Unicol PZW TILTING MOUNT, KPL KIT, PZX FLAT MOUNT Installation Instructions Manual

UNIVERSAL SCREEN MOUNT

CODE: PZW TILTING MOUNT, PZX FLAT MOUNT & KPL KIT

INSPECT THE UNIT BEFORE INSTALLING
WARNING: Watch for pinch points. Do not put your fingers between movable parts. Do not tamper with or

dis-assemble the spring loaded arms of the PZW.

1. Carefully inspect the PZW Tilting Mount or PZX Flat Mount for shipping damage. If any damage is
apparent, call your carrier claims agent and do not continue with the installation until the carrier has
reviewed the damage.

NOTE: Read all instructions before starting the installation. The PZW differs from the PZX in that the PZW
Screen Arms have an additional spring loaded arm. Both units are assembled in the same way.

2. Lay out components to ensure you have all the required parts before proceeding (see Parts List on
Page 2).

CAUTION: To prevent damage to the PZW / PZX study all instructions and illustrations before you begin
the installation. Failure to do so could render the Warranty for the mount and the equipment that attaches
to it null and void. Pay particular attention to the “Warnings” displayed in these Instructions.

The maximum weight to be installed on the PZW / PZX wall mount is 60 Kg (132 Lbs).
The PZW / PZX wall mount is designed to be installed onto walls or Unicol screen stands and trolleys.

The structure to which the wall mount is anchored must be capable of supporting five times the total
weight of the mount and all attached equipment. We recommend installation by a Qualified Tradesperson,
using masonry plugs or other reliable fixings to ensure safe installation. Consult your builder or architect if
in doubt.

If you have any questions about the installation, contact Unicol [phone].

[phone] Page 1 www.unicol.de

INSTALLATION INSTRUCTIONS

Parts List:
We have either supplied the correct fixings for your screen or supplied a Universal Fixing Kit.
If in doubt consult the screen instructions for the correct size of fixing.

2 Screen
Arms (B)

(PZW shown)

1

INSTALLING BACK PLATE (A)
WALL INSTALLATION

1. Determine the exact mounting location prior to installation,
consider where the cables are routed from the wall in relation
to the hole in the centre of the back plate.

WARNING: Improper installation can result in serious personal
injury. Make sure that the structure can support a redundant
weight factor five times the total weight of the equipment: if not,
reinforce the structure before installing the PZW / PZX.

2. Using the Back Plate (A) as a template, mark, drill and plug
wall as necessary, fix the Back Plate to the wall ensuring that
the Plate is level.

CAUTION: We recommend installation by a Qualified
Tradesperson, using masonry plugs or other reliable fixings to
ensure safe installation. Consult your builder or architect if in
doubt.

1a

TROLLEY / STAND INSTALLATION

1. Attach the Back Plate (A) to the Trolley Mount Adapter plate
(shown on Trolley / Stand Instructions) using the 4 x M10 x
20mm Hex Head Screws supplied with the Trolley / Stand.

Back Plate (A)

WARNING

Universal mounts fit most screens. However, some screens

have more fixing points than Universal Mount arms can fix to.

In these circumstances consult the screen manufacturer’s

instructions to confirm how many fixing points have to be used.

If it is felt that the Arm fixing points are insufficient we

manufacture Xactmatch mounts specifically for individual

screens, which use the appropriate screen fixing points.

This is the PLW & PLX range.

PZW / PZX INSTALLATION

Universal Fixing Kit
contains:

2 x Griplock plates
with tags.
6 x Griplock plates
with 4 holes.
6 pairs of 2-part
plastic spacers.
6 x M8 x 35 button
head screws.
4 x M8 x 55 hex
head screws.
6 x M5 x 16 pozi pan
head screws.
6 x M5 flat washers.
8 x M4 x 12 pozi pan
head screws.
4 x M5 x 20 pozi pan
head screws.
4 x M5 x 40 pozi pan
head screws.
4 x M6 x 30 cap
head screws.

[phone] Page 2 www.unicol.de