu/clear. Select the Global Setup menu, and

then the Dial Mode submenu.

2) Press /vol/

∧ or /vol/∨ to select

Tone

Pulse

(the initial setting is Tone).

3) Press select/ /audio tone. You will hear a confirmation tone.

www.uniden.com

&KCN/QFG 6QPG 2WNUG

GETTING STARTED [24]

System Reset

De-register the Handset

1) Press and hold end and #/ for more than 5 seconds. Select the Deregister HS submenu.

2) Press /vol/

∧ or /vol/∨ to select the handset

ID to be de-registered from the list, and then press select/ /audio tone.

3) Press

/vol/∧ or /vol/∨ to select

Deregister HS

appears.

Yes

, and then

press select/ /audio tone. You will hear a confirmation tone.

Replacing the Base Setting

1) Press and hold end and #/ for more than 5 seconds. Select the Replacing Base submenu.

Replace Base

2) Press

/vol/∧ or /vol/∨ to select

appears.

Yes

, and then

press select/ /audio tone. You will hear a confirmation tone. The base information will be deleted. When the base information is deleted, the handset displays

handset on the base for registration or refer to Owner's Manual

9JKEJ*CPFUGV! *CPFUGV *CPFUGV

>GIKUVGT*5 ;GU 0Q

4GRNCEG$CUG ;GU 0Q

Models vary! Charge

GETTING STARTED

[25] GETTING STARTED

www.uniden.com

+ 58 hidden pages