Uncle Milton Spider-Man Web Creator Lab User Manual

CAUTION: DO NOT EAT! Web Gel compound may cause allergic reaction in hypersensitive individuals.

KEEP AWAY FROM EYES. Adult Supervision Suggested.

STAIN ADVISORY: AVOID WEB GEL COMPOUND CONTACT WITH PAPER, LEATHER, WOOD, STONE, MASONRY,
CARPETING, FABRICS, AND TEXTURED SURFACES. COMPOUND MAY STICK TO AND PERMANANENTLY STAIN
THESE SURFACES. IF CONTACT OCCURS, PROMPTLY REMOVE COMPOUND FROM THESE SURFACES.

Parts included:

- 1 Web Creator Lab Base

- 4 Web Creator Plates

- Large Web Top Plate

- Large Web Bottom Plate

- Multi-Web Top Plate

- Multi-Web Bottom Plate

- 1 Beaker

- 1 Web Injector

- 1 Web Extractor

- 2 Packs of Red, Sticky Web Gel

- 2 Packs of Blue, Stretchy Web Gel

Sticky Web Gel

Sticky Web Gel

Multi-Web Top PlateLarge Web Top Plate

Non-Sticky Web Gel

Stretchy Web Gel

6+

18015

Large Web Bottom Plate Multi-Web Bottom Plate

HOW TO CREATE SPIDER WEBS

Now you can create amazing webs just like Spider-Man using the Web Creator Lab. Make 4 dierent types of webs
including a large web, small action web, web ball, and web net. Each of these web types can be made as a sticky web,
using the red gel, or a stretchy web, using the blue gel. You can use the web gel over and over again by liquifying it and
using it to create fresh, new webs. To create your webs, follow these steps:

Frame Lock

1. Select the matching Large Web Plates or Multi-Web
Plates. First, place the bottom web plate into the
Web Creator Lab base. Be sure to align the web
plate correctly using the Plate Key. Add the top
plate, aligning with the Plate Key, and close the
cover. Press on all three Frame Locks to secure the
assembled Web Plates.

Frame Lock

Frame Lock

Injection Port
Plate Key

Top Plate

Bottom Plate

WARNING:

CHOKING HAZARD-Toy contains a small ball.
Not for children under 3 years.

2. Place one packet of red or
blue gel into the beaker
and ll with hot tap water
to the top ll line. Wait
until the gel has liquied
(about 5 min.).

4. Once the gel has
liquied, remove the gel
packet from the beaker.
With assistance from an
adult, carefully trim the
gel packet with scissors
along the dotted line
and squeeze the gel
into the Web Creator
Lab Injector.

Plunger

Sticky Web Gel

Fill Line

3. While you are
waiting for the gel
to liquify, insert the
Web Injector into
the Injection Port at
the center of the
Web Plate.

5. Insert the plunger into
the Web Injector and
gradually press
down to inject
gel into the
Web Plate until
the web cavity
is full.

Frame Lock

Web
Injector

Injection
Port

Injection Port

Frame Lock

Frame Lock

6. Wait 30 minutes for the web
to solidify at room tempera­ture. Then, open the cover
and slowly remove the

7. Your web is now ready to go. Fling your red, sticky
webs and web nets and watch them cling to
windows! Stretch and ing your blue webs at
villains! Bounce and splat your web balls!

Top Plate. Carefully
remove the web
using the Web
Extractor.

8. To reuse web gel to make new webs, place the used

web into the beaker. Place the beaker into a bowl

Web Extractor

lled with hot water to re-liquify the web gel. Once
the gel has completely liquied, repeat steps 4
through 7.

IMPORTANT: ONLY if needed, after reusing web gel ve times or more, add ONLY 5 drops of water to the web gel before
re-liquifying to recondition the gel to it’s original sticky formula.

CLEAN UP FOR HAIR, SKIN AND EYES AND ALL OTHER SURFACES NOT MENTIONED BELOW: Rinse with warm water.

CARPET CLEAN UP:

1. Promptly remove excess compound from carpeting.

2. Moisten area with sponge and hot water.

3. As compound softens, remove remaining compound with light
brushing.

4. If stain remains, apply carpet stain remover or rubbing alcohol. Some
light colored carpeting may stain permanently.

FABRIC CLEAN UP:

1. Remove excess compound from fabric.

2. Soak fabric in very warm water or hot water.

3. As compound softens, remove remaining compound.

4. Apply fabric stain remover to area.

5. Machine wash and repeat if necessary. Delicate fabrics (such as cotton)
and whites may stain permanently.

MANUFACTURED BY UNCLE MILTON INDUSTRIES, INC.

P.O. Box 6281
THOUSAND OAKS, CA 91359 USA

©2013 UMI. All rights reserved. ® and
trademarks of Uncle Milton Industries, Inc. © Marvel

ADE IN CHINA

M

TM

designate

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE — DO NOT DISCARD

Questions? Visit unclemilton.com

© Marvel

18015-0250-0523-V03