For more exciting new products please visit our website:
Australia: www.uniden.com.au
BW120
Baby Audio Monitoring System
2
IMPORTANT SAFETY INSTRUCTIONS
This manual contains important information about this
product’s operation. If you are installing this product for
others, you must leave this manual or a copy with the end
user.
When using your equipment, always follow basic safety
precautions to reduce the risk of re, electric shock and
injury to persons, including the following:
• This unit is NOT WATERPROOF. Never submerge the
devices in water or rinse them in running water.
• Always position the device and power cord out of
the reach of children. The power cord could result in
strangulation or cause injury to children.
• Keep small parts out of the reach of children (risk of
swallowing).
• Keep packaging material away from children (risk of
suffocation).
• Never place the baby unit in the cot or within the reach of
your child.
• Make sure that cables are out of the reach of your child
(risk of electric shock).
• Always make sure that the devices are fully functioning
before use, and that the batteries are sufciently charged
when in battery mode.
• Only use the AC adaptors included with the unit.
3
SAVE THESE INSTRUCTIONS!
• Do not use the cable to pull the AC adaptor plug out of
the socket.
• Disconnect the AC adaptor plug from the mains when the
device is not in use.
• The device and the AC adaptor should not come into
contact with hot surfaces or sharp objects.
• Do not use any additional parts that are not
recommended by the manufacturer or offered as
equipment.
• After use, before cleaning and changing any accessory
parts, the AC adaptor should always be disconnected.
• Batteries can contain toxins that are harmful to health
and the environment. Always dispose of batteries in
accordance with applicable legal regulations. Do not
dispose of batteries with normal household waste.
4
CONTENTS
WHAT’S IN THE BOX? ........................................................ 5
GETTING STARTED ............................................................ 6
Baby Unit...................................................................................................... 6
Parent Unit................................................................................................... 7
INSTALLATION .................................................................... 8
Baby Unit.........................................................................................................8
Parent Unit...................................................................................................... 9
TROUBLESHOOTING ....................................................... 10
SPECIFICATIONS ..............................................................12
WARRANTY .......................................................................13
5
WhAT’S IN ThE BOX?
• If any item is missing or damaged, contact your place of
purchase immediately. Never use damaged products!
• Need help? Get answers at our website:
www.uniden.com.au for Australian model
BW120 Parent Unit
BW120 Baby Unit
• AC Adaptors (x2)
• NiMH Rechargeable Batteries for the Parent Unit (x2)
• Owner’s Manual
Not Pictured:
6
GETTING STARTED
Baby Unit
1
Power LED - Lights up to indicate the unit has been
powered on.
2
Power ON/OFF button - Press and hold to turn on/off
the unit.
3
Microphone - Receives sounds for the area near the
Baby Unit, and transmits the sound to the Parent Unit.
4
Power Jack (rear) - Connect to the AC adaptor.
1
2
3
4
7
Parent Unit
1
2
3
3
4
5
6
7
1 Sound level light display - Lights up to indicate the
sound intensity.
2 Power LED - Lights up to indicate the unit has been
powered on.
3 Volume Up/Volume Down button - You can adjust the
volume in 5 levels on the unit by pressing the buttons.
4 Power ON/OFF button - Press and hold to turn on/off
the unit.
5 Power jack (underneath) - Connect to the AC adaptor.
6 Speaker - Produces the sound transmitted from the
Baby Unit.
7 Battery compartment
8
INSTALLATION
The Baby Unit powers on with
the AC adaptor.
1. Insert the AC adaptor
power plug into the Baby
Unit’s DC socket (at the
back of the unit).
2. Connect the other end into
a 240 volt AC (standard
indoor) power outlet.
Once the Baby Unit is connected to power, it automatically
turns on and the Power LED glows green.
To power off the unit, press and hold the Power button. To
power on the unit again, press and hold the Power button.
Baby Unit
9
Parent Unit
• The Parent Unit is designed in such a way that it can be
operated only with batteries inserted.
• The battery must be charged for at least 16 hours
before the unit can be rst used independently of the AC
adaptor. You may use the unit during this time.
To switch on the Parent Unit again, press and hold the
Power button. The Power LED of the Parent Unit will light up
green to indicate that the device is active.
If the Parent Unit battery is low, the unit will beep twice.
If the device is not connected to a socket, it will switch off
automatically after a short period.
The Power LED will turn off.
Operation
Connect the AC adaptor on the Parent Unit (with batteries
included) to a socket. The device automatically switches on,
and the Power LED will light up green.
If the AC adaptor is unplugged, the unit will switch to battery
operation. The standby time will depend on the battery
charge status.
To switch the unit off, press and hold the Power button, and
the Power LED will turn off.
Points to note when installing the Parent Unit:
10
TROUBLEShOOTING
Problems Possible Solutions
Power LED does not
light up after switchon.
Check to ensure that:
• the AC adaptor is properly
plugged in.
• the batteries are full. Check if
the rechargeable battery needs
charging or is damaged (Parent
Unit).
An acoustic signal
sounds from the
parent unit.
Check to ensure if:
• the maximum range has been
exceeded
• the AC adaptor for the baby unit
is properly connected
• the Baby Unit is switched on
• the batteries are full. Check if
the rechargeable battery needs
charging or is damaged (Parent
Unit).
No acoustic signal
sounds from the
parent unit.
Adjust the volume on the Parent
Unit.
The device switches
off automatically.
Replace the batteries or recharge
the battery (Parent Unit).
11
The signal is weak,
the connection keeps
breaking up or there
is interference.
• If another technical device such
as a microwave is in the area
between the Parent and Baby
Units, remove the device or switch
it off.
• Check whether other factors
(such as trees etc) are in the path
of the two devices, and change
the position of the devices until the
Parent Unit signals a connection.
• Check whether both the units are
inside their respective receiving
ranges.
12
SPECIfICATIONS
Radio Frequency DECT technology
Frequency 1.8GHz frequency
No. of Channels 120 digital channels
Unobstructed
Effective Range
300m
Power Supply Baby Unit: (6 V DC/450 mA)
Parent Unit:
NiMH battery (2 x 1.2 V/400 mAh) and
supplied AC Adaptor (6 V DC/450 mA)
Operating
Temperature
5ºC to 45ºC
Battery (Parent Unit) 15 hours standby
Dimensions Baby Unit: 95 x 36 mm,
Parent Unit: 90 x 45 mm
Approx. Weight Baby Unit: 48g
Parent Unit:100g, (with batteries)
13
IMPORTANT: Satisfactory evidence of the original purchase is required
for warranty service
Please refer to our Uniden website for any details or warranty durations
offered in addition to those contained below.
Warrantor: The warrantor is Uniden Australia Pty Limited ABN 58 001 865
498.
Terms of Warranty: Uniden Aust warrants to the original retail purchaser
only that the BW120 (“the Product”), will be free from defects in materials and
craftsmanship for the duration of the warranty period, subject to the limitations
and exclusions set out below.
Warranty period: This warranty to the original retail purchaser is only valid
in the original country of purchase for a Product rst purchased either in
Australia or New Zealand and will expire one (1) year from the date of the
original retail sale.
If a warranty claim is made, this warranty will not apply if the Product is found
by Uniden to be:
(A) Damaged or not maintained in a reasonable manner or as
recommended in the relevant Uniden Owner’s Manual;
(B) Modied, altered or used as part of any conversion kits, subassemblies
or any congurations not sold by Uniden Aust;
(C) Improperly installed contrary to instructions contained in the relevant
Owner’s Manual
(D) Repaired by someone other than an authorized Uniden Repair Agent in
relation to a defect or malfunction covered by this warranty; or
(E) Used in conjunction with any equipment, parts or a system not
manufactured by Uniden.
Parts Covered: This warranty covers the Product and included accessories.
User-generated Data: This warranty does not cover any claimed loss of
or damage to user-generated data (including but without limitation phone
numbers, addresses and images) that may be stored on your Product.
WARRANTY
14
Statement of Remedy: If the Product is found not to conform to this warranty
as stated above, the Warrantor, at its discretion, will either repair the defect
or replace the Product without any charge for parts or service. This warranty
does not include any reimbursement or payment of any consequential
damages claimed to arise from a Product’s failure to comply with the
warranty.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
This warranty is in addition to and sits alongside your rights under either the
COMPETITION AND CONSUMER ACT 2010 (Australia) or the CONSUMER
GUARANTEES ACT (New Zealand) as the case may be, none of which can
be excluded.
Procedure for obtaining warranty service: Depending on the country in
which the Product was rst purchased, if you believe that your Product does
not conform with this warranty, you should deliver the Product, together with
satisfactory evidence of your original purchase (such as a legible copy of
the sales docket) to Uniden. Please refer to the Uniden website for address
details.
You should contact Uniden regarding any compensation that may
be payable for your expenses incurred in making a warranty claim. Prior
to delivery, we recommend that you make a backup copy of any phone
numbers, images or other data stored on your Product, in case it is lost or
damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD
Phone: 1300 366 895
Email: custservice@uniden.com.au
15
16
©2016 Uniden Australia Pty Ltd
Printed in PRC
Loading...