UNICOM Smart-Switch/801 FEP-30109T-C-SM, FEP-30109T-C-SM, Smart-Switch/801 FEP-30109T-T, FEP-30109T-T, Smart-Switch/801 FEP-30109T-C User Manual
8 Port 10/100Base-TX Switch
with 100Base-FX
Smart-Switch/801
USER’S MANUAL
SC/MM FEP-30109T-C
ST/MM FEP-30109T-T
SC/SM FEP-30109T-C-SM
Model shown: FEP-30109T-C
Smart-Switch/801
1
Features
Conforms to IEEE 802.3, 802.3u, and 802.3x Ethernet Standards
Eight auto-sensing 10/100Mbps Ethernet RJ-45 ports
Automatic MDI/MDIX crossover for each 10/100Base-TX port
One Fixed 100Mbps Fiber port (SC/ST-Multi-Mode, SC-Single
Mode)
Back-Pressure-Base flow control on Half-duplex mode
Pause-Frame-Base flow control on Full-duplex mode
Store-and-forward architecture for abnormal packet filtering
2K-entry MAC address table
96Kbytes memory buffer sharing
Non-blocking and Full wire speed forwarding rate
One console port for VLAN configuration and Port Setting
LED-indicators for Power, 10/100, LK/ACT, and FD/COL
10" Desktop size design
Smart-Switch/801
2
Package Contents
Unpack the contents of the Smart-Switch/801 and verify them against the
checklist below.
Smart-Switch/801 Fast Ethernet Switch
Power Cord
Four Rubber Feet
RS-232 console management cable
User Guide
Smart-Switch/801 Power Cord
Rubber Feet RS-232 cable User Guide
Figure 1-2. Package Contents
If any item is missing or damaged, please contact your local dealer for
service.
Smart-Switch/801
3
Hardware Description
This section describes the hardware of the Smart-Switch/801.
The physical dimensions of the Smart-Switch/801 are 250mm x 132mm x
37mm (L x W x H)
Front Panel
The Front Panel of the Smart-Switch/801 consists of eight auto-sensing
10/100Mbps Ethernet RJ-45 ports with automatic MDI/MDIX, one 100Base-
FX fiber port, and the LED indicators.
Smart-Switch/801 with SC Connector
Figure 2-2. The Front Panel of the Smart-Switch/801 with SC connector
Smart-Switch/801 with ST Connector
Figure 2-3. The Front Panel of the Smart-Switch/801 with ST connector
RJ-45 Ports (Auto MDI/MDIX): Eight 10/100 auto- sensing for
10Base-T or 100Base-TX connections.
100Base-FX Fiber Port: The operating range for the Multi-Mode
fiber option is up to 2Km while the SC Single Mode fiber variant can
support up to 30Km.
Smart-Switch/801
4
LED Indicators
Figure 2-4. LED Indicators
There are three LED Indicators (10/100M, LNK/ACT, FDX/COL) for each
UTP port and two LED Indicators (LNK/ACT, FDX/COL) for the fiber port.
The following table provides descriptions of the LED status. They provide
a real-time indication of systematic operation.
UTP Ports
LED Status Color Description
Power On Green Power On
On Green The port is operating at 100Mbps.
10/100
Off
The port is operating at 10Mbps
or no device attached
On Green
The port is successfully connecting
with the device.
Blinks Green
The port is receiving or transmitting
data.
LK /ACT
Off No device attached.
On Orange
The port is operating in Full-duplex
mode.
Blinks Orange
Collision of Packets occurring within
the port.
FDX /COL
Off
The port is operating in Half-duplex
mode or no device attached.
Smart-Switch/801
5
Fiber Port
LED Status Color Description
On Green
The port is successfully connecting with
the device.
Blinks Green
The port is receiving or transmitting
data.
LK /ACT
Off No device attached.
On Orange
The port is operating in Full-duplex
mode.
Blinks Orange
Collision of Packets occurring within the
port.
FDX /COL
Off
The port is operating in Half-duplex
mode or no device attached.
Table 2-1. Descriptions of LED Indicators
Smart-Switch/801
6
Rear Panel
The Console port and 3-pronged power plugs are located at the Rear
Panel of the Smart -Switch/801 as shown in Figure 2-8. This Switch will
work with AC in the 100-240V AC, 50-60Hz. Range.
Figure 2-5 The Rear Panel of the Smart-Switch/801
Console Port: Configuration is done through the console port connector.
This requires a direct connection between the switch and a device such
as a PC or terminal using the supplied RS-232 cable.
Desktop Installation
Set the switch on a sufficiently large flat space with a power outlet
nearby. The surface should be clean, smooth, level, and sturdy.
Make sure there is enough clearance around the Switch to allow air
circulation and the attachment of cables and the power cord.
Loading...