Uncle Milton's Toys Moon In My Room User Manual

MOON

MOON

IN MY ROOM

IN MY ROOM

With Light-up Lunar Phases

6+

2056

®

Installing batteries into Moon In My Room

Tool required - Small Phillips head screwdriver

1. Use a Phillips head screwdriver to remove the
battery cover (see Fig. 1).

2. Insert 4 “AA” batteries. Make sure the “+” and “-”
ends are inserted correctly, as indicated in the
battery compartment.

3. Replace cover.

4. IMPORTANT! Switch Moon in My Room to the “ON”
position before handing on the wall. (see Fig. 2).
PLEASE NOTE: The unit will not activate without the
remote control.

Installing batteries into the remote control

Tool required - Small Phillips head screwdriver

BATTERY SAFETY INFORMATION

• Non-rechargeable batteries are not to be recharged

• Rechargeable batteries are only to be charged under adult supervision

• Rechargeable batteries are to be removed from the toy before being charged

• Different types of batteries or new and used batteries are not to be mixed

• Batteries are to be inserted with the correct polarity

• Exhausted batteries are to be removed from the toy

• The supply terminals are not to be short-circuited

Battery

Figure 1

cover

1. Use a Phillips head screwdriver to remove the

battery door (see Fig. 3).

2. Insert 2 “AAA“ batteries. Make sure the “+” and

“-” ends are inserted correctly, as indicated in
the battery compartment.

3. Replace cover.

Figure 2

Figure 3

Hanging Moon In My Room

NOTE: The Moon In My Room is only intended to

hang on a vertical wall.

1. Hang the Moon In My Room by one of the three
hanging holes. (see Fig. 4)

2. Select any one of the 3 hang holes to angle the moon
to your desired position. This directly affects the angle
of the crescents.

Using Moon In My Room

IMPORTANT: Before operating, be sure on/off switch
located on the back of Moon In My Room is turned to the
“ON” position.

NOTE: In order for the moon to function properly, the room

lights should be off.

ON/OFF
switch

Hanging
holes

Figure 4

On/Off

To turn the moon off, press the ON/OFF button on
your remote. Press ON/OFF button again to
reactivate a full moon.

Auto Off

Moon automatically shuts off after 30-minutes if there
is no manual interaction.

Manual Phase

To manually cycle through the moon phases, press the
manual phase button (see figure 5). If you leave the moon
on in a phase, it will automatically turn off after 30
minutes.

Auto Phase

Your Moon In My Room will cycle through the moon
phases automatically, when you push the automatic
phase button. The moon will cycle from phase to phase in
five-second intervals. In this mode, the moon will
automatically turn off after 30-minutes.

KEEP THESE INSTRUCTIONS FOR
FUTURE REFERENCE — DO NOT DISCARD
Questions? Visit us at unclemilton.com

MANUFACTURED BY UNCLE MILTON INDUSTRIES, INC.
P.O. Box 6281
THOUSAND OAKS, CA 91359 USA

©2011 UMI. All rights reserved. ® and
trademarks o f Uncle Milton Indust ries, Inc.

MADE IN CHINA

TM

designate

Manual

phase

button

On/Off
button

Automatic

phase

button

Figure 5

Caution: changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.

NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help

2056- 0250-0411