Uniden BT230 User Manual
BT230 Bluetooth®
Headset User’s Guide
Also in this package:
AC (indoor) power adapter 2 extra ear cushions
Questions? Problems? Get help on the web at www.uniden.com
or call our Customer Service line at 800-292-2294.
CONTENTS
GETTING TO KNOW THE
HEADSET .............................. 3
What the LED Colors Mean ....... 3
What the Buttons Do ................. 5
SETTING UP YOUR
HEADSET .............................. 6
Charge the Battery .................... 6
Pair the Headset to Your
Bluetooth Phone ................... 7
Connect to Your Phone ............. 8
Once the Headset is Paired ...... 8
USING YOUR HEADSET ........ 9
Put your headset on .................. 9
Wearing the Headset
on Your Left Ear .................... 10
2
FEATURES ............................ 10
Basic .........................................10
Call Waiting .............................. 11
Voice-Activated Dialing .......... 11
USING THE MULTIPOINT
FUNCTION ......................... 12
Pairing to More than
One Phone ............................ 12
Using Both Phones .................. 12
TROUBLESHOOTING AND
MAINTENANCE .................. 13
Reset the Headset ...................14
GETTING TO KNOW THE HEADSET
Ear
hook
Volume
Multi-
function
button
(
MFB
)
LED
Ear
cushion
Microphone
ON slide
Down
Up
Power
Connector
Ear
hook
Volume
Multifunction
button
(
MFB
)
LED
Ear
cushion
Microphone
ON slide
Down
Up
Power
Connector
WARNING: Using the headset at excessive volume can
cause permanent hearing loss. To reduce
the risk of hearing damage, use the
minimum volume level necessary (see page
13).
* Specications and features are subject to change
without notice.
What the LED Colors Mean
Color State Meaning
Red
Steady
Flashing If the headset is also beeping, the battery is low.
The headset is currently charging. When the battery is fully
charged, the LED turns o.
3
Color State Meaning
3 ashes The headset is turned on.
1 ash every 5 seconds The headset is in standby & not paired to a Bluetooth device.
2 ashes every 5
Blue
seconds
3 ashes every 5
seconds
Red &
Alternating ash The headset is in pairing mode.
blue
* Specications and features are subject to change without notice.
The headset is currently paired to a Bluetooth device.
The headset is on an active call.
What the Tones Mean
Tone Meaning
Melody Depending on the melody, the sound indicates one of the following:
Power on
-
Power o
-
Incoming call
-
Low battery
-
4
Tone Meaning
2 Rising Beeps Active call
2 Falling Beeps Ending a Call
3 Short Beeps Successfully paired with a mobile phone
What the Buttons Do
The headset initiates the function only after the button is released.
Press it to
Multifunction button (MFB)
In standby: Redial the most recently
dialed number.
During an incoming call: Answer the call.
During a call: Hang up.
Press & hold it for
2 seconds to 4 seconds to
In standby: Activate voice dialing.
During an incoming call: Reject the call.
During a call: Transfer the call to your
phone (or back).
In standby:
Put the
headset
into pairing
mode.
5
Press it to
Press & hold it for
2 seconds to 4 seconds to
Volume Up
During a call: Increase
the call volume.
NA
During a call-waiting call: Put the active
call on hold and switch to the waiting call.
Volume Down
During a call: Decrease
the call volume.
NA NA
SETTING UP YOUR HEADSET
Charge the Battery
Before using your headset, charge the battery until the red LED turns o (about 2 hours).
►
Charging the battery completely (and keeping it charged) will help you get the longest possible
talk and standby time out of the battery.
Connect the adapter to the power connector on the side of the headset, then plug it into any
►
standard 120 V AC (regular indoor) power outlet.
6
Loading...