Uniden BLUETOOTH XDECT R035BT, XDECT R035, XDECT R035BT+1, XDECT R035BT+2, XDECT R035BT+3 Owner's Manual

...

Download

For more exciting new products please visit our website:

Australia: www.uniden.com.au

New Zealand: www.uniden.co.nz

XDECT R035

Bluetooth

XDECT R035BT base with answering system and cordless handset

Battery cover

XDECT R003BT accessory

handset and charger

(with stand)

If you purchased model number:

You should

have: XDECT R035BT None XDECT R035BT+1 1 of each XDECT R035BT+2 2 of each

XDECT R035BT+3 3 of each XDECT R035BT+4 4 of each XDECT R035BT+5 5 of each

You will also nd:

Rechargeable battery (BT-694s)

If any items are missing or damaged, contact your place of purchase. Never use damaged products!

Need Help? Get answers at our website: www.uniden.com.au for Australian model or www.uniden.co.nz for New Zealand model.

XDECT R035BT Series Owner’s Manual

What's in the box?

Telephone cord

AC adapter

(AAD-041S(M))

Rechargeable battery pack

(BT-694s)

Charger AC adapter (AAD-041S(M))

Battery cover

IMPORTANT SAFETY INSTRUCTIONS!

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

This unit is NOT waterproof. DO NOT expose this unit to rain or moisture. x Do not use this product near water, for example, near a bath tub, wash bowl, x

kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak.

Use only the power cord and batteries indicated in this manual. x Do not dispose of batteries in a fire. They may explode. Check with local codes x

for possible special disposal instructions. Do not place the handset in any charging cradle without the battery installed

and the battery cover securely in place.

SAVE THESE INSTRUCTIONS! #

What’s in the manual?

Geng Started ............................ 1

Installing Your Phone .................. 1

Seng Up the MobileLink

Bluetooth™ Connecon ........... 2

Installing the Repeater/Charger(s)

(if included) ................................. 5

Using the Repeater ..................... 6

Understanding Your Phone .......... 9

Using the Menus ....................... 14

Using Your Phone ...................... 17

Learning the Basics ................... 17

Using Caller ID and Redial Lists . 19

Using the Phonebook ............... 20

Finding a Lost Handset .............. 22

Using Mul-Handset Features . . 22

Using Special Features .............. 24

Using the Answering System ..... 25

Answering System Opons (

Ans.

Setup

)..................................... 25

Accessing the Answering

System .................................... 26

Personalizing Your Greeng ..... 27

Geng Your Messages ............. 28

Screening Your Calls.................. 29

Using the System While You’re

Away from Home ................... 29

Important Informaon .............. 31

Solving Problems ...................... 31

Reseng and Registering

Handsets ................................ 36

Registering Repeaters ............... 37

AC Adapter and Baery

Informaon ............................ 39

Index ......................................... 40

Warranty ................................... 42

CAUTION! Risk of explosion if battery is replaced by an incorrect type! Dispose of used batteries according to the instructions. Do not open or mutilate the battery. Disconnect the battery before shipping this product.

For more details, see the Important Information section.

GETTING STARTED

Installing Your Phone

Charge the baery

Unpack all handsets, batteries, and 1. battery covers. If you need to remove a battery cover, press in on the notch and slide the cover down.

Line up the battery connector with the jack inside the handset and 2. push the connector in until it clicks into place. Tug gently on the wires to make sure the battery pack is securely connected.

Replace the cover and slide it up into place.3. Connect the base AC adapter to the 4.

DC IN 9V

jack on the base. Run

the cord through the indent and out the back. If you have accessory handsets, connect each charger’s AC adapter 5.

to the

Power Jack

and run the cord though the indent. (See page 5

for the repeater/chargers.) Plug the other end of each adapter into a standard 240V AC power 6.

outlet. Place one handset in the base and the other(s) in the charger(s) 7.

with the display(s) facing forward. The display on the handset should light up; if it doesn’t, reseat the handset or try plugging the AC adapter into a different outlet.

Charge all handsets completely (about 15 hours) before using #

them.

Connect the telephone cord

Connect the

TEL LINE

jack to a standard telephone wall jack.

Test the connecon

Pick up the handset from the cradle and press 1.

TALK/FLASH

. You

should hear a dial tone, and the display should say

Talk

If you don't hear a dial tone or the display says

Check Tel Line

, try checking the connection between the base and the phone jack.

Make a quick test call. (Press 2.

END

to hang up.)

If there's a lot of noise or static on the call, see page 33 for tips

on avoiding interference.

Test any accessory handsets the same way. If you can’t get a dial 3. tone or the handset display says

Unavailable

, try resetting the

handset (see page 36).

Seng Up the MobileLink Bluetooth™ Connecon

The new XDECT R035BT with MobileLink technology can connect with Bluetooth phones supporting Bluetooth V2.0 handsfree profile. The following phones have been tested with this feature (see our website for the most up to date list of tested phones):

Apple

x HTC x LG x

Motorola x Nokia x Palm x RIM x Samsung x Sony Ericsson x

Visit our website for more information on compatible models.

If you are not certain of the profiles supported by your Bluetooth

phone or if you have difficulty pairing your phone to the XDECT R035BT, see the manual that came with your phone.

With the MobileLink feature, you can essentially treat your cellular

phone as a second line. You can use the XDECT R035BT handset to make and receive calls on your cellular phone number, put cellular calls on hold, and transfer calls to other handsets. See page 17 for more information.

Bluetooth wireless devices have a maximum range of 3m; the

actual range will vary depending on local conditions (obstacles, battery power, interference, etc.).

Pair your Bluetooth phone

Pairing “introduces” two Bluetooth devices and gives them permission to connect to each other. In most cases, once you pair a phone to the XDECT R035BT, the two devices connect automatically whenever they detect each other. (If you have to manually reconnect each time, check the Bluetooth settings on your cellular phone.)

With the XDECT R035BT in standby, press and hold 1.

BLUETOOTH

MOBILELINK

on the base until the Bluetooth icon begins to flash

(about 2 seconds). On your Bluetooth phone, start a search for other Bluetooth 2.

devices. (This process may take several seconds, and it will be different for each mobile phone; see your phone’s owner’s manual for detailed instructions.)

Your phone should discover a device called a 3.

XDECT R035BT

or a

Handsfree device

. When your phone asks if you want to pair with

this device, answer yes. If your phone prompts you for a PIN code or password to pair 4.

with the XDECT R035BT, enter

0000

(four zeroes).

When your phone accepts the Bluetooth connection, the XDECT

R035BT sounds a confirmation tone and the Bluetooth LED on the base remains lit. You’ll also see the Bluetooth status icon display on the handset.

Most cellular phones automatically transfer the audio to a x

Bluetooth device as soon as it pairs; if yours does not, look in your phone's Bluetooth setup for a "transfer audio" or "send audio to device" option.

To test the connecon

Pick up the handset from the cradle.1. Dial the number you want to call, then press 2.

LINK

twice on the handset. You may not hear a dial tone or ringing, but the handset display says

Talk

Make sure the call connects and you can hear clearly. (When 3. you’re finished, press

END

to hang up.)

The XDECT R035BT remembers the pairing information for

your cellular; if it loses connection with your phone for any reason (e.g., the cellular phone travels out of range, runs out of charge, etc.), the XDECT R035BT can automatically reconnect the next time your phone becomes available.

Using the XDECT R035BT with two Bluetooth phones

The XDECT R035BT can save the pairing information for two x

different Bluetooth phones, but it can only use one cellular line at any given time. For example, if you pair the XDECT R035BT to two Bluetooth phones, when you press

LINK

on the handset, the XDECT

R035BT asks which phone you want to connect to. If you are using the XDECT R035BT to talk on one Bluetooth

phone, the XDECT R035BT will not ring if a call comes in on the second phone.

You can set a different ring tone for each paired cellular phone

(see page 15). To pair a second Bluetooth phone, just repeat the pairing

procedure with the second phone. (If the first phone interferes when you’re pairing the second, just turn off Bluetooth on the first phone until you finish pairing the second one.)

Installing the Repeater/Charger(s) (if included)

Connect the repeater/charger power cord

1. If your phone came with any accessory handsets and chargers, connect a charger AC adapter to each charger's

DC IN 9V

jack and set the plug into the notch as shown. (These adapters might already be connected.)

Plug the other end of the adapter 2. into a standard 240V AC power outlet.

Aach the stand

To attach the stand, you have to decide if you want the repeater to 3. rest on a desk or hang on a wall. For desktop use, turn the stand so the locking tabs that say

DESK

are facing the base with the arrows pointing up. OR For wall mount use, turn the stand so the locking tabs that say

WALL

are facing the base with the arrows pointing down. Align the stand with the notches on the repeater.4. Slide the stand onto the notches until it clicks into place. (To 5.

remove the stand, pull the locking tabs up and back. Then, slide the stand straight off the same direction you put it on.)

Place the repeater/charger on the wall

For wall mount use, place the mounting slots (hole spacing is 6. 30mm horizontal) over the pins on the wall, and slide the base down to lock it into place.

To place a Repeater/Charger

Make sure you have a strong signal from the base (at least 3 bars x

in the handset display). Put the charger at least 10m away from the base or any other

Repeater/Charger. (If you put the charger on a different floor from the base, don't forget to allow 10m vertically, also.)

Using the Repeater

How it works

An XDECT R003BT repeater can extend the range of your base in all directions, including up and down. The XDECT R003BT repeater unit is also a charger for the accessory handset.

Each handset will automatically connect to the repeater or the base, depending on which signal is stronger, and the handset operates exactly the same way whether it's connected to the base or to the repeater.

The repeaters must be registered to the base before you can use them. Any repeaters that come packaged with the base are already registered to that base. For instructions on registering repeaters to the base, see page 37.

Note: Base range (grey area) and repeater range (dotted outline around repeater) is represented here as circular. Actual coverage area will vary depending on environment.

Your base supports a total of six XDECT R003BT repeaters, including any that were supplied with your phone.

Base coverage area

(The base signal is stronger; handsets

in this area connect

to the base.)

(Handsets in this area can

connect to either unit.)

(Minimum separation distance)

Handset

Repeater coverage area

(The repeater signal is

stronger; handsets in

this area connect to

the repeater. )

10m

Base

Repeater

Repeaters can be up to 3 chain-links (maximum) from the base

Example of coverage area with 6 repeaters (maximum total)

You can roam anywhere within range of the base or the repeater(s) and make and receive calls as usual from your handsets.

If you want to use the repeater with a new base, simply register

the repeater to the new base (see page 37). The repeater overwrites its own link to the base.

Placing repeaters

Here are a few tips for placing your repeater so that you get the clearest signal and the maximum range:

Make sure you have good reception from the base

For best performance put the repeater at least 10m away from x

the base or any other repeater. (If you install the repeater on a different floor from the base, don't forget to allow 10m vertically, also).

If possible, mount the repeater on the wall.

Picking the best spot

The best spot for the repeater is as far from the base as possible while still maintaining a good signal, or near the edge of the base’s coverage area. To find the edge of the coverage area:

Stand near the base 1. and make a call on the handset.

While on the call, 2. carry the handset away from the base towards the general area where you want to put the repeater.

Watch the signal 3. strength icon on the handset. Make a note where the icon drops from 4 bars to 3 bars.

Continue walking away from the base. Make a note where the 4. signal strength icon drops from 3 bars to 2 or if you start to hear noise on the line (which indicates the signal is getting weaker).

Place the repeater anywhere inside the range where the signal 5. strength icon showed 3 bars and the handset had a clear signal with no noise.

Tesng the locaon

Connect the repeater's AC adapter and make sure the

LINK

light comes on and steady. If the light flashes, the repeater is not getting a good signal. The repeater may be too far away from the base, there may be interference from electronic devices, or the signal might be blocked by thick walls or metal objects. Try moving the repeater to another location.

UNDERSTANDING YOUR PHONE

Parts of the base

MESSAGE COUNTER

REV

DOWN

FWD

FIND

Charging

contacts

DELETEPLAY/

STOP

DO NOT

DISTURB

ON/OFF

BLUETOOTH

CELLLINK

Base keys and how they work

Key name (and icon) What it does

FIND

In standby: page all handsets to find a lost one.

DO NOT DISTURB

In standby: turn the Do Not Disturb feature on or off (see page 24).

ON/OFF

In standby: turn the answering system on or off.

REV

(

)

While a message is playing: for the first 2 seconds, go to the previous message; after that: go to the start of this message.

MOBILELINK

DND

Bluetooth

Antenna (not shown)

Key name (and icon) What it does

PLAY/STOP

( )

In standby: start playing messages. While a message is playing: stop playing -

messages. While the phone is ringing: mute the -

ringer for this call only.

FWD

( )

While a message is playing: skip to the next message.

DELETE

(

)

While a message is playing: delete this message.

In standby, delete all messages. While Bluetooth phone is ringing: reject -

the call.

DOWN

(–)

In standby: decrease the ringer volume. While a message is playing: decrease the -

speaker volume.

UP (+

)

In standby: increase the ringer volume. While a message is playing: increase the -

speaker volume.

BLUETOOTH MOBILELINK

( )

In standby: pair your Bluetooth phone to the base (see page 3).

Parts of the handset

Microphone

Twelvekey dial pad

Visual ringer

Display

Charging

contacts

Earpiece

PHONEBOOK/

LEFT

SPEAKER

DOWN

CID/RIGHT

REDIAL/

PAUSE

MESSAGES/ MUTE

CLEAR/

INTERCOM

LINK

END

TALK/

FLASH

MENU/ SELECT

Handset keys and how they work

Key name (and icon) What it does

( )

In standby: increase the ringer volume. During a call: increase the call volume. In the menu or any list: move the cursor -

up one line.

CID/RIGHT

( )

In standby or during a call: open the Caller ID list.

During text entry: move the cursor to the right.

Key name (and icon) What it does

/ LOCK( )

In standby: press and hold to lock or

unlock the keypad.

DOWN

( )

In standby: decrease the ringer volume. During a call: decrease the call volume. In the menu or any list: move the cursor -

down one line.

MENU/SELECT

In standby: open the menu. In the menu or any list: select the -

highlighted item.

END

( )

During a call: hang up. In the menu or any list: exit and go to -

standby.

CLEAR/INTERCOM

In standby: page another handset using the intercom.

During a call: put the call on hold and start a call transfer.

While entering text: delete one character, or press and hold to delete all the characters.

PHONEBOOK/LEFT

( )

In standby or during a call: open the phonebook.

In a menu: go back to the previous screen.

During text entry: move the cursor to the left.

TALK/FLASH

( )

In standby: start a telephone call on your land line (get a dial tone).

While the land line is ringing: answer the incoming call.

During a call: switch to a waiting call. -

SPEAKER

( )

Switch a call to the speakerphone (and back).

Key name (and icon) What it does

REDIAL/PAUSE

In standby: open the redial list. While entering a phone number: insert a -

2-second pause.

LINK

(

)

In standby: start a telephone call using your paired Bluetooth phone.

While the Bluetooth phone is ringing: answer the incoming call.

During a MobileLink call: switch to a waiting call.

(See page 3 for information on pairing your Bluetooth phone.)

MESSAGES/MUTE

( )

In standby: access your answering system.

During a call: mute the microphone. While the phone is ringing: mute the -

ringer for this call only.

Display icons and what they mean

Since the icons appear based on what you’re doing with the phone, you won’t ever see all of these icons at the same time.

Icon What it means

The ringer is turned off: this handset will not ring when a call comes in.

You have a voice message waiting (see page 25).

Privacy Mode is on: no other handset can join your

call.

The speakerphone is on.

The microphone is muted, and the caller can’t hear

you.

Icon What it means

T-coil mode is on (see page 34).

The battery is 1) empty, 2) getting low, 3) half charged, or 4) fully charged.

The signal from the base is 1) weak, 2) low, 3) strong, or 4) very strong.

[Aa] The handset enters capital letters first (see page 16).

[aA]

The handset enters lower-case letters first (see page

16).

There is a cellular phone paired to MobileLink slot #1, #2, or both. (When the paired Bluetooth phone

is ringing, on a call, or on hold, the slot number for the paired phone blinks.)

Using the Menus

Handset Setup Ans. Setup Day & Time

To open the menu, press

MENU/SELECT.

Press MENU/SELECT to choose the highlighted option

press END to exit the menu

To go back a screen, press

PHONEBOOK/LEFT

The cursor

shows the

highlighted

option.

To move the

cursor, use

UP & DOWN.

<HANDSET SETUP> T-coil Ringer Tones

If you open the menu during a call, use x

PHONEBOOK/LEFT

to back

out of the menu without hanging up. If you don't press any keys for 30 seconds, the handset exits the

menu.

The Handset Setup Menu

You can change these settings separately for each handset.

T-coil

Turn on T-coil mode to reduce noise on some hearing aids (see page 34).

Ringer Tones

You can set a different ring tone for the land line and each paired cellular phone. First, select the line you want to set the ring tone for. Then, select the ring tone that you want this handset to use for that line.

As you highlight each ring tone, the phone plays a

sample. When you hear the tone you want, press

MENU/SELECT

Personal Ring

Turn on the personal ring feature. This feature lets you assign special ring tones to people in the cordless

phone’s local phonebook. When someone in your

phonebook calls, this handset uses the assigned ring

tone. (It doesn’t matter what line the person calls on,

as long as you have Caller ID service on that line.) Banner Change the name used on the handset’s display. Key Touch Tone Have the keypad sound a tone when you press a key.

The Ans. Setup menu

This menu controls the options and settings for your answering system (see page 25).

The Day and Time menu

If you subscribe to Caller ID, the phone automatically sets the day and time when it receives Caller ID information from your phone company. If you want to set the clock manually, just open the menu

and select

Day and Time

. The phone prompts you to select the day,

enter the time, and select

AM/PM

. (When prompted for the time, use

the number keypad to enter 2 digits for the hour and 2 digits for the minutes, e.g., 0530 for 5:30).

The Global Setup menu

The settings on this menu affect all handsets and the base. Before changing these settings, make sure the phone is in standby and all handsets are within range of the base. (Only one handset at a time can change these settings.)

Set Line Mode

Do not change this setting unless instructed to by customer service.

Insert 0

This feature adds “0” or “00” at the beginning of the number received from Caller ID. The default setting for New Zealand is ON. The default setting for Australia is OFF.

VMWI Reset

Reset the message waiting indicator if it gets out of sync with your voice mail service (see page 25).

How to enter text on your phone

Use the 12-key dial pad when you want to enter text into your phone (a name in the phonebook, the handset banner, etc.).

The phone defaults to a capital letter for the first letter and any

letter after a space; otherwise, it uses small letters. To switch to all capital letters, press

. The phone defaults to all capital letters first (e. g. ABCabc2) until you enter a blank space or press

again. (Any time you want to change case, just press *.)

If two letters in a row use the same number key, enter the first

letter and wait a few seconds (or press

RIGHT

); the cursor will

move to the next space. Enter the next letter. Press

to enter a blank space.

To change a letter, move the cursor to that letter and press

CLEAR

to erase the letter; enter the new one. To erase the entire entry, press and hold

CLEAR

Press

to cycle through all available symbols and punctuation.

USING YOUR PHONE

You can control the features in this section through the handset.

Learning the Basics

To... From the land line

From the cell phone

make a call: Dial the number, then

Press

TALK/FLASH

SPEAKER

Press

LINK

twice.*

answer a call

Press

TALK/FLASH

SPEAKER

Press

LINK

hang up Press

END

or put the handset in the cradle.

mute the microphone during a call

Press

MESSAGES/MUTE

. Press again to turn the

microphone back on.

put a call on hold

Press

CLEAR/INTERCOM

. After 5 minutes on

hold, the call will be disconnected.

return to a call on hold

Press

TALK/FLASH

SPEAKER

Press

LINK

switch from one line to the other (automatic hold)

Press

LINK

.* The handset automatically puts the landline on hold and connects to the cell phone.

Press

TALK/FLASH

. The handset automatically puts

the MobileLink line

on hold and connects to the land line.

switch between the speakerphone and earpiece

Press

SPEAKER

mute the ringer for this call only

While the phone is ringing, press

MESSAGES/

MUTE

on the handset or

PLAY/STOP

on the

base.

* If you have two cellular phones paired, the phone prompts you

to choose one. Select the phone you want, press

MENU/SELECT

, and

press

LINK

again.

Change the volume

Speaker and earpiece volume Ringer volume

You can change the volume of the speaker on the base and each cordless handset separately.

You can change the volume of the earpiece on each handset; this does

not affect the handset’s speaker

volume. Anytime you are listening to a -

speaker or earpiece, press

increase the volume and

DOWN

decrease it.

You can change volume of the ringer on the base and each handset separately.

Each cordless handset uses the same ringer volume for both the land line and the cellular line.

When the phone is in standby, press

increase the volume and

DOWN

to decrease it.

If you turn the ringer volume all the way down, the ringer turns off.

Call Waing

Call Waiting is a service available from your telephone provider that lets you receive calls while you are on another call. Caller ID on Call Waiting (CIDCW) service displays Caller ID information for a waiting call. You might have to subscribe to these services separately for your landline and your cellular phones. Contact your telephone provider(s) for more information.

When you get a Call Waiting call, the phone sounds a tone and displays any CID information received for the waiting call.

For Australian Model:

Press

TALK/FLASH

on the handset and then press 2 to accept the waiting call. The first caller is put on hold, and you will hear the new caller after a short pause. To return to the original caller, press

TALK/FLASH

and then 2 again.

For New Zealand Model:

Press

TALK/FLASH

on the handset to accept the waiting call. The first caller is put on hold, and you will hear the new caller after a short pause. To return to the original caller, press

TALK/FLASH

again.

For Mobile Phone Calls:

When you receive a call waiting call while on a mobile phone call press

LINK

to switch between mobile phone calls (for calls to the same

mobile phone only).

Using Caller ID and Redial Lists

Caller ID (CID) is a service available from your telephone provider that shows the phone number (and sometimes the caller’s name) of incoming calls. You might have to subscribe to CID service separately for your landline and your cellular phones. Contact your telephone provider(s) for more information.

On MobileLink calls, you might see the name of your cellular #

phone in place of the caller’s name.

Caller ID List Redial List

The phone saves the information for the last 30 -

received calls to the CID list. Landline calls and MobileLink calls are saved to the same CID list.

The CID list is shared by all cordless handsets. New records have an asterisk next to the received time.

When the phone’s in standby, each handset shows how many calls came in since the last time you checked the CID list.

Only one handset can access the CID list at a time.

Each cordless handset remembers the last 5 numbers you dialed on it.

The redial list is separate for each handset, however, only one handset can access the redial list at a time.

The handset doesn’t record which line was used to call the number.

To… Follow these steps…

Open the CID list Press

CID/RIGHT

Open the Redial list Press

REDIAL/PAUSE.

Scroll through the list

Press

DOWN

to scroll through the list from

newest to oldest. Press

to scroll from

oldest to newest.

Dial a number

Highlight the number you want and press

TALK/FLASH

(or

LINK

twice*).

Close the list Press

PHONEBOOK/LEFT

* If you have two cellular phones paired, the phone prompts you

to choose one. Select the phone you want, press

MENU/SELECT

, and

press

LINK

again.

To select a number, highlight the number and press

MENU/SELECT

. The

phone gives you the following options:

Delete Entry Erase the number from the list.

Store Into Pb

Add the number to the phonebook. The handset prompts you to edit the name and number and select a personal ring.

Delete All

(Caller ID list only.) Erase all numbers from the list. (This does not affect the CID lists on the paired cellular phones.)

Using the Phonebook

The phone can store up to 70 entries in its central phonebook; the x

phonebook is shared by all cordless handsets. The phonebook is separate from any contact lists on the paired

cellular phones: no changes you make in the phonebook will affect your cellular phone's contact list.

Only one handset can access the phonebook at a time.

To do this... Do this...

Open/close the phonebook

Press

PHONEBOOK/LEFT

Scroll through the entries

Press

DOWN

to scroll through the phonebook

from A to Z or Up to scroll from Z to A.

Jump to entries that start with a certain letter

Press the number key corresponding to the

letter you want to jump to.

Dial an entry

Find the entry you want to dial, and press

TALK/FLASH

(or

LINK

twice*).

* If you have two cellular phones paired, the phone prompts you

to choose one. Select the phone you want, press

MENU/SELECT

, and

press

LINK

again.

To select a number, highlight the number and press

MENU/SELECT

. The

phone gives you the following options:

Edit

Edit this entry. The handset prompts you to edit the name and number and select a personal ring.

Delete Erase this entry.

Phonebook menu opons

With the phone in standby, open the phonebook. From the main phonebook screen (instead of an individual entry), press

MENU/SELECT

The phone gives you the following options:

Create New

Add an entry to your phonebook. The handset prompts you to enter a name and number and select a personal ring.

Delete All Erase all the entries in the phonebook.

Finding a Lost Handset

With the phone in standby, press

FIND

on the base. All the handsets will

beep for 1 minute; to end the page, press

FIND

again or press any key

on any handset.

Using Mul-Handset Features

To use the features in this section, you must have at least two cordless handsets.

Expanding your phone

Your base supports a total of six cordless handsets: the one that x

came with the base and up to five XDECT R003BT accessory handsets.

Your base might be compatible with other Uniden accessory

handsets: please visit our website for a list of compatible handsets. Accessory handsets must be registered to the base before you can

use them. Handsets that aren't registered display a

Handset not

registered

message. For instructions on registering handsets to

the base, see page 36, or consult the accessory handset manual. Any accessory handsets that came packaged with the base are

already registered for you. If a handset was previously registered to a base, you have to reset

it so you can register it to a new base (see page 36 or the manual for the accessory handset).

Conference calling

When an outside call comes in on the land line, two handsets can x

join in a conference call with the outside caller. To join an ongoing call, press

TALK/FLASH

SPEAKER

To leave the conference call, hang up normally; the other handset

remains connected to the call.

Privacy mode

You can prevent other handsets from joining a call. Start your call as usual, then press

MENU/SELECT

: the display shows

Call Privacy

Press

MENU/SELECT

again to turn privacy mode on (you’ll see in the

display). When you hang up, privacy mode turns off automatically.

As long you have privacy mode on, no other handsets can interrupt your call. To allow another handset to join the call, press

MENU/SELECT

twice to turn privacy mode off.

Call transfer

To… On the land line

Using MobileLink

transfer a call

Press

CLEAR/INTERCOM

, then select the handset you want to transfer the call to (select

All

to page all the handsets). When

the other handset accepts the call, you’ll be

disconnected.

cancel a transfer: and leave the call on

hold

Press

END.

and return to the call Press

TALK/FLASH

. Press

LINK

answer a call transfer page

Press 1.

CLEAR/INTERCOM

. You can speak to

the transferring handset. To speak to the outside caller, 2.

press

TALK/FLASH

press

LINK

Intercom

Whenever the phone is in standby, you can make an intercom call x

between handsets without using the phone line. You can make an intercom call from any handset, but only two

handsets can be in an intercom call at any time. If an outside call comes in during an intercom page, the phone

sounds a tone and shows any received CID information. If another handset hasn't answered the page yet, the phone cancels the page to let you can answer the incoming call.

To... Follow these steps:

make an intercom page

Press

CLEAR/INTERCOM

, then select the handset you want to talk with (select All to page all handsets at the same time).

cancel a page Press

END

answer an intercom page Press

CLEAR/INTERCOM

TALK/FLASH

leave an intercom call Press

END

answer an outside call during an intercom call

Press

TALK/FLASH

LINK

(depending on which line is ringing). The phone automatically disconnects the intercom call and connects you to the outside line.

Using Special Features

Do Not Disturb (DND)

The Do Not Disturb feature (DND) turns off the ringers on the base x

and all handsets at the same time. You can turn on DND from the base whenever the phone is in

standby: just press and hold

DO NOT DISTURB

for about a second. The phone automatically turns on the answering system and shows

Do Not Disturb

on all handsets.

To turn DND off, press

DO NOT DISTURB

again.

If you turn the answering system off while DND is on, the phone

turns off DND along with the answering system.

Chain dialing

If you often have to enter a series of digits or a code number x

during a call, you can save that code number to a phonebook entry and use the phonebook to send the code number.

Enter the code number (up to 20 digits) into the phonebook just

like a regular phonebook entry. Be sure to enter the code number into the phonebook exactly as you would enter it during a call.

When you hear the prompt that tells you to enter the number,

open the phonebook and find the entry that contains your code

number. Press

MENU/SELECT

to transmit the code. Or, if you change

your mind, use

PHONEBOOK/LEFT

to close the phonebook.

Voice message nocaon

This feature supports Frequency-Shift Keying (FSK) message x

notification. Contact your voice mail provider for more details. If you subscribe to a voice mail service, your phone can notify you

when you have a new message waiting.

When you have new messages, the voice message icon (

x )

appears in the display, and the light at the top of the handset blinks.

The voice message icon should disappear after you listen to all

your new messages. If it doesn’t, you can reset it manually: With the phone in standby, open the menu and select

Global Setup

Select

VMWI Reset

, then select

Yes

USING THE ANSWERING SYSTEM

The answering system works with land line calls only and provides up to 15 minutes of total record time. The system will not answer or take messages on incoming call on the paired Bluetooth phones.

Answering System Opons (Ans. Setup)

You can change the answering system options from any handset. Just open the menu and select

Ans. Setup

. Select one of the following:

Security Code

Enter a 2-digit PIN so you can access your answering system from any touch-tone phone (see page 29).

Ring Time

Set the number of rings (6, 9, or 12) before the answering system answers the phone. Choose Toll Saver to have the system answer after 2 rings if you have new messages or after 4 rings if

you don’t.

Record Time

Set the amount of time callers have to leave a message, either 1 minute or 4 minutes. Choose

Announce Only if you don’t want the system to

let callers to leave a message.

Message Alert

Have the system beep every 15 seconds when

you have a new message; the beeping stops when you listen to all your new messages. (To mute the alert without listening to your messages, press any key on the base.)

Call Screen

Turn on the call screen feature so you can hear callers as they leave messages on the base speaker (see page 29).

Ans. On/off

Turn your answering system on or off. (To turn

your system on or off from the base, just press

ON/OFF

Accessing the Answering System

You can access your system from a handset whenever the phone is in standby.

5:Stop [ / /select]

Press

MESSAGES/

MUTE

to start remote

operation mode.

Press

MENU/SELECT

to choose the displayed option.

Press

END

to exit

remote operation

mode.

4:Delete 3:Skip 2:Play 1:Repeat

6:SelectGreeting 8:RecNewGreeting

Use

PHONEBOOK/

LEFT

to go to the

previous option:

Use

CALLER ID/

RIGHT

to go to

the next option:

During remote operation, the phone beeps to let you know it's x

waiting for your next command.

You can press the number key next to the commands instead of x

scrolling through them. If you don't press any keys for 30 seconds, the phone returns to

standby. Only one handset can access the system at a time, and you can't

access the system while another handset is on a land line or MobileLink call.

Personalizing Your Greeng

Your greeting can be between 2 seconds and 30 seconds long. If you don’t record an outgoing message, the system uses a pre-recorded greeting: Hello, no one is available to take your call. Please leave a message after the tone.

Record your personal outgoing message or greeng

Access the system from any handset. Wait until the system 1. finishes its announcements, or press

(

Stop

) to skip them.

Press 2.

(

RecNewGreeting

Wait for the system to say “Record greeting,” then begin speaking.3.

When you’re finished, press 4.

(

RecNewGreeting

) to recording.

The system plays back your new greeting.

To keep this greeting, press 5.

END

. To re-record it, go back to step 2.

Switch between the two greengs

Access the system from any handset. Wait until the system 1. finishes its announcements, or press 5 (

Stop

) to skip them.

Press 2.

(

SelectGreeting

) to play back the current greeting.

Press 3.

(

SelectGreeting

) again to switch greetings.

Delete your greeng

Switch to your personal greeting following the steps above. While the system is playing back your greeting, press

(

Delete

Geng Your Messages

To… From the base

From a handset (remote operation)

play new messages

Press

PLAY/STOP

Press

MESSAGES/

MUTE

The system announces the number of new and old messages, then plays each new message (followed by the time and date) in the order it was received.

replay an earlier message

Within the first 2 seconds of a message,

press

REV.

select 1:Repeat.

restart the current message

Wait at least 3 seconds after

the message starts, then press

REV

Wait at least 5

seconds after the message starts, then select

1:Repeat.

skip a message Press

FWD

. Select 3:Skip.

delete a message

While the message is playing,

press

DELETE

While the

message is playing, select

4:Delete.

delete all of your messages

With the phone in standby,

press

DELETE

. When the system

asks you to confirm, press

DELETE

again.

Not available.

play old messages

After the system plays the new messages,

press

PLAY/STOP

again. Select 2:Play.

stop playback Press

PLAY/STOP

. Select 5:Stop.

Screening Your Calls

Another feature your answering system gives you is call screening. While the system is taking a message, you can hear the caller on the base speaker (if you turn on Call Screen) or from a handset. Only one handset at a time can screen calls. If another handset is screening the call, the handset beeps and returns to standby.

To... From the base From a handset

hear the caller leaving a message

Just listen to the caller over the speaker.

Press

MESSAGES/MUTE

answer the call Not available. Press

TALK/FLASH

mute the call screen without answering

Press

PLAY/STOP

Press

END

or return the

handset to the cradle.

If you mute the call screen, the system continues

taking the message: it just stops playing through

the speaker.

Using the System While You’re Away from Home

You can also use your answering system from any touch-tone phone. Before you can use this feature, you must program a security code.

Programming a security code

With the phone in standby, open the menu from any handset.1.

Select 2.

Ans. Setup

, then select

Security Code

Use the number keypad to enter a two-digit security code (00 to 3.

99). Press

MENU/SELECT

when you’re finished.

Remember to make a note of your new security code! #

Dialing in to your system

Call your telephone number and wait for the system to answer. 1.

If you have the

Ring Time

set to

Toll Saver

, the system answers after 2 rings if you have new messages and 4 rings if you don’t. You can hang up during the third or fourth ring.

If your answering system is off, it will answer after about 15 x

rings and sound a series of beeps instead of your greeting.

During the greeting (or beeps), press 2.

and

immediately

enter your security code. (If you enter it incorrectly 3 times, the system hangs up and returns to standby.)

The system announces the current time, the number of messages 3. stored in memory, and a help prompt. Then it starts beeping intermittently to let you know it's waiting for your command.

When you hear the intermittent beeping, enter a command from 4. the chart:

#1 Repeat message #5 Stop playback #2 Play message #6 Turn on #3 Skip message #9 Turn off #4 Delete message #0 Hear prompts

If you don’t press any keys for 15 seconds, the phone will #

hang up and return to standby.

IMPORTANT INFORMATION

Solving Problems

If you have any trouble with your phone, try these simple steps first. If you need help, visit the Customer Support page on our website; www. uniden.com.au for Australia or www.uniden.co.nz for New Zealand.

If… Try…

No handsets can make or receive calls.

Checking the telephone cord connection. Disconnecting the base AC adapter. Wait a -

few minutes, then reconnect it. Making sure the base is plugged in. -

A handset can’t make or

receive calls.

Moving the handset closer to the base.

A handset can make

calls, but it won’t ring.

Making sure the ringer is turned on. Making sure Do Not Disturb is turned off. -

A handset is not working.

Charging the battery for 15-20 hours. Checking the battery connection. Resetting the handset. -

A handset says

Unavailable.

Moving the handset closer to the base. Seeing if another handset is in Privacy -

Mode.

No handsets display Caller ID information.

Letting calls ring twice before answering. Making sure your Caller ID service is active. -

Caller ID displays briefly and then clears.

You may have to change the line mode. Contact customer service.

I can’t transfer calls. Resetting all handsets. Two handsets can’t talk

to the caller.

Making sure no handset is in Privacy Mode.

The answering system does not work.

Making sure the answering system is on. Making sure the base is plugged in. -

If… Try…

The system won’t record

messages.

Making sure the Record Time is not set to Announce Only.

Deleting messages (memory may be full). Making sure the call was on the land line -

(the system cannot answer MobileLink

calls).

A handset can’t access

the answering system.

Seeing if another handset is using the system.

Making sure the phone is in standby. -

The XDECT R035BT

won’t pair with my

phone.

Making sure your phone is in pairing mode. Check your phone’s manual for instructions -

on Bluetooth device pairing. Making sure your phone supports the -

Bluetooth handsfree profile.

The XDECT R035BT

doesn’t ring when my

cellular phone does.

Making sure your phone has Bluetooth turned on.

Making sure your phone is in range of the base.

Making sure the handset’s ringer is not turned off. (The base doesn’t ring on cellular

calls.)

The XDECT R035BT paired with my phone,

but I can’t hear anything

through the handset.

Adjusting the handset volume. Setting your cellular phone to transfer -

the audio to a Bluetooth device. Check

your phone’s manual for instructions on

Bluetooth setup and options. Erase the Bluetooth pairing and repair -

the cellphone to the base. Press and hold

MOBILELINK

for 10 seconds. The base beeps and the Bluetooth pairing information is erased from the base (if 2 cellular phones are paired, both pairings are deleted).

If… Try…

I can’t get my handset to

switch to the repeater.

Re-registering the repeater. Making sure the repeater and handset are -

registered to the same base.

The

LINK

light on the repeater randomly starts blinking.

Moving the repeater closer to the base. -

Weak or hard to hear audio

If a caller’s voice sounds weak or soft, the signal might be blocked by large metal objects or walls; you might also be too far from the base, or the handset’s battery may be weak.

Try moving around while you’re on a call or moving closer to the

base to see if the sound gets louder. Make sure the handset’s battery is fully charged.

Try adjusting the earpiece volume. x

Noise or stac on the line

Interference is the most common cause of noise or static on a cordless phone. Here are some common sources of interference:

electrical appliances, especially microwave ovens

computer equipment, especially wireless LAN equipment and DSL x

modems radio-based wireless devices, such as room monitors, wireless

controllers, or wireless headphones or speakers fluorescent light fixtures (especially if they give off a buzzing

noise) other services that use your phone line, like alarm systems,

intercom systems, or broadband Internet service

If static is on 1 handset or in 1 location:

If static is on all handsets or in all locations:

Check nearby for one of the common interference sources.

Try moving the handset away from a suspected source, or try moving the suspected

source so it’s not between the

handset and the base. There is always more noise at -

the edges of the base’s range.

If an

Out of Range

message displays, try moving closer to the base.

Check near the base for the source of interference.

Try moving the base away from a suspected source, or turn off the source if possible.

If the base has an adjustable antenna, try raising the antenna so it stands straight up.

If you have any service that uses the phone line, you might need a filter (see below).

Installing a line lter or DSL lter

Sometimes, broadband Internet services that use the telephone line



static on telephones. A DSL filter or telephone line filter usually solves this problem. The technician who installed your DSL service might have left some filters for you; if not, call your DSL provider or look in any electronics store.

Plug the DSL filter into the telephone wall jack and plug your phone’s base into the filter. Make a test call to make sure the noise is gone.

Do you use a T-Coil hearing aid?

If you have a hearing aid equipped with a telecoil (T-coil) feature, the interaction between the hearing aid and digital cordless phones can cause noise in the handset. If you have a T-coil hearing aid and you have

problems with noise on the line, try turning on

T-coil

mode. Open the

menu. Select

Handset Setup,

then select

T-coil

Using T-coil mode can shorten the handset’s talk time; make sure to watch the battery status and keep the battery charged.

Liquid damage

Moisture and liquid can damage your cordless phone. If the exterior housing of the handset or base is exposed to moisture or liquid, wipe off the liquid, and use as normal. If moisture or liquid is inside the plastic housing (i.e. liquid can be heard in the phone or liquid has entered the handset battery compartment or vent openings on the base), follow these steps:

Handset Base

Remove the battery cover and disconnect the battery.

Let dry for at least 3 days with the battery disconnected and the cover off for ventilation.

After the handset dries, reconnect the battery and replace the cover. Recharge the battery fully before using.

Disconnect the AC adapter to cut off the power.

Disconnect the telephone cord.

Let dry for at least 3 days before reconnecting.

CAUTION! DO NOT use a microwave oven to speed up the #

drying process. This will cause permanent damage to the handset, base and the microwave oven.

Reseng and Registering Handsets

If you are having trouble with a cordless handset or if you want to replace one, you need to clear the registration information from the base and the handset:

Do you have the base the handset is registered to? Yes No

Press and hold 1.

END

and # until the System Reset menu appears (about 5 seconds).

Select 2. Deregister HS. The display lists all registered handsets.

Select the handset you want to reset.3. When the handset asks you to 4.

confirm, select Yes. The handset clears its information from the base and deletes its own link to the base.

Press and hold 1.

END

and # until the System Reset menu appears

(about 5 seconds). Select 2. Base

Unavailable. When the handset 3.

asks you to confirm, select Yes. The handset deletes its own link without contacting the base.

Registering a handset

When you reset a handset (or if you buy a new one), that handset displays a

Handset Not Registered

message. If you see this message

on a handset, you need to register it to a base before you can use it.

Does the handset fit in the base cradle? Yes No

Place the handset in the base. The display should say Handset Registering.

With the phone in standby, 1. press and hold

FIND

on the

base for about 5 seconds. On the handset you want 2.

to register, press and hold

until the display says Handset Registering (about 2 seconds).

In about 30 seconds, the handset display should say

Registration

Complete

. Press

TALK/FLASH

and make sure you get a dial tone.

If... Try...

- you don’t hear a dial tone

- the display says Registration Failed

Making sure the handset is fully charged, then starting over at step 1.

Registering Repeaters

If you are having trouble with a repeater or if you want to replace one, you need to register the repeater to the base.

TIP: Connect the repeater close to the base for easy access to the necessary keys and indicators. Locate the repeater in the desired position after registration is complete.

On the base, press and hold 1.

FIND

when the phone is in

standby.

On the bottom of the repeater 2. you want to register, press and hold the registration button until the

LINK

light blinks

rapidly.

In about 90 seconds, the 3. LINK light on the repeater will turn on. The repeater has been registered to the base.

If the LINK light doesn't turn on, try these steps again.

- Only register one repeater at a time. If more than one repeater is in registration mode at the same time then they can interfere with each other.

- Only register a repeater to one base at a time. If more than one base is in registration mode at the same time then you can't control which base the repeater registers to.

AC Adapter and Baery Informaon

Use only the supplied AC adapters. Be sure to use the proper x

adapter for the base and any chargers. Do not place the power cord where it creates a trip hazard or

where it could become chafed and create a fire or electrical hazard. Do not place the unit in direct sunlight or subject it to high

temperatures. Fully charged, the battery should provide about 10 hours of talk

time and about 7 days of standby time. For best results, return the handset to the cradle after each call to keep it fully charged.

When the battery gets too low, the handset shows a low battery

alert. If you hear a strange beep during a call, check the display: if you see the low battery alert, finish your conversation as quickly as possible and return the handset to the cradle. If the handset is in standby, none of the keys will operate.

With normal use, the battery should last about one year. Replace

the battery when the talk time becomes short even when the battery is charged. To buy a replacement battery, visit our website; www.uniden.com.au for Australia or www.uniden.co.nz for New Zealand.

Rechargeable Nickel-Metal-Hydride Baery Warning

This equipment contains a rechargeable Nickel-Metal-Hydride battery.  The rechargeable batteries contained in this equipment may explode if 



Do not short-circuit the battery.  Do not charge the rechargeable battery pack used in this equipment in any 



in the owner's manual. Using another charger may damage the battery pack or cause the battery pack to explode.

Rechargeable Batteries Must Be Recycled or Disposed of Properly. Uniden works to reduce lead content in PVC coated cords in our

products & accessories.

INDEX

Answering a Call ...................17

Answering System ................25

Base Unavailable ..................36

Baery Install ........................1

Baery Informaon ..............39

Bluetooth........................2, 3, 4

Caller ID ................................19

Call Waing ..........................18

Conferencing ........................22

Controls & Parts of the Phone . .

....................................9, 11

Day and Time ........................15

Deleng a Redial Record ......20

Deleng Caller ID Numbers . . 20 Deleng Phonebook Entries . 21

Deregistraon ......................36

Do Not Disturb .....................24

Earpiece Volume ............11, 18

Entering Text from the Phone . .

........................................16

Finding a handset .................22

Handset Banner ....................15

Hanging up ...........................17

Insert 0 .................................16

Installing the Phone ................1

Intercom ...............................23

Key Touch Tone ....................15

Keypad Lock..........................12

Liquid Damage ......................35

Low Baery Alert ..................39

Making a call ........................17

Making a call from a Caller ID

Record .............................20

Message Alert ...................... 26

Mung the Microphone .......17

Mung the Ringer ................17

Out of Range ........................34

Personal Ring ........................15

Phonebook .....................16, 20

Placing a Call on Hold ...........17

Privacy Mode ........................22

Redialing a Number ..............19

Repeaters ...............................6

Reseng the Handset ..........36

Ringer Tones .........................15

Ringer Volume ..........10, 11, 18

Screening calls ................26, 29

Security Code .................25, 29

Speaker Volume .......10, 11, 18

T-coil ........................14, 15, 34

Talk and Standby Times .......39

Transferring a Call ............... 23

Troubleshoong ...................31

Voice Mail .............................25

Voice Message Waing

Indicator Reset .........16, 25

W Wall Mount the Repeater/

Charger ..............................5

WARRANTY

One-year limited warranty

This product comes with a one year limited warranty. Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below.

UNIDEN XDECT R035BT

IMPORTANT Evidence of the original purchase is required for warranty service.

Warrantor: Uniden Australia Pty Limited ABN 58 001 865 498

Uniden New Zealand Limited

Elements of Warranty: Uniden warrants to the original retail owner for the duration of this warranty its UNIDEN XDECT R035BT (hereinafter referred to as the Product), to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.

Warranty Duration: This warranty to the original retail owner only is only valid in the original country of purchase and shall be of no further effect 1 year after the date of original retail sale. This warranty will be deemed invalid if the Product is: (A) Damaged or not maintained as reasonable and necessary, (B) Modified, altered or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) Improperly installed, (D) Repaired by someone other than an authorized Uniden Repair Agent for a defect or malfunction covered by this warranty, (E) Used in conjunction with any equipment or parts or as a part of a system not manufactured by Uniden. (F) Only available in the original country of sale.

Parts Covered: This warranty covers for one (1) year, the Product and included accessories.

Statement of Remedy: In the event that the Product does not conform to this warranty at any time while this warranty is in effect, the warrantor, at its discretion, will repair the defect or replace the

Product and return it to you without charge for parts and service. This warranty does not provide for reimbursement or payment of incidental or consequential damages. This EXPRESS WARRANTY is in addition to and does not in any way affect your rights under the TRADE PRACTICES ACT 1974 (Cth) (Australia) or the CONSUMER GUARANTEES ACT (New Zealand).

Procedure for obtaining performance or warranty: in the event that the Product does not conform to this warranty, the Product should be shipped or delivered, freight prepaid, with evidence of original purchase (e.g. a copy of the sales docket) to the warrantor at:

UNIDEN AUSTRALIA PTY LTD Service Division 345 Princes Highway, Rockdale, NSW 2216 Fax (02) 9599 3278 www.uniden.com.au

UNIDEN NEW ZEALAND LTD Service Division 150 Harris Road, East Tamaki, Manukau 2013 Fax (09) 274 4253 www.uniden.co.nz

Printed in Vietnam UNZZ01156BZ(0)

Uniden BLUETOOTH XDECT R035BT, XDECT R035, XDECT R035BT+1, XDECT R035BT+2, XDECT R035BT+3 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual