Uncle Milton Wild Walls Wallscape FX Activator Instruction Manual

5+

2184

SCENE SET-UP

Install the Wallscape FX ActivatorTM on your Wall

Before installing your Activator, move the function switch on the back
of the Activator from “Try Me” to “Play”. This will enable full special
eects functionality.

The Activator should only be mounted on a vertical surface.
For optimal results, place a nail or screw into the wall approximately
4 feet from the oor. Then, position the Activator onto the wall by
placing the hang hole on the back of activator directly over the nail
until securely in place.

Note: For rooms with ceilings higher than 8 feet, you may want to
position the activator higher than 4 feet to ensure that the light
suciently illuminates the wall and the ceiling.

Wall Decal Preparation

After removing the decals from the package, roll out the sheet and lay
at for 24 – 48 hours until the sheet no longer wants to curl back up.

For best results apply the decals onto smooth, clean surfaces. The decals
may not stick to heavily textured surfaces. Do not apply to fresh paint or
wallpaper. Let the new paint/wallpaper dry for at least 3 weeks. Before
applying the decals to wallpaper or other delicate surfaces, test one in an
inconspicuous area. Keep the decals away from cribs and out of reach of
young children to prevent choking hazard.

Create your Scene by placing the Wall Decals

To apply each decal, carefully peel it o from the sheet. Then, place and
smooth the decal onto your wall in the desired location. To remove or
reposition each decal, just carefully peel it o from the wall. Kids can follow
the suggested scene layout or customize and create their own scene. For
optimal function with the light eects, please note the following suggestions
on wall decal placement:

• Begin with the lowest decal positioned 6” inches above the top of the
Activator.

• Then, place the bottom of the largest featured animal decal approximately
15” above the top of the Activator.

• Place all other decals around the featured animal decal but ideally no more
than 36 inches above the top of the Activator. This will help to
ensure that all decals are illuminated by the light cast.

On textured walls, periodically check the decals to make sure they are remaining at
against the surface. Gently smooth any parts of the decal, that appear to be lifting o the
surface. Repeat as needed until the decals remain at against the surface.

INSTRUCTION MANUAL

2

1

3

4

DO NOT SKIP THIS STEP

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE — DO NOT DISCARD

Questions? Visit unclemilton.com

Function
Switch

Hang
Hole

Battery
Cover

TRY ME

PLAY

Wallscape FX ActivatorTM Wallscape FX ActivatorTM

Scene Set-UpScene Set-Up

6” inches

15” inches

36” inches

Top of Wallscape

FX Activator

PRODUCT STYLES

MAY VARY

Floor

4 Feet

WildWalls-0250-0513

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.

Caution: changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

MANUFACTURED BY UNCLE MILTON INDUSTRIES, INC.

P.O. Box 6281
THOUSAND OAKS, CA 91359 USA

©2013 UMI. All rights reserved. ® and

TM

designate
trademarks of Uncle Milton Industries, Inc.
MADE IN CHINA

BATTERY SAFETY INFORMATION

• Non-rechargeable batteries are not to be recharged.

• Rechargeable batteries are to be removed from the toy before being charged.

• Rechargeable batteries are only to be charged under adult supervision.

• Dierent types of batteries or new and used batteries are not to be mixed.

• Batteries are to be inserted with the correct polarity.

• Exhausted batteries are to be removed from the toy.

• The supply terminals are not to be short-circuited.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

• Do not dispose of batteries in re. Battery may explode or leak.

SCENE ACTIVATION

Now you can activate your scene using dierent programming modes on the
Wallscape FX Activator as follows:

TRY ME (10 second demo)

This is the factory default program and is used for in store demonstration. It is not
intended for home use and has limited functionality. For full functionality, move the
function switch on the back of the Wallscape FX Activator from “Try Me” to “Play”.

MODE 1 – FULL FUNCTIONALITY LIGHT & SOUND SHOW

Press the program button once to activate. This will enable full light and sound
special eects including the following:

• Scene environment and animal sound eects

• Light gently fading in and out, illuminating your wall and ceiling

• Synchronized lights and sounds that bring the scene to life.
In this mode, auto shut-o of the sound will occur approximately after 5 minutes and auto
shut-o of the light will occur approximately after 10 minutes.

MODE 2 – LIGHT SHOW & SCENE ENVIRONMENT SOUNDS ONLY

Press the program button twice to activate. This will enable full light functionality but only the
scene environment sound eects. Auto shut-o timing is the same as Mode 1.

MODE 3 – LIGHT SHOW ONLY

Press the program button three times to activate. This will enable full light functionality but will
not include any sound eects. Auto shut-o will occur approximately after 20 minutes.

MANUAL SHUT-OFF

To manually turn o the Wallscape FX Activator, press and hold down the program button for
approximately two seconds until the light and sound turns o.

BATTERY REPLACEMENT

Tool required - Small Phillips head screwdriver
Requires 3 AA/LR6 alkaline batteries.

1. Using a Phillips head screwdriver, remove the battery cover.

2. Insert 3 AA/LR6 alkaline batteries as indicated in the battery
compartment and replace cover.

3. IMPORTANT! Switch the Wallscape FX Activator to the PLAY
position before hanging on the wall.

Function
Switch

Hang
Hole

TRY ME

PLAY

Program
Button

FOR BEST ILLUMINATION, USE IN A DARKENED ROOM.

Battery
Cover