Unex Technology DNMAH92 User Manual

WLAN 802.11a/b/g/n MiniPCI module

User Manual

Version: 1.0

Nov 2009

Copyright Statement

No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, whether electronic, mechanical,
photocopying, recording or otherwise without the prior writing of the publisher.
Windows™ XP/Vista are trademarks of Microsoft® Corp.
Pentium is trademark of Intel.

All copyright reserved.

1

FCC STATEMENT:

Federal Communication Commission Interference Statement This equipment has been
tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following
measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operation in conjunction with
any other antenna or transmitter.

This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted
in indoor environment only.

2

IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible
for the FCC compliance requirement of the end product, which integrates this module.

20cm minimum distance has to be able to be maintained between the antenna and the
users for the host this module is integrated into. Under such configuration, the FCC
radiation exposure limits set forth for an population/uncontrolled environment can be
satisfied.

Any changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at
least 20cm separation with the antenna while this end product is installed and
operated. The end user has to be informed that the FCC radio-frequency exposure
guidelines for an uncontrolled environment can be satisfied. The end user has to also
be informed that any changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this equipment. If the size of
the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is
required to be available in the users manual: This device complies with Part 15 of
FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains
TX FCC ID: NUK-DNMAH92 ". If the size of the end product is larger than 8x10cm, then
the following FCC part 15.19 statement has to also be available on the label: This
device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device

3

must accept any interference received, including interference that may cause
undesired operation.

4

Table of Contents

1. Introduction

6

2. Driver/Utility Installation / Uninstallation 7

2.1 INSTALLATION ..................................................................................... 7

2.2

ADDITIONAL SETUP PROCESSES ........................................................ 13

UNINSTALLATION .............................................................................. 14

2.3

3. Connecting to an Existing Network

17

4. Creating an Ad Hoc New Network 23

5. Modifying a Wireless Network 26

5.1 INFRASTRUCTURE MODE AND AD HOC MODE .................................. 26

MODIFYING A WIRELESS NETWORK .................................................. 27

5.2

DEFAULT SETTINGS WINDOWS XP ZERO-CONFIGURATION ............... 35

5.3

Appendix A: FAQ about WLAN

36

5

1. Introduction

Thank you for purchasing the WLAN a/b/g/n mini-card Module that provides the
easiest way to wireless networking. This User Manual contains detailed instructions in
the operation of this product. Please keep this manual for future reference.

System Requirements

z A laptop PC contains:

- 50 MB of free hard disk space (minimum)

- 256 MB of RAM or later (recommended)

- 900 MHz processor or higher

z Microsoft® Win™ 2000/XP/Vista

6

2. Driver/Utility Installation / Uninstallation

2.1 Installation

Note! The Installation Section in this User Manual describes the first-time installation

for Windows. To re-install the driver, please first uninstall the previously
installed driver. See Chapter 2.3 “Uninstallation” in this User Manual.

Follow the steps below to complete the driver/utility installation:

1. Install you card in your laptop and insert the Installation Software CD into the

CD-Rom Drive.

2. Click “Next”.

3. Read the License Agreement and choose “I accept the items of the license

agreement”, then click “Next”.

7

4. Choose this option to install the driver and client utilities, and click “Next”.

8

5. Click “Next” to continue or click “Browse” to choose a destination folder.

6. Click “Next” to continue or change the name of the program folder.

9

7. Click “Next”.

8. Choose the configuration tool for your client card and click “Next” to continue or.

10

9. Click “Yes” to continue.

10. Click “OK” to continue.

11. Installing process.

11